Advertisement
2600rpm
6.4mm
1350-2100rpm
9.5mm
1190-1350rpm
16mm
720-1190rpm
22mm
480-720rpm
31.75mm
350-480rpm
41.4mm
300-350rpm
50.8mm
6.1
Clean the tool after each use. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.
6.2
Blow out any dust that may have accumulated in the motor.
6.3
Periodically lubricate the table elevation rack/gear/worm mechanism and the spindle sleeve exterior.
Excessive noise:
Excessive drill wobble:
Drill binds in the workpiece:
Drill burns or smokes:
Table is difficult to raise:
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts
without prior notice.
purchase date, proof of which will be required for any claim.
01284 757525 and leave your full name and address, including postcode.
73/23/EEC LOW VOLTAGE DIRECTIVE
89/336/EEC EMC DIRECTIVE
98/37/EC MACHINERY DIRECTIVE
93/68/EEC CE MARKING DIRECTIVE
01284 757500
4.8mm
4mm
3.2mm
6.4mm
5.5mm
4.8mm
9.5mm
8.75mm
7.9mm
12.5mm
12mm
11mm
19mm
17.5mm
16mm
22mm
19mm
20.5mm
25.4mm
-
1. Incorrect belt tension.
2. Spindle is dry.
3. Pulley is loose.
4. Bearing damaged.
1. Chuck is loose.
2. Bearing or spindle shaft is worn.
3. Chuck is worn.
1. Feed pressure is too great.
2. Belt is loose.
3. Drill bit is loose.
4. Speed is too fast.
1. Speed is too fast.
2. Chips are not discharging.
3. Drill bit is dull.
4. Lubrication needed.
5. Feed pressure is too great.
1. Lubrication is needed.
2. Rack is bent.
No liability is accepted for incorrect use of this equipment.
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
01284 703534
2.4mm
1.6mm
3.2mm
2.4mm
6.4mm
4mm
8.75mm
6.4mm
12.5mm
9.5mm
16mm
12.5mm
-
-
-
1. Adjust tension.
2. Disassemble spindle/quill and lubricate.
3. Tighten pulley.
4. Replace the bearing.
1. Tighten the chuck by pressing it against the table.
2. Replace worn part.
3. Replace the chuck.
1. Apply less pressure.
2. Adjust tension.
3. Tighten the chuck jaws with the key.
4. Change the speed.
1. Change the speed.
2. Clean the drill bit.
3. Use a new bit.
4. Lubricate while drilling.
5. Apply less pressure.
1. Lubricate with light oil.
2. Straighten the rack.
For a copy of our latest catalogue and promotions call us on
, Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
1.2mm
0.8mm
1.6mm
1.2mm
3.2mm
1.6mm
4.8mm
3.2mm
7.9mm
6.4mm
11mm
9.5mm
14.5mm
12.5mm
Guarantee is 12 months from
For Jack Sealey Ltd.
Sole importer into the UK
15th December 2004
of Sealey Quality Machinery.
sales@sealey.co.uk
email
PDME160B-PDME200F - 1 - 151204
Advertisement
