Summary of Contents for MAC BRAIN1
- Page 1 CONTROL BOARD BRAIN1 Customer: Installing Company: CAREFULLY READ THE MANUAL BEFORE USE Brain_1_08 190722...
-
Page 2: Table Of Contents
CONNECTION OF CONTROL BOARD ___________________________________________ 4 2.0 TECHNICAL NOTES _______________________________________________________ 6 3.0 PROGRAMMING - FUNCTIONING __________________________________________ 7 4.0 SAFETY WARNINGS FOR MAINTENANCE AND USE __________________________ 10 WARRANTY _________________________________________________________________ 11 GUIDE FOR THE CAUSES RESEARCH OF SOME DRAWBACkS ____________________ 11 www.mac-srl.it Brain_1_08 190722... -
Page 3: Control Board
ANTENNA Entrance CommanDS InPUt antenna LeD eXt Before the installation, please read carefully this manual . the company declines any responsibility in case of non compliance with the laws in the country where the installation is done. info@mac-srl.it Brain_1_08 190722... -
Page 4: Connection Of Control Board
230Vac maX500W CLoSInG PHaSe *500W MAX FOR ENGINE -> MAX DURATION 10 SECONDS POWER SUPPLY INPUT OF CONTROL BOARD TERMINAL NOTES PHaSe CABLE ENTRY COMING FROM LINE DISCONNECTOR 230Vac 50 Hz neUtRaL BoaRD maSS (for GRoUnD connection) www.mac-srl.it Brain_1_08 190722... - Page 5 BoLLaRD HaS LaBeLLeD CaBLeS foR tHe eLeCtRICaL ConneCtIon WItH tHe ContRoL BoaRD. the current laws obligate this connection to avoid inopportune starting or missing stops in case of breakdowns (both on input side and output side). info@mac-srl.it Brain_1_08 190722...
-
Page 6: Technical Notes
- the installer must give all the information related to the functioning, maintenance and use of the single parts and of the system in its entireness following the Directive machine (see laws en 12635, en 12453 and en 12445). www.mac-srl.it Brain_1_08 190722... -
Page 7: Programming - Functioning
5) When the CH(7) button is released, the led OK turns off and the procedure is finished During the normal functioning the automatic reclosing can be excluded by sending the Start/Stop command during the pause or by activating the emergency stop. info@mac-srl.it Brain_1_08 190722... - Page 8 3) Release the PROG button, the led OK keeps on flashing. 4) Push and keep pushed the aP button for the time you wish to memorize. 5) When the AP button is released, the OK led turns off and the procedure’s finished image a www.mac-srl.it Brain_1_08 190722...
- Page 9 Usually, the engines stop after 250ms from the opening of the contact of the limit switches. thanks to this procedure it is possible to exclude the delay letting stop the engines as soon as the limit switch contact is open. It turns on placing the DIP4 in on. info@mac-srl.it Brain_1_08 190722...
-
Page 10: Safety Warnings For Maintenance And Use
In case of maintenance, cleaning, breakdown or malfunction of the product, turn off the power supply and avoid any attempt of intervention except when indicated. -
Page 11: Warranty
- magnetic limit switches are -magnetic limit switch -establish the right position for limit bollard stops) closed (lights fC1 e fa1 reading zone of magnet switches reading between the magnet switch on about mot1) sensor(bringing near magnetc limit switch) info@mac-srl.it Brain_1_08 190722... - Page 12 Read carefully the control board manual for the cables section and length. Buzzer 230Vac Electrical valve 230V FC A M1 FC C SIC1 Stop (blocco) 230 Vac 50Hz ANTENNA Entrance FC A M1 FC C SIC 1 www.mac-srl.it Brain_1_08 190722...
- Page 13 COMMON BRAIN info@mac-srl.it Brain_1_08 190722...
- Page 14 Connection in series with the other securities connected on this clamp 13 14 15 16 230 Vac 50Hz POWER SUPPLY 12 11 10 9 www.mac-srl.it Brain_1_08 190722...
- Page 15 Brain_1_08 190722...
- Page 16 Brain_1_08 190722...
Need help?
Do you have a question about the BRAIN1 and is the answer not in the manual?
Questions and answers