Figures - ABB HT609429 Operation Manual

Operation Manual / A130-H.. - A140-H..

Figures

Figures
Fig. 1: Serial number (01) on the rating plate ........... 4
Fig. 2: Layout and function of the turbocharger...... 6
Fig. 3: Compressor wheel cooling ................................ 7
Fig. 4: Volatile Corrosion Inhibitor (VCI)................... 10
Fig. 5: Package with hygrometer................................ 11
Fig. 6: Warning plate locations ................................... 16
Fig. 7: Rating plate ........................................................ 17
Fig. 8: Locations of the rating plates ........................ 18
Fig. 9: Attachment of loads on the crane hook ....... 19
Fig. 10: Attachment angle............................................ 19
Fig. 11: Transportation of the turbocharger ........... 28
Fig. 12: Removing the turbocharger ......................... 29
Fig. 13: Loosening the clamping nut.......................... 31
Fig. 14: Putting down the turbocharger ................... 32
Fig. 15: Inserting gaskets into the bracket............... 33
Fig. 16: Fitting threaded rods onto the bracket..... 34
Fig. 17: Requirements for threaded rods................. 34
Fig. 18: Placing the turbocharger on the bracket .. 35
Fig. 19: Preparing the clamping nut for the tighten-
ing procedure ................................................................ 37
Fig. 20: Tightening pressure screws ........................ 38
Fig. 21: Connecting the compressor cooling air in-
take ................................................................................. 39
Fig. 22: Attaching the support ................................... 39
Fig. 23: Oil orifice ........................................................... 41
Fig. 24: Layout and overview of speed measurement
system ............................................................................ 48
Fig. 25: Replacing the speed sensor ......................... 50
Fig. 26: Noise insulation, bellows.............................. 52
Fig. 27: Replacing the protective grid ...................... 55
Fig. 28: Cleaning the filter silencer............................ 62
Fig. 29: Compressor-end, non-rotating parts ........ 64
Fig. 30: Turbine end, non-rotating parts ................. 65
Fig. 31: Soaking the turbine end ................................ 68
© Copyright 2021 ABB. All rights reserved.
Fig. 32: Swivel lifting eyes ............................................ 80
Fig. 33: Starpoint ring nut VRM................................... 80
Fig. 34: Weights of assemblies ................................... 81
Fig. 35: Removing the air inlets................................... 82
Fig. 36: Removing the gas outlet casing ................... 83
Fig. 37: Dismantling the gas outlet flange................ 84
Fig. 38: Removing the gas outlet flange ................... 85
Fig. 39: Removing the compressor casing................ 86
Fig. 40: Dismantling the wall insert ........................... 87
Fig. 41: Press off the casing......................................... 88
Fig. 42: Oil orifice ........................................................... 89
Fig. 43: Removing cartridge group 1.......................... 89
Fig. 44: Removing cartridge group 2 ......................... 90
Fig. 45: Removing the nozzle ring .............................. 91
Fig. 46: Installing the cartridge group on the service
support ............................................................................ 92
Fig. 47: Measuring clearance A and B ........................ 93
Fig. 48: Nozzle ring compression PD ......................... 94
Fig. 49: Installing the nozzle ring................................ 95
Fig. 50: Measuring the end position of the nozzle
ring ................................................................................... 96
Fig. 51: Lifting the cartridge group and rotating it by
90°..................................................................................... 96
Fig. 52: Installing the cartridge group ....................... 97
Fig. 53: Fitting the wall insert and the diffuser ....... 98
Fig. 54: Installing the compressor casing................. 99
Fig. 55: Measuring clearances N and R .................... 100
Fig. 56: Installing the air inlets .................................. 101
Fig. 57: Installing the gas outlet flange ................... 102
Fig. 58: Installing the gas outlet casing .................. 102
Fig. 59: Tightening torques ...................................... 103
Fig. 60: SPI Air suction branch radial ........................ 116
HZTL4030_EN Revision G July 2021