Table of Contents
Advertisement
Quick Links
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit
guide
About this document
Scope and purpose
This document is a user guide for the CY-SD4210 EZ-USB™ SX3 HDMI 4K capture solution demo kit. This kit
enables you to stream video and audio from an external HDMI source directly into a PC. See the relevant
sections based on your requirements:
Introduction
– Provides basic information on the kit
•
Installing the kit software
•
Kit hardware
– Explains the kit architecture and system design details
•
Kit programming
– Describes the procedure to program the kit
•
Kit operation
– Explains the procedure to operate the kit
•
Intended audience
This document is intended for users of the EZ-USB™ SX3 HDMI 4K capture solution demo kit.
User Guide
www.infineon.com
– Explains the installation of software needed to program the kit
Please read the Important Notice and Warnings at the end of this document
page 1 of 25
002-34554 Rev. *A
2022-08-01
Advertisement
Table of Contents
Summary of Contents for Infineon CY-SD4210
-
Page 1: About This Document
Scope and purpose This document is a user guide for the CY-SD4210 EZ-USB™ SX3 HDMI 4K capture solution demo kit. This kit enables you to stream video and audio from an external HDMI source directly into a PC. See the relevant... -
Page 2: Table Of Contents
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Table of contents Table of contents About this document ........................1 Table of contents ..........................2 Introduction .......................... 3 Kit contents ............................. 3 Downloading kit documents and hardware design files ............... 3 Board details ............................ -
Page 3: Introduction
Introduction Introduction The CY-SD4210 EZ-USB™ SX3 HDMI 4K capture solution demo kit is based on the SX3 product family of Infineon’s configurable SuperSpeed USB controllers. SX3 has a fully configurable general interface that can interface with any processor, ASIC, image sensor, or FPGA. -
Page 4: Kit Features
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Introduction Figure 1 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit Kit features The kit features an SX3 controller and ECP5 FPGA from Lattice Semiconductor that can be configured using the configuration provided to stream video and audio from an external HDMI source directly into a PC. The onboard ITE HDMI receiver enables users to stream HDMI video up to 4K at 30 fps. -
Page 5: Installing The Kit Software
After the installation is complete, the contents are available at <Install Directory>\ EZ-USB SX3 Configuration Utility. Note: 1. For working with CY-SD4210 kit, SX3 Configuration Utility tool version should be v1.1.0.5 or higher. 2. The default <Install Directory> is C:\Program Files(x86)\Cypress. 3. See EZ-USB™... -
Page 6: Ez-Usb™ Sx3 Hdmi 4K Capture Kit System Design
EZ-USB™ SX3 HDMI 4K capture kit system design This section provides details of the CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit design. The kit is bus-powered and supports a SuperSpeed USB-C cable to connect to the PC. To demonstrate the full functionality of the kit, an HDMI source must be connected to the onboard HDMI connector. -
Page 7: Power Supply
Additionally, a dedicated 19.2 MHz crystal input support is also available. 3.2.5 SPI flash (U11) The kit configuration is stored on an Infineon Technologies 64-Mb SPI flash. After power-on, SX3 fetches the required details from the configuration image, stores it in its RAM and starts executing from it. 3.2.6 HDMI connector (J6) The kit has an onboard HDMI connector that allows it to connect to an external HDMI source using an HDMI cable. -
Page 8: Ddr3 Ram (U12)
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide EZ-USB™ SX3 HDMI 4K capture kit system design 3.2.11 DDR3 RAM (U12) This kit has an onboard 2 Gb DDR3 SDRAM that is used by the FPGA to process the digital audio and video data received from the HDMI receiver and communicate it to SX3 via the 32-bit slave FIFO. -
Page 9: Programming The Ez-Usb™ Cy-Sd4210 Sx3 Controller
The CY-SD4210 kit is preprogrammed with the firmware to stream 4K videos at 30 fps from an HDMI source. Use the Configuration Utility only to change the program. Ensure that the tool version is 1.1.0.5 or higher. - Page 10 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Programming the EZ-USB™ CY-SD4210 SX3 controller 3. Browse to import the following configuration from the local folder based on the module planned for streaming and click Open. Table 3 Project files Streaming media...
- Page 11 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Programming the EZ-USB™ CY-SD4210 SX3 controller Figure 7 Selected folder 5. Set the mode switch SW1 setting to USB by moving the SW1 pin 1 to OFF and pin 2 to the ON position.
- Page 12 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Programming the EZ-USB™ CY-SD4210 SX3 controller Cypress FX3 BootLoader Device appears in Device Manager > Universal Serial Bus controllers. Figure 10 FX3 bootloader device appearing in Device Manager If the device is detected as “WestBridge”, it means the cyusb3 driver is not installed. For more Note: details on how to install the cyusb3 driver , see the Troubleshooting section 6.1.2.
- Page 13 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Programming the EZ-USB™ CY-SD4210 SX3 controller Figure 12 Program download 8. Wait for the programming to complete, and when done, click Close. Figure 13 Programming successful User Guide 13 of 25 002-34554 Rev. *A...
-
Page 14: Kit Operation
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation Kit operation This chapter describes how to boot the SX3 device after successful programming to demonstrate the kit functionality by streaming video and audio. Two separate demonstrations are covered: Streaming 1080p video •... -
Page 15: Audio Setting
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation 3. Plug in the HDMI cable connected to the kit to an HDMI source such as a laptop, set-top box or gaming console. ITE6802 appears in the Device Manager only if the same laptop is used as an HDMI source. -
Page 16: Video Streaming At 4K Resolution
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation Note: If the same laptop is used as an HDMI source; check and select the ITE6802 as the default playback device in the Playback tab as Figure 18 shows. Figure 18... -
Page 17: Video Streaming At 1080P Resolution
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation 3. Check if the video is streaming. An example image is shown below: Figure 20 Video streaming from PC HDMI source 4. Check the camera setting for picture quality. It should display the quality as 3840 x 2160, indicating streaming at 4K. - Page 18 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation Figure 22 Microsoft Camera app 3. Check if the video is streaming. An example image is shown below: Figure 23 Video streaming from PC HDMI source 4. Check the camera setting for picture quality. It should display the quality as 1920 x 1080, indicating streaming at 1080p.
- Page 19 CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Kit operation Figure 24 1080p streaming in camera settings 5. Flip the camera again to turn OFF the streaming and disconnect the USB and HDMI cable from the PC and the board.
-
Page 20: Troubleshooting
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Troubleshooting Troubleshooting Programming test 6.1.1 No bootloader device detected If a “No Bootloader Device Detected” message appears during programming from the SX3 Configuration Utility, verify that the PMODE switch (SW1) is in the “USB” state. -
Page 21: Video Streaming Test
Check the debug logs: Open Tera Term. Connect to the COM port associated with the SX3 device. Check if any error messages are displayed. Note: If the above troubleshooting steps do not resolve the problem, visit the Infineon Technical Support page. User Guide 21 of 25 002-34554 Rev. -
Page 22: References
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide References References [1] Overview: Infineon USB controller roadmap [2] Product webpage: EZ-USB™ SX3 webpage [3] Kit webpages: CY-SD4210 webpage [4] Datasheets: EZ-USB™ SX3 datasheet [5] Application note: AN231295 – Getting started with EZ-USB™ SX3... -
Page 23: Technical Support
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Technical support Technical support If you have any questions, create a support request on the Infineon Technical Support page. User Guide 23 of 25 002-34554 Rev. *A 2022-08-01... -
Page 24: Revision History
CY-SD4210 EZ-USB™ SX3 HDMI 4K capture kit guide Revision history Revision history Date Version Description of changes 2022-01-04 Initial release with document number 002-34554 and registration number UM_2207_PL91_2207_143022 2022-08-01 Added a note and Figure 18 in Section on how to select an ITE device if... - Page 25 With respect to any examples, hints or any typical 81726 München, Germany values stated herein and/or any information WARNINGS regarding the application of the product, Infineon Technologies hereby disclaims any and all Due to technical requirements products may contain warranties and liabilities of any kind, including dangerous substances.