Telegesis ZHT100 Quick Start Manual

Issue: 3
Date: Sept 2012 Start Guide
ZigBee RangeFinder
Quick Start Guide
(b)
(d)
(e
(g)
Handheld (HHT)
(a) Product Model Number
(b) LCD Display
(c) Navigation Keys
(d) Value Change Keys
(e) Escape (Back) Key
(f) Enter (Activate) Key
(g) Power On/Off Key
Telegesis (UK Ltd., Abbey Barn Lane, High Wycombe, HP10 9QQ, United Kingdom Ph: 01494 510199 Email: zigbeesupport@telegesis.com
(a)
(j)
(h)
(i)
(c)
(f)
Satellite (IHD and GAS)
(h) Product Model Number
(i) Power On/Off Key
(j) Activity and Battery Status
Indicator
Using the Range Finder
Power On/Off
·
To power on press the Power Key (g) for about 3 sec-
onds until the Welcome Screen is displayed
·
To power off press the Power Key (g) until the screen
goes blank
Welcome Screen
Upon power up the welcome screen pops up displaying
information about the device firmware and the serial num-
bers of devices paired as shown below. Press any key to
exit from this screen.
RANGE FINDER
2.4GHz Zigbee
Network Surveyor
HHT : xxx VER : xxx
IHD : xxx GAS : xxx
Press Any Key
Main Menu Screen 1
Use navigation keys to scroll through various menu
options. Use keys to scroll between IG and I option.
Pre- Test Test
Test A B
Energy I G
Con g
Scan
To use both IHD and GAS for test.
IG
To use only IHD for test.
I
Press OK to use the setting for the current session or
to select any menu option.
Main Menu Screen 2
Tx Ch
Ch
Ping
Tone E-Scan
FW Data
Upgrades Logger
The battery symbol indicates the capacity or charging
status of the battery of the handheld. Further details of
Menu Screen 2 options can be found in the user manual.
Data Logging Configuration (Data Logger)
The HHT will record the results from Test-A/B and Energy
Scan into built-in storage. After exiting the welcome screen
the data logging config screen will appear which enables
the operator to enter the SITE ID for the current session.
The SITE ID will be stored with the test results of the cur-
rent session (more details in the user manual).
At every new site, change the SITE ID by navigating to
EDIT option on screen using keys and press
OK. The SITE ID is an alphanumeric field of 16 characters
and can be edited by using keys.
Once the SITE ID is changed press OK key on keypad to
hear a beep from device as confirmation.
Data Log Config
SITE ID
DEFAULT SITE ID
EDIT OK
MEMORY AVAIL
1024 KB
Please enter a unique SITE ID for each location as this is
used as record identifier in the data logs. This option can
also be accessed by selecting Data Logger menu option
on Menu Screen 2.
Pre-Test
This is used to test the link between the Range Finder
handheld unit and the satellites IHD and GAS.
The results are shown in the following screen and include:
·
Serial number of the IHD or GAS unit.
·
Battery capacity at IHD and GAS units.
·
RSSI level measure during the Pre-Test.
·
Overall result of OK or NOK for Pre-Test Pass or
Fail.
The bottom row shows:
·
The Zigbee RF channel used for Pre-Test.
·
The transmit power used for Pre-Test.
·
The battery status of handheld unit.
IHD GAS
65534 65535
Link : OK Link
: NOK
Bat : 4 % Bat : 4 %
RSSI : -20 RSSI : -20
Ch: 11 Pw:8dBm Bat:100%
Pre-Test transfers all the test settings from HHT to the IHD
and GAS units for current session, so it is important to get
an OK from this test in order to perform any further tests.
Press ESC key to exit the test and go back to menu
screen.