1. Manuals
  2. Brands
  3. Zimmer Manuals
  4. Transducer
  5. PRO -V
  6. Manual

Zimmer PRO -V Manual

Programmable transducer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZIMMER PRO -V
Programmable Transducer
Installation & Operating Instructions
Section
Contents
1.
Introduction
2.
Input and Output screens
3.
3.1 Programming via Front LCD & Tow keys
3.1.2.1 Potential Transformer primary value
3.1.2.2 Potential Transformer secondary value
3.1.6.1.1 End value of output 1
3.1.6.1.2 Start value of output 1
3.1.6.1.3 Elbow value of output 1
3.1.6.2.1 End value of output 2
3.1.6.2.2 Start value of output 2
3.1.6.2.3 Elbow value of output 2
3.2 Programming Via Programming port
4.
RS 485 ( ModBus )
5.
Installation
5.1 EMC Installation Requirements
5.2
Case Dimensions and Panel Cut-out
5.3
Wiring
5.4
Auxiliary Supply
5.5
Fusing
5.6
Earth / Ground Connections
6.
Specification
7.
Connection Diagrams
1. Introduction
The Zimmer PRO -V is a panel mounted 43.5X 65.5mm Transducer.
The Zimmer PRO -V is used to measure and convert AC Voltage input into an
proportional DC current or voltage output signal. Output signal generated is proportional
to the True RMS(upto 15th Harmonic) of the input Voltage.
Input Voltage and Output Voltage/Current is displayed on LCD and indicated by LED's.
ON O/P1 O/P2
COM
INPUT x012
A
O/P 12 y012
A
Zimmer PRO -V
1.1 LED Indication
LED OPERATING
LED
CONDITION
Aux. Supply healthy
ON
condition
Output1 voltage
O/P 1
Output1 Current
Output2 voltage
O/P 2
Output2 Current
ZIMMER
15030988_Rev.A - 10/11
Zimmer PRO -V can be configured and
programmed at site for the following :
PT Primary ,PT Secondary,
Input parameters (i.e start, end and
elbow value of Input) and Output
parameters(i.e as Voltage or as Current
and start, end and elbow value of outputs).
The front panel has two push buttons through
which the user may scroll through the
output screens and configure the product.
LED OPERATING
STATUS
Green LED
continuous ON
Green LED
continuous ON
Red LED
continuous ON
Green LED
continuous ON
Red LED
continuous ON
PRO-V
PRO-V
Table 1: Measured parameters
Measured parameters
Voltage
.
2
Input and Output screens
In normal operation the user is presented with display test screen followed by version screen
to one of the output screen. These screens may be scrolled through one at a time
by pressing the "
Up key" or "
Screen 1 : Display Test
ON O/P1 O/P2
COM
INPUT x012
A
O/P 12 y012
A
Zimmer PRO -V
Screen 3 : Voltage Input and
Output 1 as Voltage
ON O/P1 O/P2
COM
INPUT
INPUT x012
A
O/P 1
O/P 12 y012
A
Zimmer PRO -V
Screen 5 : Voltage Input and
Output 2 as Voltage
ON O/P1 O/P2
COM
INPUT x012
INPUT
A
O/P 12 y012
O/P 2
A
Zimmer PRO -V
www.zimmer-instruments.com
Unit of Measurement
Volt
Down key".
Screen 2 : Version Screen
ON O/P1 O/P2
COM
Zimmer PRO -V
Screen 4 : Voltage Input and
Output 1 as Current
ON O/P1 O/P2
COM
INPUT x012
INPUT
A
O/P 12 y012
O/P 1
A
A
Zimmer PRO -V
Screen 6 : Voltage Input and
Output 2 as Current
ON O/P1 O/P2
COM
INPUT x012
INPUT
A
O/P 12 y012
O/P 2
A
A
Zimmer PRO -V
1
|
16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRO -V and is the answer not in the manual?

Questions and answers

Summary of Contents for Zimmer PRO -V

  • Page 1: Table Of Contents

    Output 2 as Voltage The Zimmer PRO -V is a panel mounted 43.5X 65.5mm Transducer. The Zimmer PRO -V is used to measure and convert AC Voltage input into an proportional DC current or voltage output signal. Output signal generated is proportional...

  • Page 2: Programming

    3.1 Programming via Front LCD & Two keys the “Enter Password” entry stage. The following sections comprise step by step procedures for configuring the Zimmer PRO - V for individual user requirements. Pressing the “ Up” key will exit the To access the set-up screens press and hold the “...

  • Page 3: Potential Transformer Parameter Selection

    Pressing “ Up” key will confirm the present value as and advance to the PT secondary selection (section 3.1.2.2). PT Primary and advance to the PT secondary selection (section 3.1.2.2). Zimmer PRO -V O/P 12 y012 Zimmer PRO -V 3.1.2.2...

  • Page 4: Communication Parameter Selection

    Pressing “ Up” key will confirm the present value as Baud rate and advance to the Parity Selection(section 3.1.3.3). and advance to Baud Rate selection (section3.1.3.2) . Zimmer PRO -V RS 485 Baud Rate confirmation Zimmer PRO -V ON O/P1 O/P2 Pressing “...

  • Page 5: Output Type Selection

    Pressing the “ Up” key will advance the operation to the next digit and set the second digit, in this case to “5”. Zimmer PRO -V Pressing “ Up” key will confirm the present type for Output 1 and advance to the Output 2 type selection(section 3.1.4.2).

  • Page 6: Elbow Function Selection

    Pressing the “ Up” key will advance the operation to the next digit and set the third digit, in this case to “5”. Zimmer PRO -V Zimmer PRO -V Enter New / Change Start value of Input, third digit entered, ON O/P1 O/P2 prompting for fourth digit.

  • Page 7: Output Parameter Selection

    O/P 1 selection(section 3.1.6.2) End value of the Output 1 and advance to the Start value of Output 1(section 3.1.6.1.2). O/P 1 Zimmer PRO -V Zimmer PRO -V Start New / Change value of the Output 1 ON O/P1 O/P2...

  • Page 8: Output 2 Parameter Selection

    End value of the Output 2 and advance to the Start value parameter selection(section 3.1.6.2). of Output selection(section3.1.6.2.2). O/P 1 O/P 2 Zimmer PRO -V Zimmer PRO -V New / Change Elbow value of the Output 1 ON O/P1 O/P2...
  • Page 9 Start value of the Output 2 and advance to the Elbow value of Output selection(section 3.1.6.2.3) or exit setup menu. O/P 2 O/P 2 O/P 2 O/P 2 O/P 2 Zimmer PRO -V Zimmer PRO -V New / Change Elbow value of the Output ON O/P1 O/P2 New / Change...
  • Page 10 For setting Output from Voltage to Current write value “2”. (Refer section 4.2 and table 3 parameters no. 16 & 18 for details). 1234 The power supply must be applied to Zimmer PRO - V before it can be programmed. 1234...
  • Page 11 Data register 2 Low Byte : Least significant 8 bits of Data register 2 of the parameter requested. The maximum latency time of an Zimmer PRO -V is 200ms i.e. this is the amount of time that can pass before the first response character is output.
  • Page 12 Start Address low :Least significant 8 bits of starting address of the parameter requested. Number of register Hi : Most significant 8 bits of Number of registers requested. Number of register Lo : Least significant 8 bits of Number of registers requested. (Note : Two consecutive 16 bit register represent one parameter.) www.zimmer-instruments.com...
  • Page 13 5.4 Auxiliary Supply Zimmer PRO - V should ideally be powered from a dedicated supply, however it may be powered from the signal source, provided the source remains within the limits of the chosen auxiliary voltage.
  • Page 14 Rn = Y2 / 1 mA ± 1% With DC Voltage output signal. Miscellaneous Acc. to IEC EN - 60688 Additional Error : ± 0.2% /10°C Temperature influence Influence of Variations: As per IEC EN-60688 standard. Output stability < 30min www.zimmer-instruments.com...
  • Page 15 .Environmental: O/P 12 y012 Nominal range of use 0 °C...23 °C... 45 °C(usage Group II) Storage temperature -40 °C to 70 °C ≤ Zimmer PRO -V Relative humidity of annual mean Altitude 2000m max Ambient tests: EN 60 068-2-6 Vibration Acceleration ±...
  • Page 16 NOTES www.zimmer-instruments.com...

Table of Contents