CONTENTS Safety precautions……………………………………………………………..……………3 TV block diagram……………………………………………………………………..…….4 Replacement of memory IC………………………………………………………….……5 Service adjustment……………………………………………………………..…………...5 ICs functional description…………………………………………………………………8 Test point waveform………………………………………………………………………10 All ICs voltages……………………………..……………………………………………….10 Purity / convergence adjustment………………………………………………………11 DVD maintenance…………………………………………………………………………13 10. List of Parts ………………………………………………………………………….…….14 11. Circuit diagram………………………………………………………………………Attached 12. Exploded view…………………………………………………………………Attached...
1. SAFETY PRECAUTIONS The design of this product contains special hardware, many manufacturer’s replacement components. circuits and components especially for safety purposes. For Isolation Check continued protection, no changes should be made to the (Safety for Electrical Shock Hazard) original design unless authorized in writing by the After re-assembling the product, always perform an isolation manufacturer.
3. REPLACEMENT OF MEMORY IC 1. MEMORY IC. This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and deflection circuits. 2. PROCEDURE FOR REPLACING MEMORY IC (1) Power off Switch the power off and unplug the power cord from AC outlet. (2) Replace IC Be sure to use memory IC written with the initial data values.
Page 6
Adjustable Items Direct access key Items Description Preset Remark “1” 5/6HSH Horizontal shift “2” 5/6VSL Vertical slop 5/6VAM Vertical amplitude 5/6SCL S-correction 5/6VSH Vertical shift 5/6VOF OSD Vertical offset HOF* OSD Horizontal offset “3” Black level offset R Black level offset G White point R White point G White point B...
Page 7
2. OP2 Function Description Preset Remark Bit 7 1=21dBµV 0=26dBµV Bit 6 1=Enable Bit 5 ARABIC_SET 1=Enable Bit 4 FARSI_SET 1=Enable Bit 3 CYRILLIC_SET Bit 2 EUROUP_SET 1=Enable Bit 1 AUTO_SOUND Bit 0 1=Enable 3. OP3 Function Description Preset Remark Bit 7 RUSSIA 1=Enable...
7. OP7 Function Description Preset Remark Bit 7 FMWS 1=Enable Bit 6 HOTEL 1=Enable Bit 5 PROG_ID 1=Enable Bit 4 1=Enable Bit 3 TWIST 1=Enable Bit 2 BYELORUSSIAN 1=Enable Bit 1 UKRANIAN 1=Enable Bit 0 1=Enable 8. OP8 Function Description Preset Remark Bit 6...
Page 9
IREF Reference current input Vertical sawtooth capacitor TUNER AGC Tuner AGC output AUDEEM/SIFIN1 *1 Audio deemphasize or SIF input DECSDEM/SIFIN2 Decoupling sound demodulator GND2 Ground 2 for TV processor SNDPLL/SIFAGC *1 Narrow band PLL filter Automatic Volume Levelling HOUT Horizontal output FBISO Flyback input/sandcastle output AUDEXT...
In 1 Ch 1 input Out 2 (+) Ch 2 output (+) 4. N301: Vertical output (TDA8357A) Symbol Function Symbol Function INV IN Input PUMP UP Pump up power INV IN Input V OUT Vertical output Pump up power V PRO Vertical protection V OUT Vertical output...
Page 12
PURITY ADJUSTMENT WEDGE Demagnetize CRT with the demagnetizer. DEFLECTION YOKE Loosen the retainer screw of the deflection yoke. Remove the wedges. Input a green raster signal from the signal generator, and turn the screen to green raster. Move the deflection yoke backward. P/C MAGNETS Bring the long lug of the purity magnets on the short P: PURITY MAGNET...
STATIC CONVERGENCE ADJUSTMENT 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets overlap the red and blue lines in the center of the screen (Fig. 1) and turn them to magenta (red/blue). (FRONT VIEW) 3. Using 6-pole convergence magnets overlap the magenta (red/blue) and green lines in the center of the screen and turn them to white.
Page 14
9. DVD Part: Introduction of MTK1379 maintenance Under normal power supply conditions, the maintenance plan for MT1379 mono-chip is: first the reset circuit resets the MT1379, after the crystal oscillator circuit gave the clock signal to MT1379, MT1379 will start the initialization check for Flash、E PROM、SDRAM, after everything is checked to be normal, it will start initialization check for 7Audio DAC, MT1336 and motor Driver.
2) There is RF signal,but not in normal status,then check MT1336 and surrounding circuits. )Everything is normal, but the disc cannot be read out, check MT1369 and its surrounding circuit 10. List of Parts PART LOCATION DESCRIPTION NUMBER FRONT CABINET ASS’Y BCJ7008-----Q 90806302 LENS...
Page 16
90204759 PLASTIC BAG FOR USER MANUAL 94009887 REMOTE CONTROL PLASTIC BAG FOR 21” COMPLETE SET 90500102 PLASTIC BAG FOR POWER CORD 90500018 USER MANUAL 90504553 TELESCOPIC MAST 94501185 MAIN BAORD ASS’Y 94008724 N301B HEAT SINK HEAT SINK 90100450 N301C TDA8357J 94401409 N301D SCREW...
Page 26
Exploded view part list Exploded view part list MATERIAL CODE PARTS NAME Q’TY REMARK 0090503696 Switch batton 0090204556 Front frame 0090204556 Dvd stand 0094006927 Main board 0090204546 stand 0094009819 Main board 0094000748 0094008903 Speaker 0090204557 Rear cover...