Summary of Contents for Jam JT864P-A
- Page 1 INTERNATIONAL PROGRAMMABLE AUTOMATIC FLAT-BED SEWING MACHINE JT864P-A JT864P-A-95 INSTRUCTION MANUAL...
- Page 2 INDEX GENERAL FEATURES GENERAL WARNINGS MANUFACTURER RESPONSABILITY MODIFICATIONS IDENTIFICATION PLATE TECHNICAL SERVICE SAFETY TRAINING SAFETY INSTRUCTIONS NOT ALLOWED USE INDIVIDUAL SAFETY DEVICES REMAINING RISKS SAFETY SIGNS MOVING, STORAGE, DISPOSAL MOVING AND TRANSPORTATION LIFTING PACKAGE AIR NOISE USE OF THE MACHINE MINIMUM DISTANCE FOR A PROPER MAINTENANCE CONNECTION TO THE ELECTRIC SYSTEM CONNECTION TO THE PNEUMANTIC SYSTEM...
- Page 3 LOADING POINT ADJUSTMENT SEWING PROGRAMS ADJUSTMENT...
-
Page 4: General Features
• MANUFACTURER RESPONSABILITY JAM INTERNATIONAL is not responsible for any mishap, breaking, accidents due to the missing knowledge (or non application) of the instructions contained in the present manual. JAM INTERNATIONAL is not responsible as well for modifications, variations and/or installation of non previously authorized accessories. - Page 5 The MANUFACTURER or the SELLER offer to the Customer their Technical Service to solve any problem regarding the machine use and maintenance. Any request for service or spare parts must be forwarded to: JAM INTERNATIONAL s.r.l. Via G. Perini 2 60010 Ostra Vetere AN – ITALY...
- Page 6 SAFETY • TRAINING WARNIG! The use of the machine is allowed exclusively to authorized staff properly trained. For a proper and safe use of the machine it is necessary to have entirely read and understood the present manual and the attached instructions. •...
- Page 7 • NOT ALLOWED USE The machine JT864P-A / JT864P-A-95 has been produced to be used in the clothing industry to make seams on jeans and similar and automatic pre-creased pocket setting The machine must never be used for not allowed purposes or for purposes different from those for which it has been produced.
- Page 8 MOVING – STORAGE – DISPOSAL WARNING! Any machine transport, moving and storage operation described in this chapter must be carried out exclusively by qualified staff having suitable knowledge to operate safely forklift trucks, crane trucks and anything else necessary to the purpose •...
-
Page 9: Moving And Transportation
MOVING AND TRANSPORTATION • LIFTING WARNING : The lifting operation must be carried out with the maximum care and by AUTHORIZED STAFF only. During the lifting operations no unauthorized people are allowed to stand nearby. To lift up and to position the machine use a forklift truck of proportionate dimensions and sturdiness. Insert the forklift under the machine, be sure to take it for the entire width, fasten it well with belts or ropes and lift it paying attention that it doesn’t tilt on one side. -
Page 10: Use Of The Machine
USE OF THE MACHINE After having unpacked the machine put it in its working place in a flat and stable position. • MINIMUM DISTANCES FOR A PROPER MAINTENANCE Leave a free space of at least 50 cm on each side of the machine It is extremely dangerous to use the machine without its safety devices (emergency button, belt protection and so on). -
Page 11: Machine Description
Block the knob when the air gauge indicates a correct pressure. MACHINE DESCRIPTION • MODEL JT864P-A / JT864P-A-95 Automatic programmable pocket setter on shirts, with folding group and automatic stacker, lockstitch, controlled by touch screen panel. • SPECIFICATIONS Model... - Page 12 CONTROL PANEL BUTTON INDEX Fig 1. SCREEN 1. Number of stitches on the stitching program 2. Stitching speed 3. Program name 4. Program number 5. ---- 6. Program file 7. Bobbin counter reset 8. Bobbing counter setting 9. Stacker button 10.
- Page 13 1 STARTING Check that the emergency is over and everything is in order. Switch on the machine by turning the main switch from OFF to ON Fig. 2 Press the green button, the green screen will appear as in fig. 3 Fig.
-
Page 14: Machine Home Position
2 MACHINE HOME POSITION When the machine is in its home position the loader is set in its back position, the upper loader clamp sensor is set on ON, the upper external clamp sensor is set on ON, the internal fixed or retractable clamp sensor is set on OFF, the presser foot and the needle are lifted up. - Page 15 OPTION 2 3.3.1 Press the button “setting” , the screen will appear as in fig.10 Fig.9 3.3.2 Press the button “CN IN” 3.3.3 Select the program by using the arrows and press the button “open” 3.3.4 Repeat the operation described on 3.3.3 to insert another program 3.3.5 Press the button “Exit”...
-
Page 16: Automatic Cycle
4 AUTOMATIC CYCLE STACKER 4.1.1 On the main screen (fig.6) press the button “stacker” to choose to use it or to deactivate is (green=activated / red=deactivated) WORKING MODE 4.2.1 On the main screen press the button “automatic” (green= activated / red=deactivated) 4.2.2 Once activated the “automatic”... -
Page 17: Thread Breakage
5 THREAD BREAKAGE When the thread sensor is activated, if a needle thread breakage occurs or in case the thread is finished , the machine stops automatically. 5.1.1 Restore the thread 5.1.2 Press the button “manual movement backward” or the button “manual movement forward” to move to the chosen position, then press simultaneously the “start”... - Page 18 7 STITCHING TEST SEAM CHECKING 7.1.1 Deactivate the button “automatic” and press the button “TEST” on the main screen ( Fig. 6 ). The “TEST” button will keep pressed. 7.1.2 Press the pedal until the screen as Fig. 7 appears. The sewing clamps will lower. Pressing again the pedal the sewing clamps will lift up.
- Page 19 8 LOADING AND STITCHING TEST 8.1.1 Deactivate the button “automatic” and press the button “TEST” on the main screen ( Fig. 6 ). The “TEST” button will keep pressed. 8.1.2 Press the button “AUTOMATIC” on the main screen (Fig. 6) to enable it. 8.1.3 Once the button “AUTOMATIC”...
- Page 20 10 PROGRAM SELECTION FROM THE MACHINE MEMORY 10.1.1 Deactivate the “AUTOMATIC” button , press the pedal until the screen as in fig. 7 appears. Figura 7 10.1.2 Press the button “OPEN” . The screen as in fig. 8 appears. Figura 8 10.1.3 Select the program from the list by using the arrows.
-
Page 21: Program Copy
11 PROGRAM COPY 11.1 SELECTION OF A PROGRAM TO BE COPIED 11.1.1 Follow the procedures of chapter 10 (from 10.1.1 to 10.1.6) 11.1.2 Deactivate the “AUTOMATIC” button , press the pedal until the screen as fig. 7 appears. Fig. 7 11.1.3 Press the button “SETTING”... - Page 22 11.1.12 Press the button “SAVE” . The screen as fig. 10 will appear. 11.1.13 Press the button “EXIT” . The screen as ig. 4 will appear. 11.1.14 Press the button “RESET” , to get back to main screen as fig. 6. On the strings of the program number ( 4) and the program number ( 3 ) the new data will be displayed.
- Page 23 12 DELETE A PROGRAM FROM THE MACHINE MEMORY 12.1.1 Deactivate the “AUTOMATIC” button , press the pedal until the screen as fig. 7 appears. Fig.7 12.1.2 Press the button “SETTING” . The screen as fig. 10 will appear. Fig.11 12.1.3 Press the button “CN OUT” .
- Page 24 13 PROGRAM TRANSFER FROM THE MACHINE MEMORY TO THE USB KEY 13.1.1 Connect the USB key to the proper device 13.1.2 Deactivate the “AUTOMATIC” button press the pedal until the screen as fig. 7 appears. Fig.7 13.1.3 Press the button “SETTING” .
- Page 25 13.1.13 Press the button “RESET” , to get back to the main screen fig. 6.
- Page 26 14 PARAMETERS 14.1.1 Deactivate the “AUTOMATIC” button , press the pedal until the screen as fig. 7 appears. Fig. 7 14.1.2 Press the button “SETTING” , the screen as fig.10 will appear. Fig.10 14.1.3 Press the button “PARAMETERS” , the screen as fig.
- Page 27 15 THREAD WINDING ON THE BOBBIN 15.1 WITH MECHANICAL WINDER 15.1.1 Set the empty bobbin on the proper pin. 15.1.2 Wind the thread on the bobbin manually for a few rounds. 15.1.3 Hook the full bobbin signal lever. 15.1.4 Take off the thread from the needle. 15.1.5 Deactivate the “AUTOMATIC”...
- Page 28 16 JIG REPLACEMENT 16.1.1 Press button “ALL” on the main screen (Fig. 6). The jig components releasing screen will appear as fig. 14 Fig.14 16.1.2 Press the button “ALL” , (which becomes green ), to release the loading clamp, the external sewing clamp, the internal retractable or fixed sewing clamp 16.1.3 Take off the loading clamp by pulling it rightward.
- Page 29 17 LOADING POINT ADJUSTMENT 17.1.1 Deactivate the “AUTOMATIC” button , press the pedal until the screen as fig. 7 appears. Fig.7 Press the button “SETTING” , the screen as in fig. 10 will appear Fig.10 17.1.2 Press the button “LOADING POINT” , the screen as fig.
- Page 30 17.1.14 Press the button “RESET” , to get back to the main screen fig. 6. 18 SEWING PROGRAMS ADJUSTMENTS Before any adjustment or move of the sewing programs make a copy of the program to be modified or moved. 18.1.1 Deactivate the “AUTOMATIC” button , press the pedal until the screen as fig.
- Page 31 18.2 MOVING THE SEWING PROGRAM 18.2.1 Press the button “MODIFY PROGRAM” , the screen as fig. 18 Fig.18 18.2.2 Press the button up to the last stitch or press on the number of the stitch (check the “stitiches” string paying attention to the quantity of stitiches of the sewing program), the numerical keyboard will appear.
- Page 32 18.3 HOW TO MOVE A SEGMENT OF A STITCH ON THE SEWING PROGRAM 18.3.1 Press the button on the screen as fig. 17 up to the beginning of the segment to be moved. Fig.17 18.2.1 Press the button “MODIFY PROGRAM” , the screen as fig.
- Page 33 INTERNATIONAL www.jaminternational.it JAM INTERNATIONA s.r.l. Via G. Perini 2 – 60010 Ostra Vetere – AN – ITALIA – tel. 071 67872 – fax 071 67873 JT864P-A / JT864P-A-95 ORIGINAL INSTRUCTIONS...