Carlon HS3655 Instruction Manual

INSTRUCTION GUIDE
Motion-Activated Wall Switch HS3655
Congratulations on a wise purchase!
ENCLOSED YOU WILL FIND:
• Receiver Switch
• Wireless Motion Sensor
• Wireless Remote Control
• Screws
• Wire Nuts
• One 12-volt alkaline battery (installed)
TOOLS NEEDED:
• Phillips screwdriver
BATTERIES NEEDED (not included):
• Four AA alkaline batteries
RECEIVER SWITCH
Allows you to control an overhead light from 2 locations.
Warning: Turn off power first by removing the fuse or switching the circuit
breaker to "off." This product requires some knowledge of electrical wiring
and must be installed in accordance with the National Electrical Code (NEC) and
local codes.
Note: Not for use with existing three-way circuits.
1. Turn off power (see above).
2. Remove the faceplate of the existing wall switch.
3. Remove the existing wall switch.
4. Connect power leads to the Receiver wires by twisting the
wire nut clockwise over the ends. Push all wiring into the outlet box.
5. Slide the Control Switch on the Receiver Switch to the "On" position.
6. Replace existing faceplate.
Note: Do not use a metallic wall plate as it will decrease the operating range.
7. Restore power.
MANUAL OVERRIDE
To prevent the Receiver Switch from responding to the transmitter, slide the Control
Switch on the Receiver to the "Off" position.
Note: When changing a light bulb in the fixture controlled by the product, slide
the Control Switch on the Receiver to the "Off" position.
MOTION SENSOR INSTALLATION
Note: The motion sensor can be mounted or set
anywhere, indoors or outdoors, at a height of 0 to
10 feet from the ground. For best range and de-
tection, mount at least 6 feet from the ground.
For mounting:
A. Place adjustable mounting bracket (provided)
where desired (such as a post, tree, house)
and install top screw into key slot. Then secure
the bottom screw.
B. Slide the motion sensor down onto the bracket. Adjust the motion sensor to
the desired angle.
Note: To tighten the ball joint, use a Phillips screwdriver to turn the adjustment
screw on the bracket.
Important: The bottom cover must face downward after installation so that
moisture cannot enter.
Control
switch
ON OFF
SET-UP
1. Remove the wireless motion sensor
bottom cover by pressing inward on
the latch.
2. Pull tab to bring out the battery holder
and install four AA alkaline batteries.
Be sure that the battery (+) and (-) ter-
minals match the (+) and (-) contacts
shown in the battery compartment.
3. The day/night switch should be in the
day/night mode.
4. The timer (or left) switch should be in
the leftmost position (6 s) for test. With
the switch in this position, the light
will turn off approximately 6 seconds
after turning on. This will allow quick
testing of the motion sensor with the
light control.
5. Replace bottom cover.
TEST
1. Walk through the coverage area. Note when the light turns on. If the coverage
area needs to be changed, adjust the motion sensor for improved coverage.
Retighten the ball joint screw.
2. After completing the test, determine the amount of on-time you want for the
light to stay on after motion is detected. The timer switch allows the choices of
10 minutes (rightmost switch position) or 3 minutes (center switch position).
3. Also decide if you want the light control to turn on during the day and night
when motion is detected or just at night. Set the Detect switch to the left for
night only operation and to the right for day/night operation.
4. Close the bottom cover.
DETECTION ZONE
Motion is detected in a 60' x 140˚ range
which will be over 4396 sq. feet. The
mounting bracket can be adjusted to
customize the detection zone.
Note: As with most motion detection
devices, pets or other animals may
activate the unit. Also, walking in a
straight line towards the motion sensor
may reduce operating range. Walking
across the detection field provides the
maximum operational range.
REMOTE CONTROL
Press the "on" or "off" button to override
the system and turn light on or off.
TO REPLACE REMOTE CONTROL
BATTERY
Remove the top screw from the back of
the remote control. Lift off the back cov-
er, remove old battery and insert new
battery according to the (+,-) placement
guides. Replace the back cover along
with the screw. The remote control will
now be ready to operate.
Only
Only
COVERAGE AREA
Top View
60'
140º
MOUNTING BRACKET ADJUST-
MENT
Up and Down
Left Right
Side to Side