Subscribe to Our Youtube Channel
Related Manuals for Automatic LPM200
Summary of Contents for Automatic LPM200
- Page 1 LPM200 Stationary Roller Mill Operator, Parts & Installation Manual 405-0525 Rev A Page 1 of 16 4/5/16...
- Page 2 Misuse and neglect will only cause unnecessary expense and dissatisfaction. This manual is written as a guide for owners and operators of the Automatic LPM200 model roller mill. Read it carefully and follow the suggestions made. Keep this manual in a convenient place for quick, easy reference, and use it whenever questions arise.
- Page 3 Steps should be taken to assure the safety of the operator, and any other people in the area. Automatic Equipment strongly recommends that no person be permitted to operate this mill without a thorough understanding of how the machine works and the precautions to be observed.
- Page 4 Safety SAFETY PRECAUTIONS - DURING OPERATION 1. DO NOT wear loose-fitting clothing that may catch in moving parts. 2. Children should not be permitted in areas where machinery of this nature is operating. 3. DO NOT operate this machine until you are sure everyone is clear of the area. 4.
- Page 5 ROLLER MILL MAINTENANCE AND OPERATION Automatic Grain roller mills are manufactured from the best materials and workmanship available - each has been tested and properly adjusted at the factory before shipping. Simple adjustments and minimum maintenance have been emphasized. Reasonable care and operation will assure many years of trouble-free service.
-
Page 6: Table Of Contents
(Usually Grade 5). Repair parts can be ordered through your nearest dealer. If there is no dealer in your area, call Automatic Equipment Manufacturing at (402) 385-3051. Parts Index Basic Assembly ..................7/8 Chain Drive .................... -
Page 7: Basic Assembly
Basic Assembly continued to page 8 405-0525 Rev A Page 7 of 16 4/5/16... - Page 8 Basic Assembly cont’d Ref. Ref. Part No. Description Part No. Description 100-0096 ........Front End Plate 200 206-0083 ........ #41 x 64 P. Chain 200 62-0934 ....... 1 3/8 Pillow Blk Brg 200 (Incl. Conn. Lnk.) 209-0001 ......1 3/8 Bearing Insert 200 210-0004 ..........
-
Page 9: Chain Drive
Chain Drive Ref. Part No. Description 61-1675 ....................Support w/ Wld Nut Chn Shld 100-0058 ......................5/16 x 1 1/2 Sq. Key 204-0009 ....................5026 x 1 3/8 w/ Grip Hub 201-0271 ................5/16 - 18 x 3/8 Socket HD Set Screw 201-0269 ................ -
Page 10: Belt Drive
Belt Drive Ref. Part No. Description 61-1679 ......................Brkt., Belt Shield 200 205-0008 ...................... 2BK120H Sheave, 200 205-0047 ......................H 1 3/8 Bushing, 200 101-2532 .......................Filler Plate, Belt Shield 102-1295 ......................Strip Motor Support 201-0272 ......................5/16 - 18 Thumb Screw 61-1608 ......................Back Belt Shield 200 251-0030 ........................ -
Page 11: Auger Base
Auger Base (Optional) continued to page 12 405-0525 Rev A Page 11 of 16 4/5/16... - Page 12 Auger Base (Optional) cont’d Ref. Part No. Description 101-2507 ...................Seal Ch. Side Aug. Base #200 61-1683 ......................Aug. Out Base #200 201-0278 ..................3/8 - 16 x 3/4 Cup PT. Set Screw 225-0015 ....................6” Ring Clamp Set, 200-400 61-1602 ........................Leg, Feed Meter 100-0464 .....................
-
Page 13: Hopper Assembly
Hopper Ref. Part No. Description 61-1684 ......................Magnetic Grate 200 101-3426 ......................Corner Bolt-In 200 202-0018 ....................... 3/8 - 16 Wing Nut 102-1231 ......................Stop, Hopper Gate 101-2450 ........................Brkt. Door Lock 61-1682 ......................Hopper Wldm’t 200 61-1672 ....................Gate Wldm’t, 200 Hopper * Available for hoppers made prior to 1986. -
Page 14: Frame
Frame Ref. Part No. Description 61-1671 .......................Motor Mount, #200 61-1623 ........................ADJ. Rod Motor 61-1695 (optional) ....................Downspout #200 201-0278 .................3/8 - 16 x 3/4 SQ. HD KN. C.P. Set Screw 61-1677 .........................Frame Skid, #200 405-0525 Rev A Page 14 of 16 4/5/16... - Page 15 Troubleshooting This section is a condensed chart to help you remedy problems if unsatisfactory operation occurs. If you are unable to determine and correct the trouble, consult your authorized dealer. TROUBLE CAUSE REMEDY Excessive Roll Wear 1. Overfeeding with excess Keep rolls “hungry”.
- Page 16 All rolls are guaranteed for life against breakage. This warranty does not apply to any part of an Automatic roller mill which has been subject to misuse, neglect, alteration, accident, or damage caused by fire, flood, or other damage beyond control of the manufacturer.
Need help?
Do you have a question about the LPM200 and is the answer not in the manual?
Questions and answers