Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
- Weight ± 5.05 kg Product information is subject to change without notice. 43PFT5102 For detailed product information,please visit • without TV stand: www.philips.com/support Width 968.2 mm - Height 562.4 mm - Depth 63.6mm - Weight ± 8.45 kg • with TV stand: Display Width 968.2 mm - Height 624.8 mm - Depth 193.9...
Page 4
Dolby Digital, Dolby Digital Plus, DTS 2.0 + Digital • Analogue video playback : SECAM, PAL Out™, MPEG-1/2/2.5 Layer I/II/III (includes MP3), • Digital video playback : MPEG2 SD/HD WMA (v2 to v9.2), WMA Pro (v9/v10) (ISO/IEC13818-2), MPEG4 SD/HD (ISO/IEC 14496-10) •...
3.2 Assembly/Panel Removal 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand. 2. Take the stand bracket out from the set. 3.2.2 IR board Control Unit Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! Remove all the fixation screws [1],and connector [2] from the IR board control unit.
Page 8
3.2.3 Keyboard Control Unit Release the connector [1] from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! Remove all the fixation screws from the keyboard control panel [2] and take it out from the Back cover When defective, replace the whole unit.
Page 9
3.2.5 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
Page 10
3.2.9 LCD Panel 1. Remove the SSB as described earlier. 2. Remove the PSU as described earlier. 3. Remove the keyboard control panel as described earlier. 4. Remove the stand bracket as described earlier. 5. Remove the IR/LED as described earlier. 6.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 12
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 13
Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return” button. Do not allow the display to time out between entries while keying the sequence. After entering the Factory mode, we can see many items displayed, use the UP/DOWN keys to display the next/previous menu items Factory mode overview How to Exit the Factory mode Use one of the following methods:...
Page 14
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. ...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). 4. Switch off the TV and Insert the USB memory stick that contains the software update files in one of the TV’s USB 2.0 ports. Note: It contains USB3.0 port, if connect on it, the software may can’t be detected.
Page 16
Step 2: F/W Upgrade 1. Press [Quick settings], then Choose [Update Software] in the Settings menu 2. Choose [Local Updates], then press OK. Select the file that you downloaded and press OK 4. Choose [Update], then choose [Start] on following step...
Page 17
5. Upgrade in progress Step 3: Check the SW version 1. After burning software, TV will restart. 2. Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 18
You can read the error buffer in below ways: • On screen via the SAM/CSM (if you have a picture). Example: – ERROR: 000 000 000 000 000: No errors detected – ERROR: 013 000 000 000 000: Error code 13 is the last and only detected error –...
Page 19
Press the following key sequence on a standard RC transmitter: “062596” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT BOM# Panel Type Display Code 32PHT5102/98 TPT315B5-1A058.L S24C XM 32PHT5102/98 TPT315B5-1A058.L S28A 32PHT5102/79 TPT315B5-1A058.L S24C XM...
6. Circuit Descriptions 6.1 Introduction The TPM17.1A LA is a new chassis launched in AP in 2017. The whole range is covered by MT5800WUEJ platform. The major deltas versus its predecessor support NTSC;PAL-M; PAL-N AND ISDB-T with also multi-media, CEC,ARC,MHL, SPDIF functionality. The TPM17.1A LA chassis comes with the following stylings: series xxPHT5102/xx ...
Page 21
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 22
PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller). PSDL stands for a Power Supply for Direct-view LED backlight with 2D-dimming. 6.3 DC/DC Converters The on-board DC/DC converters deliver the following voltages(depending on set execution): •...
Page 23
6.3.2 Power layout SSB FB712,+5 U712,3V3SB U705,AVDD3V3 FB702, +5V_SW FB603, PVDD L703, Vcck D704,LNB Power U702, Tuner 3.3V Power SSB Top View...
Page 24
U707, +1.8V L702, DDRV Power SSB Bottom View...
Page 25
6.4 Front-End Analogue and DVB-C,DVB-T2; reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER EU ST42CS-2-E • SCALER MT5800WUEJ BGA-597 Processor Below find a block diagram of the front-end application for DVB-C part. MT5800 6.4.2 DTB-T2 part The Front-End for DVT part consist of the following key components:...
Page 26
6.5 HDMI Refer to below for the application. The following HDMI connector can be used: • HDMI 1: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/MHL • HDMI 2: HDMI input ( TV digital interface support HDCP) with digital audio/PC DVI input/ARC •...
Page 27
OVERVIEW: The MediaTek MT5800WUEJ family consists of a DTV front-end demodulator, a backend decoder and a TV controller and offers high integration for advanced applications. It integrates a transport de-multiplexer, a high definition video decoder, an audio decoder, a two-link LVDS transmitter, a V-by-One transmitter, and an NTSC/PAL/SECAM TV decoder with a 3D comb filter (NTSC/PAL).
9. Styling Sheets 9.1 5102 series 32" Pos NO. Description Remark 0030 BEZEL 0040 REAR COVER 0064 PCB_FRAME 050R STAND BASE R 050L STAND BASE L 1050 PANEL 1176 Remote Control No Display 1053 MIAN BOARD 1054 POWER BOARD 1056 IR BOARD 1057 KEY BOARD...