The purpose of this manual is to provide necessary information for product installation, operation, and maintenance. Electronic versions of this manual, as well as data sheets and other information can be found on: xylem.com/jabsco MANUAL CONTENTS Page Kit Contents & Pump Mounting Installation Instructions Controls &...
Quiet Flush E2 Kit Contents Quiet Flush E2 Electric Toilet Assembly • Seat and Lid • Touch pad control panel and control box • Solenoid valve kit (Fresh water version) • Intake rinse pump kit (Raw water version) • White 3/4” (19mm) inlet hose, 6ft (1.8m) •...
Applications • Offer up the toilet in the selected position and, using the holes in the base as a guide, mark the positions Jabsco Quiet Flush electrically operated marine toilets can for the 3 bolt holes on the mounting surface. Remove be installed in both power and sailing craft, either above the toilet and drill 3 vertical holes of 5/16”...
Page 5
HAZARD RISK: Through-Hull Fittings – FOLLOW THESE INSTRUCTIONS! If the installation of the toilet results in it being connected to ANY through-hull fitting that may possibly be below the waterline at ANY time, whether when the craft is at rest, underway and heeling or rolling or pitching, you must install the toilet in accordance with these Installation Instructions.
Page 6
Fresh Water Rinse Pipework Hardware Requirements: • A ‘T’ piece that fits your boat’s pressurized water system pipework with a 1/2” (13mm) nipple going to the solenoid valve. CAUTION: Turn off power to the water pressure system pump, and open cold water faucet to depressurize the system.
Discharge Pipework – 4 Options Option 1: Toilet below the waterline and discharging overboard • A 1” (25mm) or 1.5” (38mm) vented loop MUST be fitted, Jabsco part number 29015-0020 1” (25mm) or 29015-0010 1.5” (38mm). • Run the outlet hose from the non-return valve assembly to form a loop which is at least 8” (20cm) above the highest possible waterline, and fit the vented loop at the highest point Option 2: Toilet always above the heeled waterline and discharging overboard •...
Page 8
Screw into place with four counter sunk head screws Fascia panel Battery Orange Waste pump (+ve and -ve) Rinse pump Blue or solenoid Black 2 x common negative Black 6 pin plug for two button control panel • Connect the boat’s positive (+) feed to the red DC supply (+) input lead of the control box, and your boat’s negative (—) return to the black DC supply (—) output lead of the control box.
Page 9
Securing the Toilet Base & Installation of Motor Support Note: To help with the installation, the discharge pump assembly may be removed prior to completing this task. Bolt down the toilet base using the selected hardware (page 4). Tighten all fixings securely, if you are not using self locking nut, use nut locking compound.
Rinse Options 1. Fresh Water 2. Raw Water 1. Quiet Flush Series are supplied with a combined solenoid valve and double non-return valve for connection to any existing pressurized water system capable of 3 GPM or more. The double non-return valve prevents back-flow from the toilet into the potable water system.
Servicing Instructions Jabsco Quiet Flush electric toilets do not normally require maintenance during the season, provided that they are winterized in the autumn. • Regularly check all fastenings for tightness and leaks. HAZARD RISK: Leaks – REPAIR LEAKS IMMEDIATELY! If the toilet is connected to ANY through-hull fittings and, if the toilet or the pipework develops a minor leak, it can suddenly become a major leak that allows water to flood in, causing the craft to sink, which may result in loss of life.
Page 12
Filling system with non-toxic anti-freeze CAUTION: If using antifreeze to winterize the toilet system, use only Propylene glycol (pink marine/ RV antifreeze). • Flush enough antifreeze to ensure the antifreeze reaches any directional valves (if equipped) and the black water holding tank(s).
Spare Parts HOSE (NOT SHOWN) 4a 1” TO 1.5” DISCHARGE HOSE ADAPTER (25mm to 38mm) 27c MOTOR SUPPORT (NOT SHOWN) Part name Qty. Raw Part Number Seat and cover (compact bowl) 29097-1000 Seat and cover (slow close, regular bowl) 58104-2000 Hinge kit - (1 pair) Compact seat 29098-1000 Hinge kit - (1 pair) Regular slow close...
Page 14
Base O-ring 44101-1000 Base cover 38508-1000 Base cover screw 91045-0441 Base mounting feet 38510-1000 Discharge pump clip 38504-1000 Toilet base See kits O-ring See kits Waste pump housing 38500-1000 O-ring See kits Joker valve 44106-1000 Discharge port - straight See kits Discharge port - 90º...
Warranty XYLEM LIMITED WARRANTY WARRANTS THIS PRODUCT TO BE FREE OF DEFECTS AND WORKMANSHIP FOR A PERIOD OF 1 YEAR FROM DATE OF MANUFACTURE. THE WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, GUARANTEES,...
Page 16
2012/19/EU 1.1 End of life product disposal Handle and dispose of all waste in compliance with local laws and regulations. Waste Electrical & Electronic EU only: Correct disposal of this product — WEEE Directive on waste electrical Equipment (WEEE) and electronic equipment. This marking on the product, accessories or literature indicates that the product should not be disposed of with other waste at the end of its working life.
Page 17
märgistus, tähendab see seda, et toodet ei tohi elutsükli manna sem hlýst af óhindraðri förgun úrgangs skaltu aðskilja lõppedes kõrvaldada koos muude jäätmetega. þessa hluti frá öðrum úrgangi og endurvinna þá á ábyrgan hátt til að stuðla að sjálfbærri endurnýtingu hráefna. Jäätmete kontrollimata kõrvaldamise tõttu tekkida võivate keskkondlike või terviseseisundi kahjude vältimiseks eraldage Raf- og rafeindatækjaúrgangi er hægt að...