Table of Contents
Advertisement
Quick Links
Legend Network Video Recorders
Quick Guide
Version: V1.04
Thank you for purchasing our product. Contact your local dealer if you have any
questions or feedback. No part of this manual may be copied, reproduced, translated,
or distributed in any form or by any means without prior consent in writing from our
company. Contents of this manual are subject to change without prior notice. No
statement, information, or recommendation in this manual shall constitute formal
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Inaxsys LEGEND
Summary of Contents for Inaxsys LEGEND
- Page 1 Legend Network Video Recorders Quick Guide Version: V1.04 Thank you for purchasing our product. Contact your local dealer if you have any questions or feedback. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from our company.
-
Page 2: Safety Information
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class www.inaxsys.com... -
Page 3: Lvd/Emc Directive
Battery Directive-2013/56/EC Battery in the product complies with the European Battery Directive 2013/56/EC.For proper recycling,return the battery to your supplier or to a designated collection point. Default IP, Username and Password Default IP address: 192.168.1.30 www.inaxsys.com... -
Page 4: Disk Installation
Note: The three dotted lines (for illustration) divide four sets of screw holes. Do not install across the lines. An 8 HDD device has two mounting plates. Take out the mounting plates, secure all disks on the www.inaxsys.com... - Page 5 Make sure the disk faces the correct side for installation. Choose an option as appropriate. Use a 1# or 2# screwdriver as needed. All photos are only for illustration. 1 or 2 HDD Installation Loosen screws on the rear panel and both sides. Remove the cover. www.inaxsys.com...
- Page 6 Loosen screws on the disk the disk. halfway. Slide the disk in the screw holes. Tighten the screws. Connect the power cable to the Connect the data cable to the motherboard. motherboard. Put the cover back in place and tighten the screws. www.inaxsys.com...
- Page 7 Loosen screws on the rear panel. Press with both thumbs and slide open the cover. Loosen screws on both sides. Take out the mounting plate. Secure disks on the mounting plate Place the mounting plate back in and tighten the screws. place. www.inaxsys.com...
- Page 8 Tighten screws on both sides to Connect power and data cables to secure the mounting plate. the disk. Connect the data cable to the Put the cover back in place. motherboard. Tighten screws on the rear panel. Take Mounting Bracket as an Example www.inaxsys.com...
- Page 9 Install all disks in the same way and push gently till it clicks in and then install the front panel. position. Ports, Interfaces and LEDs The ports, interfaces, connectors, power on/off switch and LED indicators may vary with device model. See the following two examples. www.inaxsys.com...
- Page 10 PoE ports Power on/off HDMI output DC power VGA output Network Audio input RS232 (for maintenance) eSATA interface Alarm input/output CVBS output AC power Network Power on/off Grounding 12V DC output RS485 Audio out/input HDMI output VGA output HDMI output www.inaxsys.com...
- Page 11 Blinks red: Rebuilding array. Startup Verify installation and cable connection are correct. Connect to power and then turn on the power on/off switch (if applicable). Follow the wizard to complete the basic setup after the NVR starts up. www.inaxsys.com...
-
Page 12: Live View
QR code, please contact your local dealer. Shutdown Use the Shutdown menu instead of by disconnecting power or turning off the power on/off switch. A sudden power failure may cause device damage and loss of data. www.inaxsys.com...
Need help?
Do you have a question about the LEGEND and is the answer not in the manual?
Questions and answers