Advertisement
Quick Links
Advertisement
Related Manuals for HUA YI ELECTRONICS HY3000-2 Series
Summary of Contents for HUA YI ELECTRONICS HY3000-2 Series
- Page 1 USER’S MANUAL DC REGULATED POWER SUPPLY...
- Page 2 DC POWER SUPPLY BRIEF INTRODUCTION: HY3000-2、HY3000-3、HY5000-2 series variable DC power supplies are very stable, regulated multiple output DC power supplies allowing continuous adjustment of both the output voltage and current levels. The HY3000-2、HY3000-3、HY5000-2、HY6000-2 series have dual LED displays; It has three outputs, with one output being fixed at 5V.
- Page 3 MODELS: HY3002 -2 HY3003 -2 HY3005 -2 HY3002 -3 HY3003 -3 HY3005 -3 MODEL HY3002D-2 HY3003D-2 HY3005D-2 HY3002D-3 HY3003D-3 HY3005D-3 HY3002F-2 HY3003F-2 HY3005F-2 HY3002F-3 HY3003F-3 HY3005F-3 OUTPUT 2×0-30V 2×0-30V 2×0-30V 2×0-30V 2×0-30V 2×0-30V VOLTAGE OUTPUT 2×0-2A 2×0-3A 2×0-5A 2×0-2A 2×0-3A 2×0-5A CURRENT FIXED...
-
Page 4: Technical Parameter
TECHNICAL PARAMETER 1.1 Input voltage: 104~127V AC (60Hz), or 207~253V AC (50Hz) 1.2 Dual adjustable power supply 1.2.1 Line regulation: CV≤0.01%+2mv CC≤0.2%+2mA 1.2.2 Load regulation: CV≤ 0.01%+3mv(I≤3A) CC≤0.2%+3mA(I≤3A) CV≤ 0.01%+5mv(I>3A) CC≤0.2%+5mA (I>3A) 1.2.3 Ripple and noise: CV≤0.5mVr.m.s(I≤3A) CC≤3mAr.m.s(I≤3A) CV≤1.0mVr.m.s(I>3A) CC≤6mAr.m.s(I>3A) 1.2.4 Protection: constant current or short-circuit protection 1.2.5... - Page 5 Operation 2.1 Front panel controls (1) Voltage and current indication for master output. (2) Voltage or current display selector for master output. (3) Voltage or current display selector for slave output. (4) Voltage and current indication for slave output. (5) Voltage adjustment of master output. (6) Current adjustment of master output.
- Page 6 (15) Positive output terminal of master output. (16) Ground connection terminal of case. (17) Negative output terminal of master output. (18) Positive output terminal of slave output. (19) Ground connection terminal of case. (20) Negative output terminal of slave output. (21) Mains power on/off switch.
- Page 7 Output current less than 10A),switch on the power ON/OFF switch and adjust controls 6 & 8 anti-clockwise to the minimum position. Adjust controls 5&7 to give the desired output voltage and then connect output terminals 15 with 17 and 18 with 20 respectively. Move switches 2&3 to the current display position.
- Page 8 master output. 2.2.2.3 In series mode, terminals 17&18 should be connected together with a thick conductive wire to prevent damage to the unit in the event of an overload. 2.2.2.4 In series mode, remove any connection between the master or slave negative terminals and the ground connection terminals otherwise it is possible to short-circuit the slave output.
- Page 9 ACCESSORIES 4.1 Power cord----------------------------one piece 4.2 Instruction manual-------------------one piece...
Need help?
Do you have a question about the HY3000-2 Series and is the answer not in the manual?
Questions and answers