Advertisement
Tetra
Power Supply GEPS24-100U-GLX2
®
RISK OF ELECTRIC SHOCK
• Disconnect power at fuse box or circuit breaker before servicing
or installing product.
• Properly ground Tetra
power supply.
®
• AC input connections shall be suitably enclosed. The power supply
shall be enclosed or made inaccessible to users during normal use.
RISK OF FIRE
• Minimum power supply spacing to other power supply or other
heat producing component shall be at least 4" (101.6 mm) from
side to side and 1" (25.4mm) from end to end.
• Use only approved wire for input/output connection. Minimum
size 18 AWG (0.82 mm
).
2
• Follow all local codes.
• Application considerations potentially requiring additional spacing
include high ambient temperature seen by the power supply, poor
contact with a heat dissipating material, inadequate ventilation, or
direct exposure to sun.
RISK INJURY
• While performing installations described, gloves, safety
glasses or goggles should be worn.
Power Supply Installation
Mount the power supply. Mounting
1
the power supply base directly to
a thermally conductive installation
surface can improve thermal
performance.
NOTE: All electrical connections
should be suitably protected
from mechanical damage and the
environment. Seal all connections
exposed to water with electrical
grade self-hardening silicone.
NOTE: For installation in Canada, a disconnect switch of appropriate rating needs to be placed within 29.5 feet
FOR UL ONLY
(9 meters) of primary side of the power supply. The switch voltage rating shall not be less than the branch circuit
voltage. The switch must also support twice the amount of input current.
NOTE: When installing power supply, connect to the appropriate sized building breaker or disconnect device for line,
FOR UL ONLY
neutral and ground connections, in accordance with National Electric Code (NEC) Article 600 and all local regulations.
OPTIONAL
A Weather Box (GEXNWB2) may be used to house and seal Class 2
connections.
A) Insert wire connectors into weather box. Fill with electrical grade
silicone and close box.
B) Secure the weather box using a #6 or #8 (M2 or M3) screw.
WARNING / AVERTISSEMENT
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l'alimentation électrique à la boîte de fusibles ou au disjoncteur avant
l'entretien ou l'installation du produit.
• Assurez-vous de correctement mettre à terre le bloc d'alimentation Tetra
• Les connexions d'entrée CA doivent être convenablement enfermées. Le bloc
d'alimentation doit être enfermée ou rendue inaccessible aux utilisateurs
pendant l'utilisation normale.
RISQUES D'INCENDIE
• L'espacement minimal du bloc d'alimentation par rapport à un autre bloc
d'alimentation ou aux autres composants produisant de la chaleur doit être
au moins 4" (101,6 mm) de chaque côté et 1" (25,4 mm) de bout en bout.
• N'utilisez que des fils approuvés pour les entrées/sorties de connexion.
Taille minimum 18 AWG (0.82 mm
• Respectez tous les codes locaux.
• Certaines applications pourraient requérir un espacement additionnel, p.
ex. une température ambiante élevée autour du bloc d'alimentation, un
mauvais contact avec une matière dissipatrice de chaleur, une ventilation
inadéquate ou une exposition directe au soleil.
CAUTION / ATTENTION
RISQUES DE BLESSURE
• Lors de l'exécution des installations décrites, des gants, des lunettes
de sécurité ou des lunettes de protection doivent être portées.
Input
Black or brown
wires
White or blue
(neutral)
AC line
Connect the AC line to the black
2
or brown (line) and white or
blue (neutral) input wires of the
power supply using suitable wire
connectors.
WARNING
RISK OF ELECTRIC SHOCK
AC input connections shall be
suitably enclosed. Optionally,
the GEPSJB60 may be used for
this purpose.
2
Installation Guide
).
2
Red (+)
(line)
Output
wires
Connect the supply wire that is
3
attached to the Tetra LED System
to the red (+) and black or blue (-)
output wires of the power supply
as outlined in the "Electrical
Connections" section of your LED
system's Installation Instructions.
NOTE: To avoid overloading this
power supply with LED modules,
please refer to the specific module
loading guides.
A
B
.
®
To Tetra LED System
Black or blue (-)
Weather box
can be painted
Light engine
Advertisement
