Sony HT-ST5000 Startup Manual page 2

3
Setting up the remote control
設定遙控器
4
Turning on the TV
開啟電視機的電源
5
Turning on the system
開啟系統的電源


Connect the AC power cords (mains leads) of the Bar Speaker and
subwoofer.
 Press  (power) on the remote control of the system.
The front panel display lights up.

Confirm that the power indicator of the subwoofer is lit in green.
If not, refer to "Subwoofer" of "Troubleshooting" in the Operating Instructions
(separate document).

Turn on the connected device.
6
Performing Easy Setup
進行簡易設置
////
HOME

Press HOME on the remote control of the system.
The Easy Setup screen is displayed on the TV screen.
If the Easy Setup screen does not appear, use the remote control of the TV to switch
the TV input to that for the HDMI IN jack to which the system is connected.
 Press /// to select an item as instructed on the TV screen, and then
press to perform Easy Setup.

Once [Easy Initial Settings are complete.] appears, select [Finish].
Tip
• On-screen instructions are displayed in the language you selected in this step.
• For details on the network connection, refer to "Listening to Music/Sound Using the Network Function"
in the Operating Instructions (separate document).
• For details on Chromecast built-in, refer to "Using Chromecast built-in" in the Operating Instructions
(separate document).
Power
電源
/
Power indicator
(green)
Front Panel 電源指⽰燈
前方面板 （綠色）


連接主動式揚聲器系統和主動式重低音揚聲器的交流電源線。

按下系統遙控器上的（電源）。
前顯示面板亮起。

確認主動式重低音揚聲器的電源指示燈亮綠色。
否則，請參閱使用說明書（另外的文件）中"故障排除"的"主動式重低音揚聲器"。

開啟外接裝置。

按下系統遙控器上的HOME。
電視機螢幕上顯示簡易設置畫面。
如果沒有出現簡易設置畫面，請使用電視機的遙控器，將電視機輸入切換為系統所連接
HDMI IN插孔的輸入。

按下///依照電視機螢幕指示選擇項目，然後按下 以執行簡易設置。

一旦顯示[簡易初始設置完成。]，請選擇[完成]。
提⽰
• 畫面上的說明是以您在此步驟所選擇的語言顯示。
• 如需網路連線的詳細資訊，請參閱使用說明書（另外的文件）中的"使用網路功能聆聽音樂/聲音"。
• 如需Chromecast built-in的詳細資訊，請參閱使用說明書（另外的文件）中的"使用Chromecast
built-in"。
7
Listening to the sound
聆聽聲音
INPUT +/–
////
HOME
SW  +/–  +/–
To listen to the audio of the TV

Select the desired program using the remote control of the TV.
The screen switches to the television broadcast screen and the TV audio is output
from the system.
If the sound of the TV does not output from the system, press INPUT +/− on the
remote control of the system until "TV" appears in the front panel.
 Adjust the volume.
Adjust the volume by pressing  +/− on the remote control of the system.
Adjust the volume of the subwoofer by pressing SW  +/− on the remote control of
the system.
For details on the sound quality adjustment, refer to "Selecting the Sound Effect" in the
Operating Instructions (separate document).
聆聽電視機的聲音

以電視機的遙控器選擇所要的節目。
畫面切換為電視廣播畫面，而且系統輸出電視機的聲音。
如果系統沒有輸出電視機的聲音，請按下系統遙控器上的INPUT +/-，直到"TV"出現在前
方面板中。

調整音量。
按下系統遙控器上的 +/-，以調整音量。
按下系統遙控器上的SW  +/-，以調整主動式重低音揚聲器的音量。
如需音質調整的詳細資訊，請參閱使用說明書（另外的文件）中的"選擇音效"。
Setup completed! Enjoy! Refer to the Operating Instructions (separate document) for
what you can do with the system and the network settings.
設定完成！歡迎享受！ 請參閱使用說明書（另外的文件）中的系統功能和網路設定。
Troubleshooting
No TV sound is output from the system, or no picture is displayed on the
TV.
• Press INPUT +/− on the remote control of the system repeatedly until "TV" appears in the front panel display
on the system.
• Make sure that the input and output of the HDMI jacks on the system are correct.
• Disconnect the cables that are connected between the TV and the system, then connect them firmly again.
Disconnect the AC power cords of the TV and the system from the AC outlets (mains), then connect them
again.
• Depending on the order in which you turn on the TV and the system, the system may enter muting mode
and "Muting" may appear in the front panel display. In this case, turn on the TV first, then the system.
• When the TV and the system are connected via an HDMI cable, enable the control for HDMI function on the
TV. For details on the TV's settings, refer to the operating instructions supplied with the TV. For more
information about the control for HDMI function, refer to the Operating Instructions (separate document).
• Check the sound setting of the TV. When the TV is set to output the sound from the TV speakers, change the
setting to output the sound from the external speakers.
No picture or sound from the device connected to the system is output.
• Press INPUT +/− on the remote control of the system repeatedly until the input connecting the desired
device appears on the front panel display of the system.
• Make sure that the input and output of the HDMI jacks on the system are correct.
• Disconnect the cables connected to the system, and then connect them again. Make sure that the cables are
firmly inserted.
The TV remote control does not work.
• When the Bar Speaker obstructs the remote control sensor of the TV, the TV remote control may not work. In
that case, set [IR-Repeater] to [On]. You can control the TV with the remote control of the TV. For details, refer
to "Sending the Remote Signal to the TV via the Main Unit" in the Operating Instructions (separate
document).
No sound or only a very low-level sound is heard from the subwoofer.
• Press SW  +/− on the remote control of the system to increase the volume of the subwoofer.
If the problem is not solved even though you have tried the measures above, refer to
"Troubleshooting" in the Operating Instructions (separate document).
Home menu
主選單
To enjoy an input device other than the TV

Press HOME.
The home menu appears on the TV screen.
If the home menu does not appear, use the remote control of the TV to switch the TV
input to that for the HDMI IN jack to which the system is connected.
 Press /// to select the desired input on the home menu, and then
press .
For details, refer to "About the Home Menu" in the Operating Instructions (separate
document).
若要使用電視機以外的輸入裝置

按下HOME。
電視機螢幕上出現主選單。
如果沒有出現主選單，請使用電視機的遙控器，將電視機輸入切換為系統所連接HDMI IN插
孔的輸入。

按下///在主選單上選擇所要的輸入，然後按下 。
如需詳細資訊，請參閱使用說明書（另外的文件）中的"關於主選單"。
故障排除
系統沒有輸出電視機聲音，或是電視機沒有顯⽰圖像。
• 重複按下系統遙控器上的INPUT +/-，直到"TV"出現在系統的前顯示面板中。
• 確定系統上的HDMI插孔輸入和輸出正確。
• 請中斷連接電視機與系統的連接線，然後再次穩固連接它們。 請從交流電插座拔出電視機與系統的交流電源
線，然後再次連接它們。
• 視您開啟電視機和系統的順序而定，系統可會進入靜音模式，而且前顯示面板中可能會出現"Muting"。在此狀
況下，請先開啟電視機，然後再開啟系統。
• 透過HDMI連接線連接電視機和系統時，在電視機上啟用HDMI控制功能。如需電視機設定的詳細資訊，請參閱電視
機附帶的使用說明書。如需HDMI控制功能的詳細資訊，請參閱使用說明書（另外的文件）。
• 檢查TV的聲音設定。當TV設定為從TV揚聲器輸出聲音時，將設定更改為從外接揚聲器輸出聲音。
連接系統的裝置沒有輸出圖像或聲音。
• 重複按下系統遙控器上的INPUT +/-，直到連接所需裝置的輸入出現在系統的前顯示面板中。
• 確定系統上的HDMI插孔輸入和輸出正確。
• 將連接系統的連接線拔出，然後重新連接。確定連接線牢固地插入。
電視機遙控器無效
• 當主動式揚聲器系統阻礙電視機的遙控器感應器時，電視機遙控器可能無效。在此狀況下，請將[IR-Repeater]
設為[開]。您可以使用電視機的遙控器控制電視機。如需詳細資訊，請參閱使用說明書（另外的文件）中的"透
過主機將遠端訊號傳送到電視機"。
主動式重低音揚聲器沒有發出聲音或聲音非常微弱。
• 按下系統遙控器上的SW  +/-提高主動式重低音揚聲器的音量。
如果嘗試以上措施後問題仍然沒有解決，請參閱使用說明書（另外的文件）中的"故障排除"。