Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Chamberlan PowerLift Plus CS100EVO
- Page 1 chamberlaindiy.com.au chamberlaindiy.co.nz CS100EVO Sectional Garage Door Opener Installation and Operating Instructions Owners Copy: SAVE THESE INSTRUCTIONS for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY...
-
Page 2: Table Of Contents
WARNING! START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service, provided it is installed and operated in strict accordance with the instructions in this manual. -
Page 3: Before You Begin
BEFORE YOU BEGIN: 1. Look at the wall and ceiling above the garage door. (The opener and header bracket must be securely fastened to structural supports.) 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required. -
Page 4: Carton Inventory
CARTON INVENTORY Your garage door opener and rail are packed in a single carton. The PowerLift Plus CS100EVO opener cartons contain the opener, the rail, its fitting hardware and accessories. (1) Opener (9) Hardware bag (2) Hand held transmitter x 2... -
Page 5: Tools Required
TOOLS REQUIRED Drill Bits HARDWARE PROVIDED (1) Clevis pin 80 mm (Section 13) (2) R clip (Section 13) (3) Hexagonal head screw (Sections 15 & 17) 1 (1x) 3 (4x) 2 (1x) 4 (4x) 5 (4x) (4) Nut M8 (Sections 15 & 17) (5) Flat washer M8 (Sections 15 &... -
Page 6: Control Panel
CONTROL PANEL (located under the cover at the rear of the opener) 1. External Accessory Power: 30 Vdc 50 mA available for universal receiver (not active in Low standby mode). 2. Terminal Block: used for external accessories (see chart below). Function Colour Polarity Comment E-Serial port... -
Page 7: Assembly
ASSEMBLY SECTION ASSEMBLING THE 4 PIECE SEGMENTED RAIL The segmented rail is largely preassembled and consists of 4 parts. The carriage, push rod, release handle, the guide pulley and the lintel bracket with belt tensioner are in the front part (A). The seating for the drive shaft and the sprocket are in the rear part (B). -
Page 8: Installation
INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener. - Page 9 POSITION THE OPENER Disengage the trolley mechanism (see section “Operating the manual release”) and slide it back towards the powerhead. Secure the hanging push arm up into the rail assembly temporarily using tape or rope, to avoid a hazard. SECTIONAL DOOR You will need a 50 mm piece of timber or similar spacer to gauge the distance between door and rail.
- Page 10 HANG THE OPENER The opener must be securely fastened to a sound structural support above the opener. fig.1 1.Postion the opener as in the previous step. Check the rail is centred over the door. Ensure the rail brackets (fig.1) is on the Powerhead end of the rail in a position as close to the opener as possible (X).
-
Page 11: Operate The Manual Release
Make sure the garage door is fully closed. Pull the manual release ATTACH DOOR ARM TO TROLLEY cord to disengage the trolley. Slide the trolley to around 300 mm Fig. 1 Fig. 2 from the header bracket. 1.The straight door arm is already preassembled to the trolley. 2.Install the curved arm onto the door bracket using the Clevis pin (2)(item 6 in Hardware Provided - Section 5) and R-Clip (3)(item 7 in Hardware Provided - Section 5) supplied. -
Page 12: Adjustment
ADJUSTMENT SECTION Travel limits regulate the points at which the door will stop PROGRAM THE TRAVEL LIMITS AND FORCE SETTINGS Without a properly installed safety reversal when moving UP or DOWN. The travel limit buttons are located under the access cover on the rear panel (figure 1). system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing door. - Page 13 TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important. Garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door.
-
Page 14: Install The Protector System (Optional)
INSTALL THE PROTECTOR SYSTEM (OPTIONAL) NOTE: This accessory must be used for all installations To prevent entrapment, install The Protector where the closing force as measured on the bottom of the System™ no higher than 100 mm above the floor. door is over 400 N (40 kgf). -
Page 15: Timer To Close
TIMER TO CLOSE FEATURE (TTC) Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. figure 1 The Timer to Close feature requires The Protector System (IR Beams) to be installed. Indicator LED Operation: This feature allows the door to automatically close from a fully open position after a specified time. -
Page 16: Install Warning Labels
INSTALL WARNING LABELS chamberlaindiy.com.au chamberlaindiy.co.nz For Service Call RISK OF ENTRAPMENT Installation Date Repeat Safety Reverse Test monthly. Door 114A3361 must reverse on contact with a 40mm obstacle For Service Call placed on the floor. Make necessary adjustments. AUTOMATIC DRIVE: Keep away from the area of the door since it may operate unexpectedly. -
Page 17: Wireless Programming
WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES) Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door. -
Page 18: Using Your Opener
MAINTENANCE AND CARE OF YOUR OPENER Battery of the remote control: USING YOUR OPENER REPLACE BATTERIES IN REMOTES 1. Your opener can be activated by any of the following devices: • Opener control panel: Up and Down Buttons. The batteries in the remote have an extremely long life. •... -
Page 19: Accessories
ACCESSORIES Model E950C 2 Channel remote control Model E1702C Quick release lock Model E940C 1 Channel visor remote control Model E840C Wireless Keypad Model 774AML The Protector System E1702C E840C E950C E940C 774AML... -
Page 20: Troubleshooting
TROUBLE SHOOTING 1. Opener doesn't operate from either door control or 7. Door opens but won't close: remote: • Check The Protector System™ (if you have installed • Does the opener have electric power? Plug lamp into this accessory). If the light on the Beams are flashing, outlet. - Page 21 DIAGNOSTIC CHART Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM POSSIBLE RESOLUTION UP Arrow DOWN Arrow Flash(es) Flash(es) The garage door opener will not Safety sensors are not installed, connected or wires may be cut.
-
Page 22: Specifications
SPECIFICATIONS - PowerLift Plus - CS100EVO IInput Voltage......230-240 Vac, 50 Hz Max. Pull Force ......1000 N Power ........225 Watt Standby Power ......0.8 Watt (door fully closed) Normal Torque ......7 Nm Max door weight......130 kg Max lift under spring tension ..20 kg Max door area......Sectional doors 16 m Motor Type..........DC gearmotor permanent lubrication... -
Page 23: Warranty
Chamberlain warrants to the original purchaser of the: 6 water or moisture ingress that causes corrosion or electrical malfunction; Chamberlain PowerLift Plus CS100EVO Sectional Door Opener (Unit) 7 corrosion caused by sea air if located near a waterway, beach etc;... - Page 24 Warranty Registration Register your warranty at: chamberlaindiy.com.au/warranty chamberlaindiy.co.nz/warranty Trademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. 114D4627G © 2018, The Chamberlain Group Inc.