Page 1
Instruction Manual 7” Waterproof Quad View Monitor RVS-082574 Please read this manual before using monitor. The product may be different from how it is described in the manual depending on what software version you are using. Reverse With Confidence ™...
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty.
Page 5
INSTALLATION: • Electric shock or product or disconnected wire may cause a malfunction may occur if this fire. product is installed incorrectly. • While installing the Rear View System be careful with the wire • Use this product within positioning in order to avoid wire the voltage range specified.
Page 6
If you have questions about this product, contact: RVS Systems 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.888.881.2601 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly.
Wiring After connecting the monitor to the power harness, plug the camera into the CAM 3 input. Connect the RED 12V power wire to an ignition power source and the BLACK 12V ground wire to a chassis ground. The BROWN wire is the REVERSE trigger wire. Connect this wire to the vehi- cle’s backup light circuit to activate the rear view image whenever the vehicle shifts into reverse.
Page 9
Precautions For Use Of Monitor I. The monitor is made of glass and plastic. Do not subject it to a mechanical shock by dropping it from a high place, etc. II. Do not apply excessive force to the monitor surface or the adjoining areas since this may cause the color tone to vary.
Page 11
7” Waterproof Quad View Monitor with a TFT LCD digital color touch screen display. Monitor comes with a U-Bracket, swivel head mount, and a waterproof rating of IP69K. • 7” Quad View Display with multiple viewing options • Completely waterproof - IP69K •...
Monitor Dimensions Dimension 7” TV System NTSC/ PAL Resolution 800 x 3 (RGB) x 480 Brightness 400 cd/m² Contrast 500 :1 Viewing Angle U: 50°/ D: 60°, R/L: 70° Aspect Ratio 16:9 Operating Temperature -10 ~ +65ºC Storage Temperature -30 ~ +80ºC Power Consumption Max.
On-Screen Display (OSD) • SCALE: Toggle distance grid lines ON/OFF. When ON, distance grid lines will be displayed when backup camera (CAM 3) is triggered. • INPUT SCAN: Toggle camera input auto identification. When ON, monitor will display connected cameras and skip inputs not connected. •...
Trigger Setting • TURN IMAGE: Display options when side cameras (CAM 1, CAM 2) are trig- gered. When on SINGLE, the corresponding camera will display when either camera is triggered. When on SPLIT, a split image of side and rear view camera will be displayed when either side camera is triggered.
• REC-V OUT: Toggle which camera view will record when a DVR is attached (LEFT/RIGHT/FRONT/QUAD). • AUTOSCAN: When setting is ON, the monitor automatically switches be- tween connected camera inputs and quad view. • SCAN DELAY: Toggle AUTOSCAN delay (0-60 seconds). •...
Camera Dimensions • 18 infra-red illuminators (enables you to see in total darkness) • 1/4 Sharp® color CCD, 250k pixels, 2.1 mm wide lens with 130° angle • Shock resistant with a 20G Vibration and 100G impact rating • Built-in high gain microphone RVS Systems...
Page 27
Camera Specifications SENSOR 1/4” SHARP® COLOR CCD PICTURE ELEMENTS 250,000 PIXELS GAMMA CORRECTION R=0.45 TO 1.0 IMAGE SENSOR 600 TV LINES, PAL: 500 (H) X 582 (V) NTSC: 510 (H) X 492 (V) LENS 2.1MM VIEW ANGLE 130° WATERPROOF RATING IP69K SYNC SYSTEM INTERNAL SYNCHRONIZATION...
Troubleshooting Problem Possible Causes/Solutions Adaptor is connected incorrectly. Improper power supply. No picture/sound Unit is off. No picture Check cable connection. Audio cable improperly connected. Volume is off or set very No sound low. Dark picture Adjust brightness/contrast. Low environmental temperature. No color Adjust the color settings.
ONE YEAR WARRANTY RVS SYSTEMS, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. RVS SYSTEMS, INC. IS NOT RESPON- SIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS.
Page 30
DISCLAIMER RVS SYSTEMS AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAU- TIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
Page 31
If you have any questions about this product, contact: RVS SYSTEMS, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 888.881.2601 Better Cameras. Better Service. IT’S OUR GUARANTEE. Reverse With Confidence ™...