LG OLED55E6 Series Manual
Hide thumbs
Also See for OLED55E6 Series:
- Safety and reference (244 pages) ,
- Manual (41 pages) ,
- Safety and reference (41 pages)
Related Manuals for LG OLED55E6 Series
Summary of Contents for LG OLED55E6 Series
- Page 1 OLED TV OLED55E6* OLED65E6* CR2032 (M4 X L12) P/No: MFL69387472 (1606-REV01) www.lg.com Printed in Korea...
- Page 4 ANTENNA / CABLE IN HDMI IN HDMI IN/ARC USB IN AUDIO OUT/ H/P OUT...
- Page 5 AUDIO OUT/ H/P OUT Satellite IN OPTICAL DIGITAL AUDIO OUT : Depending on model / Selon le modèle / Dependendo do modelo /...
- Page 6 AV IN COMPONENT IN VIDEO L/MONO AUDIO R AUDIO VIDEO...
- Page 9 OLED55E6V-T 1237 56.7 18.5 17.1 OLED55E6T-T OLED55E6Y-T OLED65E6V-T 1461 56.7 24.8 22.8 OLED65E6T-T OLED65E6Y-T...
- Page 13 Safety and Reference Please read this manual carefully before operating your set and retain it for future reference. www.lg.com *MFL69361136* P/NO : MFL69361136 (1703-REV02) Printed in Korea...
-
Page 14: Safety Instructions
Safety instructions Please read these safety precautions carefully before using the product. WARNING Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on earth.) Otherwise possibility you may be electrocuted or injured. Do not place the TV and/or remote control in the following environments: Insert power cable plug completely into wall socket otherwise if not... - Page 15 Do not plug too many electrical devices into a single multiple electrical Do not insert any metal objects/conductors (like a metal chopstick/ outlet. Otherwise, this may result in fire due to over-heating. cutlery/screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall.
- Page 16 It may cause a fire or a burn by a spark. Only use an authorized AC adapter and power cord approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction or product deformation. Do not disassemble, repair or modify the product at your own discretion.
- Page 17 CAUTION When installing the antenna, consult with a qualified service technician. If not installed by a qualified technician, this may create a Install the product where no radio wave occurs. fire hazard or an electric shock hazard. There should be enough distance between an outside antenna and We recommend that you maintain a distance of at least 2 to 7 times power lines to keep the former from touching the latter even when the the diagonal screen size when watching TV.
- Page 18 Signal from Remote Control can be interrupted due to external/internal Take care not to touch the ventilation openings when watching the TV lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting for long periods as the ventilation openings may become hot. This does or darken viewing area.
- Page 19 Avoid touching the screen or holding your finger(s) against it for long When moving or unpacking the product, work in pairs because the periods of time. Doing so may produce some temporary or permanent product is heavy. Otherwise, this may result in injury. distortion/damage to screen.
-
Page 20: Viewing 3D Imaging (Only 3D Models)
In this case, stop watching the 3D video and take a rest. • Only use LG 3D glasses. Otherwise, you may not be able to view 3D Some horizontal lines may appear when the Clear Panel Noise feature is videos properly. -
Page 21: Separate Purchase
• If you do not use a certified HDMI cable, the screen may not display AG-F*** AN-TD700 or a connection error may occur. (Recommended HDMI Cable Types) Cinema 3D Glasses LG Twin TV Engine - High-Speed HDMI cable (3 m or less) ® AN-VC550... -
Page 22: Basic Functions
• When transporting a large TV, there should be at least 2 people. <B type> • When transporting the TV by hand, hold the TV as shown in the following illustration. • When transporting the TV, do not expose the TV to jolts or excessive vibration. -
Page 23: Mounting On A Table
LG recommends that wall mounting be performed by a qualified professional installer. We recommend the use of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with cables connected. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. -
Page 24: Separate Purchase(Wall Mounting Bracket)
NOTE • To remove the stand, hold the top and bottom of stand, then pull it out while also lowering it as shown below. (Only OLED55/65E6*) 10 cm Make sure to use screws and wall mount bracket that meet the VESA standard. -
Page 25: Ci Module Connection
CI module connection NOTE • The external device connection may differ from the model. (Depending on model) • Connect external devices to the TV regardless of the order of the View the encrypted (pay) services in digital TV mode. TV port. • ... -
Page 26: Battery Installation
Slim remote control Returns to the previous level. (Depending on model) Clears on-screen displays and returns to TV viewing. (HOME) Accesses the Home menu. The descriptions in this manual are based on the buttons on the remote (INPUT) Changes the input source. control. -
Page 27: Magic Remote Functions
Magic remote functions Adjusts the volume level. (Depending on model) Scrolls through the saved programmes. When the message “Magic remote battery is low. Change the battery.” is (MUTE) Mutes all sounds. displayed, replace the battery. * By pressing and holding the button, audio descriptions function will be enabled. -
Page 28: Registering Magic Remote
Registering magic remote LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to How to register the magic remote opensource@lge.com. -
Page 29: Troubleshooting
Troubleshooting Specifications Cannot control the TV with the remote control. Wireless module specification • Check the remote control sensor on the product and try again. • As band channels can vary per country, the user cannot change or • Check if there is any obstacle between the product and the remote adjust the operating frequency. - Page 30 CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm Operating 0 °C to 40 °C Temperature Operating Less than 80 % Humidity Environment condition Storage -20 °C to 60 °C Temperature Storage Less than 85 % Humidity 1 Only Satellite models.
- Page 31 Regulatory WARNING! Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as: • Using cabinets or stands recommended by the manufacturer of the television set. • ...
- Page 32 0800 545454 in South Africa quote this information to your dealer when 080 100 54 54 in Morocco requiring any service. 19960 in Egypt 021 36 54 54 in Algeria MODEL Other countries, Please contact our local dealer or log into SERIAL http://www.lg.com...
-
Page 33: External Control Device Setup
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com... -
Page 34: Key Codes
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button... - Page 35 (TV) (PC) • LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter RS-232C IN which is not made nor provided by LG. (CONTROL & SERVICE) (PC) (TV) • It can be purchased from computer stores that carry accessories for IT support professionals.
- Page 36 EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
-
Page 37: Communication Parameters
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA... -
Page 38: Transmission / Receiving Protocol
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. - Page 39 EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
- Page 40 EXTERNAL CONTROL DEVICE SETUP 08. Color/Colour (Command: k i) 13. Treble (Command: k r) ► To adjust the screen Color(Colour). ► To adjust treble. You can also adjust colour in the PICTURE menu. You can also adjust in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64...
- Page 41 EXTERNAL CONTROL DEVICE SETUP 18. Equalizer (Command : j v) * Analog Antenna/Cable ► Adjust EQ of the set. [Data 00][Data 01] Channel Data Transmission [j][v][ ][Set ID][ ][Data][Cr] Data 00 : High byte channel data Data 01 : Low byte channel data - 00 00 ~ 00 C7 (Decimal : 0 ~ 199) Data 02 : Input Source (Analog) - 00 : Antenna TV (ATV)
- Page 42 EXTERNAL CONTROL DEVICE SETUP * Analog Antenna/Cable 2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 : Physical Channel Number Data 00 = Don’t know Physical = 00 - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) Data 01 &...
- Page 43 11 11 EXTERNAL CONTROL DEVICE SETUP 2. Tune to the BS (ISDB-BS) channel 30. 24. Input select (Command: x b) Set ID = All = 00 (Main Picture Input) Data 00 = Don’t know Physical = 00 ► To select input source for main picture. Data 01 &...
- Page 44 EXTERNAL CONTROL DEVICE SETUP * [Data 02], [Data 03] functions depend on model 3) When [Data 00] is 06, 07 and signal. 00 : Off 01 : On * If [Data 00] is 00 (3D On), [Data 03] has no meaning.