Premium 12-input 2/2-bus mixer with xenyx mic preamps & compressors, british eqs, 24-bit multi-fx processor and usb/audio interface, premium 12-input 2/2-bus mixer with xenyx mic preamps & compressors, british eqs and usb/audio interface (21 pages)
Legendary analog dual vcf module for eurorack (21 pages)
Summary of Contents for Behringer Xenyx 1832FX
Page 1
All manuals and user guides at all-guides.com Users Manual Version 1.0 January 2006...
Page 2
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
2.1 Mono channels ..............5 This not only led me to 2.1.1 Microphone and line inputs ........5 establish BEHRINGER, 2.1.2 Equalizer ..............6 but also enabled me to 2.1.3 Monitor and effects busses (Aux sends) .... 6 share my enthusiasm 2.1.4 Routing switch, PAN, SOLO and channel fader ...
1. INTRODUCTION an optimal solution for singers who need accompanying music for their rehearsals. Congratulations! In purchasing the BEHRINGER XENYX you have acquired a mixer whose small size belies its incredible versatility and audio performance. The USB interface supplied with the unit is a perfect match for...
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX Should your BEHRINGER product malfunction, our goal is to have it repaired as quickly as possible. To arrange for warranty All other mixing console functions fall under this vital category. service, please contact the retailer from whom the equipment Creating a mix means primarily adjusting the volume levels was purchased.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX the MID control to set the amount of boost or cut, and the FREQ Insert points enable the processing of a signal with dynamic control to determine the central frequency. processors or equalizers. They are sourced pre-fader, pre-EQ and pre-aux send.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX 2.2 Stereo channels Fig. 2.4: The panorama and routing controls and the channel fader The PAN control determines the position of the channel signal Fig. 2.5: The various stereo channel inputs within the stereo image.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX Fig. 2.6: Balance control and mute switch The BAL(ANCE) control has a similar function to the PAN control in the mono channels. The balance control determines the levels of the left and right input signals relative to each other before both signals are routed to the left/right main mix bus (or odd/even subgroup).
You can easily use the headphones distribution amplifier BEHRINGER POWERPLAY PRO HA4700/HA8000 to provide four (HA8000: eight) stereo headphone mixes for your studio. The following table shows which jacks on the console can be used for this purpose.
The output signal of a second XENYX or the the aux 1 output and return the effect signal via AUX RETURN 2 BEHRINGER ULTRALINK PRO MX882 can also be connected to the monitor signal. here. If you connect the output of a hi-fi amplifier (with a source selection switch) to the CD/TAPE INPUT, you can easily listen to additional sources (e.g.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX via the high-precision MAIN MIX fader. When recording to digital recorders, the recorders meter should not go into overload. This is because, unlike analog recordings, it takes only slightly excessive levels to create unpleasant digital distortion.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX The switch turns on the FBQ Feedback Detection You can connect headphones to this 1/4" stereo jack (2442FX: System. It uses the LEDs in the frequency band 2 phones jacks). The signal routed to the PHONES connection is faders to indicate the critical frequencies.
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX sufficiently high level. Take care to ensure that the clip LED only machine so that you have 2 x 4 tracks available (e.g. channel 1 to lights up at peak levels. If it is lit constantly, you are overloading track 1 and 2, etc.).
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX which meets the required safety standards. Blown fuses must only be replaced by fuses of the same type and rating. The mains connection is made via a cable with IEC mains connector. An appropriate mains cable is supplied with the equipment.
Page 15
All manuals and user guides at all-guides.com XENYX 1622FX/1832FX/2222FX/2442FX Fig. 6.4: 1/4" stereo plug Fig. 6.5: Insert send/return stereo plug Fig. 6.6: Stereo plug for headphones connection 6. INSTALLATION...
Page 16
Reference = +6 dBu. Impedance approx. 20 kW bal. / 10 kW unbal. BEHRINGER is constantly striving to manintain the highest professional standards. As a Max. input level +22 dBu result of these efforts, modifications may be made from time to time to existing products without prior notice.
Page 17
BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER is a registered trademark.