Sealey IWMH2003RC Instructions page 2

Infrared quartz heater wall mounting with remote control

page of 2

/ 2
Bookmarks

INTRODUCTION & SPECIFICATION

A totally dry heat, no condensation, no gas, no fumes and no smell. Reaches maximum heat output within seconds of being turned on. Highly polished

aluminium reflector for maximum heat efficiency. Adjusts horizontally through 25° while mounted. Three settings, controlled by push on/off switch or

remote control, allowing unit to be on full, half or low power. Ideal for industrial or domestic applications. Suitable for indoor and outdoor use, if weather

protected.

Power:

Input supply:

Dimensions (W x H x D)

MOUNTING INSTALLATION

3.1

WALL MOUNTING (fig.1).

(IMPORTANT! The following points should be noted): The heater

should always have a minimum clearance of 450mm from a ceiling

and at least 90cm from any object. Ensure that mounting surface is

capable of supporting the weight of the heater.

3.2

Remove the metal bracket from the heater by removing the

single screw from the underside of the bracket and sliding the

bracket down.

3.3

Use the bracket as a template, fix the metal bracket to the wall

by means of the four holes and appropriate fixings.

3.4

Slide the heater back onto the bracket and secure using the

single screw.

3.5

Adjust the angle of heater to direct heat where required.

OPERATION

Note: The infrared lamp is fragile and therefore it is important that it is not subjected to any unnecessary shocks or vibration and is not moved

when it is on or still warm. Only move once completely cooled down.

WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before using the heater.



4.1

Ensure the heater is at least 90cm from any object. The heater can be tilted from 0° to 25°, set it to the required angle before switching

the heater on.

4.2

Plug in the heater and switch it on using either the control on the base of the heater or by using the remote.

4.3

The heater will start on the low setting, each press of the on/power button will cycle the heater onto the medium setting, high setting and

then back to the low setting.

4.4

When the heater is no longer required, switch off, using the off button on the unit or the off button on the remote and unplug the unit.

4.5

Make sure the heater plug is disconnected from the mains supply before any cleaning is attempted. Also allow the heater to cool

completely. DO NOT use water or other liquids, or harsh abrasive cleaners to clean the heater. DO NOT touch the glass elements with

fingers as this may damage the tube(s).

4.6

Clean the exterior with a soft damp cloth with some mild detergent.

4.7

To replace any of the lamps, contact your authorised Sealey dealer.

4.8

To change the remote batteries, press down and push back the

battery cover (fig.2), remove old batteries and replace with two

new AAA batteries.

WARNING! DO NOT mix old and new batteries and dispose of



old batteries in accordance with local authority regulations.

Declaration of Conformity

standards and directives.

INFRARED qUARTz hEATER

Model: IWMh2003RC

2006/95/EC low Voltage Directive

2004/108/EC EMC Directive

93/68/EEC Marking Directive

2002/95/EC RoHS Directive

2002/96/EC WEEE Directive

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.

2000W

230V 50Hz 13A

485 x 250 x 170mm

We, the sole importer into the UK, declare that the product listed here is in conformity with the following

The construction file for this product is held by the Manufacturer and may be inspected, by

a national authority, upon request to Jack Sealey ltd.

Signed by Mark Sweetman

For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.

Sole UK Distributor