Summary of Contents for Think Appliances VEF90EG
- Page 1 INSTALLATION INSTRUCTIONS USER INSTRUCTIONS COOKER MODEL VEF90EG 90X60 cm Important information Introducing your new cooker We thank you and congratulate you on your choice. These instructions cover four cooker models:...
- Page 2 We also carry a complete range of spare parts for all Think products. For all your spare parts enquiries please contact our team at Pronto Parts on: 1300 306 973 Again, thank you for choosing an appliance brought to you by Think Appliances and we look forward to being of service to you. Kind regards...
- Page 3 These carefully designed products, manufactured with the highest quality materials, have been corefully tested to satisfy all your cooking demands. We therefore request that you read and follow these easy instructions which will allow you to obtain excellent results right from the start. AlI cookers feature a gas hotplate containing 5 cooktop burners, including one centrai wok burner, and the multi-function ovens.
-
Page 4: Installation Instructions
Do not use the cooker if it is damaged in any way. Installation and connection of the cooker should be performed according to the instructions and connection diagram provided, and should be entrusted to a licensed specialist. In the event of a damage that occurs as a result of improper connection, the warranty will be void. -
Page 5: Installation
2. The appliance requires connection to a 240 V,50 Hz electric supply. The power point must be installed by an authorized person. 3. Before commencing any work, make sure that the power point switches ore turned off and the three in plug is removed 4. - Page 6 Height over hob: 910 mm Height over upstand: 980 mm Width: 895mm & handle Depth: (incl. oven door knobs): 660mm Depth: (flush with oven door): 610mm Gas and electric connection connection Electrical The electric lead and plug are for connection onto a 15 Amp socket. A 15 Amp socket is to be within 1 m of the appliance.The lead is situated at the left hand side of the cooker.
-
Page 7: Gas Connection
Gas connection The cooker must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid requlations. We recommend that the isolation valve be fitted prior to the cooker to enable isolation of the cooker from the gas supply. -
Page 8: Test The Operation Of The Cooker Before Leaving
Test the operation of the cooker before leaving Note: These burners have no aeration adjustment Check correct operation of the ignitions system and operation of burners individually and in combination. Burner flames should be clear blue, with no yellow tipping. If the burners show any abnormality check that the burners are correctly located. - Page 9 If the legs are not used and the cooker is mounted onto a plinth, fit transit legs to allow for clearance. Once legs are adjusted to a nominai cooker height of 91 Omm, fit the antitilt restraint bracket. 1. Fit flat strap to rear of cooker at the centre point on lower edge using supplied screw 2.
-
Page 10: Upstand Installation
5. Locate the cooker into correct and final position. Then from the underside front, secure into position with self tapping screw provided. WARNING - IN ORDER TO PREVENT ACCIDENTAL TIPPING OF THE APPLIANCE, FOR EXAMPLE BY A CHILD CLIMBING ONTO THE OVEN DOOR, THE STABILISING MEANS MUST BE INSTALLED. REFER TO THE INSTRUCTIONS FOR INSTALLATION Upstand installation All stainless steel hob models are fitted with an upstand. -
Page 11: Cooktop Burner Operation
4. Remove the remaining protective film from the upstand and secure end caps using M4 CSK screws, one each end. Hob & control panel lay-out DAF90EG 1. Minute minder 2. Thermostat control knob 3. Function selector control knob 4. Thermostat indicator light 5. - Page 12 Ignition 1. To operate the individual cooktop burners depress the appropriate control knob and turn anti-clockwise to the spark symbol. Push to activate the electronic ignition. 2. Once flame is established turn the knob to the desired setting. 3. If the flame goes out repeat the procedure. NOTE: if the burner does not ignite within 5 seconds, wait 5 minutes before reigniting.
- Page 13 Electronic clock (if applicable) To program the cooker press the desired function button and adjust the required time using the + and - buttons Setting time of day When first switching on power to the appliance, or after a power failure, the timer display flashes 0.00.
-
Page 14: Manual Operation
Manual operation 1. T urn the function selector control knob to the required mode. 2. Then turn thermostat control knob to the desired temperature. NOTE: only the symbol should be illuminated Manual operation with timer 1. Turn the function selector control knob to the required mode. 2. -
Page 15: Oven /Grill Operation
At the conclusion of the cooking time the signal will sound and the 'A' symbol will flash. will turn off and the oven will also turn off. To stop the signal press the button. Automatic operation with end cooking In this mode the oven is programmed to start and stop at a predetermined time. symbol and using the + and - buttons adjust the time you wish the 1. - Page 16 Foods being grilled must be monitored at ali times, especilally high fat content foods such as sausages, chops, ek. First time use Thoroughly clean the appliance and accessories with warm soapy water before using them for the first time. Operate the oven for about 30 minutes at 200°C on fan forced or fan assisted in order to eliminate any odours from all oven elements.
-
Page 17: Grill Operation
The orange thermostat indicator light illuminates when the oven is first turned on, and extinguishes when the required temperature is reached. The indicator light will cycle ON and OFF as the element cycles ON and OFF to maintain the oven temperature Grill operation Note: due to the operation of the cooling fan, all methods of grilling in this oven require the oven door to be closed during grill operation. -
Page 18: Oven Cooking Tips
simultaneously on different shelves and food can be placed on any shelf position. Meat cooked in fan forced mode will brown on all sides, eliminating the need for a separate rotisserie function. It is particularly suitable for roasting cuts of meat weighing more than 150g. - Page 19 Food cooking too quickly Oven temperature set too high Check oven chart, Iower temperature Pan used larger than recipe required Allow less time or use smaller pas Thermostat too high faulty Phone service number for service or advice Food taking too long to cook Avoid opening door and minimise Opening oven door too frequently time open...
- Page 20 discoloured over time. THIS IS NORMAL. Clean the hob with a product suitable for cleaning stainless steel Never use abrasive products, sharp objects, steel scouring pads, knives, etc., to remove stubborn food remains from the hob surface, trivets, burners and oven interior Do not allow acidic products such as vi negar, lemon juice etc., to come into contact with the hob Cleaning oven interior...
-
Page 21: Service Information
Use a window cleaner to clean the exterior glass panel. Replacing light bulb the oven Type: E 14, 25W, heat resistant to 300°C. You may obtain this bulb from our service department 1. Disconnect the appliance from the main electricity supply. 2. - Page 22 2. Using a 7mm socket spanner unscrew and clean or replace the cooktop burner's injector. 3. Replace burner head, cap and pan support. Ensure that the burner head and cap are in the correct position. Access to the under hob area Pull cooker forwards to gain access to the rear of the cooker 1.
- Page 23 Wiring diagrams model VEF90EG...
-
Page 24: Data Plates
A copy of those diagrams is situated on the back panel of the cooker. Data plates The data plates reproduced below cover all three cookers. You will find your particular model number on the data plate attached to the inside of the oven door, centre bottom. Always quote your model number when requesting a service calI.
Need help?
Do you have a question about the VEF90EG and is the answer not in the manual?
Questions and answers