Enerwave WF15RM Installation Instructions

INSTALLATION INSTRUCTIONS
Model: WF15RM
Wi-Fi Receptacle
with Smart Meter

FEATURES

• Control your lights or small appliances with your smart devices without
the need of any hub
• Easy to configure, easy to use free smart App by Enerwave
• Save energy by automating the ON/OFF times or using the timer
• Works with Amazon Alexa, Google Assistant through the Tuya App
• Features a top "Always On" outlet and a bottom "Smart" energy
metering outlet
• Reduce energy consumption and enjoy wireless home automation with
Smart Meter monitoring
• Interchangeable face covers included: White, Light Almond and Black

SPECIFICATIONS

Voltage...........................................................................................120VAC, 60Hz
Incandescent...............................................................................................1000W
Electronic Ballast...............................................................................................5A
Standard Ballast........................................................................................1200VA
Resistive...........................................................................................1800W (15A)
LED...............................................................................................................150W
Motor............................................................................................................1/2HP
Protocol.......................................................................................IEEE 802.1b/g/n
Wireless Type............................................................................................2.4GHz
System Requirements................................Android 4.1 or higher/ iOS 8 or higher
Operating Temperature..........................................................32°-104°F (0°-40°C)

REQUIREMENTS

• Secure 2.4GHz Wi-Fi network connection
• Smart Device such as a Smart Phone or Tablet with an
operating system of Android version 4.1 or higher or iOS 8 or
higher
• Installation of the ENERWAVE Smart App on the Smart Device
1

WARNING

Turn the POWER OFF at the circuit breaker before installing the
smart receptacle.
Read and understand these instructions before installing. This device is intended
for installation in accordance with the National Electric Code and local
regulations. It is recommended that a qualified electrician performs this
installation. Make sure to turn off the circuit breaker or fuse(s) and make sure
power is off before wiring the device.
Use copper wire only.
This smart receptacle CANNOT be used if the outlet you are replacing has
the top and bottom outlets controlled by separate circuit breakers.

WIRING DIRECTIONS

DO NOT REVERSE ANY WIRES. DOING SO WILL VOID YOUR WARRANTY AND
THE SMART RECEPTACLE WILL SHORT CIRCUIT.
Step 1. Identify all your wires. Label the wires or draw a diagram of existing wires.
Step 2. Insert wires into the terminal holes on the back, then tighten the terminal screws.
• Connect the BLACK wire to the HOT terminal (brass screw).
• Connect the WHITE wire to the NEUTRAL terminal (silver screw).
• Connect the GREEN or BARE wire to the GROUND terminal (green screw).
Neutral
White
Ground
Meter
Green
2

CHANGING THE FACE COVER

To replace the face cover, use a flat screwdriver and insert
the tip at the gap shown in the diagram above and pry cover
off. To re-install, simply align the cover and snap back on.

FCC COMPLIANCE STATEMENT

FCC Grant of Equipment Authorizations of this device and transmitters installed in this
device can be found at FCC website by entering the FCC ID number on the device.
Caution: Changes or modifications not expressly approved by the part responsible for
compliance could void the user's right to operate the equipment. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
Hot interference received, including interference that may cause undesired operation of the
device.
Black
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Always-on Receptacle
LED Indicator
Program Button
Energy Metering Wi-Fi Outlet
© 2019 Enerwave Home Automation
3
WWW.ENERWAVEAUTOMATION.COM
0206190142