Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for S.R.Smith poolLUX Plus pLX-PL60
- Page 1 poolLUX Plus ® pLX-PL60 & pLX-PL100 5005508 ETL LISTED Conforms to UL STD 379; Certified to CSA STD C22.2 #218.1 Installation Instructions Read all instructions before attempting to perform installation work Type 3R Rainproof Enclosure FOR USE WITH POOL AND SPA PRODUCTS 79-15264-00 REV6/18...
-
Page 3: Table Of Contents
Contents IMPORTANT SAFETY INFORMATION ....... . 4 RF Exposure Statement ..........5 IC Statement. -
Page 4: Important Safety Information
I M P O R T A N T S A F E T Y I N F O R M A T I O N CAUTION: POWER AND SIGNAL OUTPUT CONDUITS MUST BE NON-METALLIC ATTENTION: CONDUITS POUR PUISSANCE DE SORTIE ET SORTIE SIGNAL DOIT ETRE NON METALLIQUE ELECTRICAL SHOCK HAZARD –... -
Page 5: Rf Exposure Statement
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by S.R.Smith, LLC will void the user’s authority to operate the equipment. -
Page 6: Electrical Ratings
E l e c t r i c a l R a t i n g s Do not exceed the maximum electrical output rating of each unit listed below. Model Input Output pLX-PL60 120 VAC, 60 Hz, 0.6A max 12-13 VAC, 60 Watt max pLX-PL100 120 VAC, 60 Hz, 1.0A max... -
Page 7: Installation Instructions
I N S T A L L A T I O N I N S T R U C T I O N S WARNING • TURN OFF INCOMING POWER BEFORE SERVICING EQUIPMENT. • ALL INSTALLATION AND MAINTENANCE WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN. - Page 8 By hand, open the enclosure by pulling the front cover off evenly by the top and bottom tabs. Do not angle or ‘hinge’ the cover when removing or damage may occur. If you cannot open the enclosure by hand, use a flat blade screwdriver to twist open the finger tabs of the cover at the top and bottom of the unit.
-
Page 9: Input / Supply Line Voltage
I n p u t / S u p p l y L i n e V o l t a g e Remove the metal input voltage isolation barrier by unscrewing the mounting screw. Once the securing screw is removed, the isolation cover will pull straight out to allow easier access to the conduit knockout locations. -
Page 10: Output Wiring For Lights And Light Sources
Attach an approved ‘rain-tight’ or ‘wet location’ hub to the conduit. After the hub is attached to the conduit, attach the hub to the enclosure. Connect the GFCI protected, 15A max, supply voltage line to the right side of the terminal block. - Page 11 CAUTION – IF USING FEEDER OR SUPPLY LINES TO A JUNCTION BOX, BE SURE TO USE THE APPROPRIATE WIRE GAUGE FOR THE LOAD AND DISTANCES INVOLVED. Using a hole saw, open the knockout for the size of the conduit (¾" or 1") being installed. Bring output conduits to the open conduit locations.
-
Page 12: Operating Instructions
O P E R A T I N G I N S T R U C T I O N S M a n u a l R o c k e r S w i t c h O p e r a t i o n The poolLUX Plus comes with one rocker switch ®... -
Page 13: Wireless Remote Operation
W i r e l e s s R e m o t e O p e r a t i o n The new poolLUX Plus wireless remote system is shipped ready to use and requires no additional ® programming. -
Page 14: Wiring Diagram
W I R I N G D I A G R A M REMOTE NOTES: UNLESS OTHERWISE SPECIFIED 1. WIRE COLOR LEGEND: R = RED W = WHITE BK = BLACK B = BLUE Y = YELLOW G = GROUND 2. -
Page 15: Replacement Parts
R E P L A C E M E N T P A R T S Replacement parts for the poolLUX Plus (pLX-PL60 or pLX-PL100): ® Transformer (pLX-PL60) 44-15039-00 Transformer (pLX-PL100) 44-15040-00 3-Way Switch 38-15002-01 Isolation Barrier 02-15342-00 Isolation Barrier mounting screw, 8-32 10-15078-05 Fuse Holder 36-15016-00... - Page 16 Questions? 1-800-824-4387 Contact One of Our Dedicated Lighting Specialists. x4012 or x2282 S.R.Smith, LLC P.O. Box 400 | Canby, OR 97013 P 503.266.2231 TF 800.824.4387 srsmith.com © 2018 S.R.Smith. All rights reserved. 79-15264-00 REV6/18...
Need help?
Do you have a question about the poolLUX Plus pLX-PL60 and is the answer not in the manual?
Questions and answers