Page 1
MKB02 Mini Mobile PTZ Keyboard Controller User Manual http://iotsmartsolutions.net...
Page 2
Safety Notes Thank you for choosing our mini keyboard controller! When you open the box: 1. Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if any parts are either missing or damaged. 2. Make sure if the contents are all included as per the packing list. 3.
Table of Contents About The Product ....................1 Introduction .......................1 Features ........................1 Technical Data ......................1 Parts And View ......................2 Connections ......................4 operation ........................ 6 Menu Operation ......................6 Camera Setting ......................7 Time Setting ......................9 Volume Setting ......................9 Backlight Setting ....................10 Sleep Setting ......................10 Pin Setting .......................11 Joystick Calib ......................13 Key Custom ......................14...
Page 4
Safety Notice---Important!!! The following important notes must be followed carefully to run the controller and respective accessories in total safety. Power shall be cut immediately when the controller is not working correctly; Use DC12V power supply. Wrong power supply may damage the controller; ...
About The Product Introduction The mini keyboard controller is a full-function system keyboard. With features of ergonomic design, multi-function, high reliability and easy operation, it is a perfect controller for rugged PTZ cameras, video conference cameras, surveillance cameras and so on. Features ...
About The Product Parts and view Press SETUP key to enter menu and program ① OLED screen The OLED screen displays status of current the keyboard operation. ⑥ CRUISE (Auto Cruise) ② CALL (Call preset) Press CRUISE key to do auto cruise. Input preset number, then press CALL key to ⑦...
Page 7
About The Product Left: Return to previous menu or exit (expect ⑪ 0~9 (Numbers) Those are keys used to input numbers. some not returnable menus); Combine with SHIFT key to activate various Up: Move to last option; functions shown on number keys. For Down: Move to next option.
About The Product Connections There are two options of cables. Please see the instruction label at bottom of the device. Option1: Power + Aux output + RS-485...
Page 9
About The Product Option2: Power + RS-232 + RS-485...
Operation Menu operation After powered on, “USER PIN” will show on the controller’s screen. The initial pin is “111111”. Enter “USER PIN” - - - - USER PIN: See “PIN SETTING” to set pin. Pin Error:When“USER PIN:ERROR” shows on screen, it indicates wrong pin was input. Enter correct pin to get to next step Pin Correct:Screen shows“...
Operation OSD Menu List: Camera Setting Set camera ID (Range from 0~255), corresponding protocol, baud rates and camera address of the target cameras. Then every camera can be controlled easily by choosing their relative camera ID. ❶ Move up / down the joystick, choose “CAMERA SETTING”. ...
Page 12
Operation ❸ Protocol Setting. Move up/down the joystick, choose protocol, right move the joystick or press ENT to confirm. Set protocol. This protocol must be the same - - - - PROTOCOL:PELCO D as the camera’s protocol. Available Options: PELCO D/PELCO P /VISCA ❹...
Operation Time Setting Set time in 24 hour format. ❶ Move the joystick up/ down, choose ”TIME SETTING”. - - - - Time Setting TIME SETTING ❷ Right move the joystick or press ENT to get into time setting menu, “H” hour becomes editable, input digits from keypad or move joystick up / down to set the “H”...
Operation - - - - Volume setting VOLUME SETTING ❷ Right move the joystick or press ENT to get into “ VOLUME SETTING” ; after setting right move the joystick or press ENT to confirm. Available Value: - - - - OFF (switch off sound) VOLUME SETTING:OFF 1~6 (6 levels from low to high)
Operation - - - - Sleep setting SLEEP SETTING ❷ Right move the joystick or press ENT to enter “ SLEEP SETTING” . Move the joystick up/ down to select sleep time. Right move the joystick or press ENT to confirm. Available Value: - - - - SLEEP TIME:30S...
Page 16
Operation Input “OLD PIN”: - - - - OLD PIN: Initial USER PIN:111111 Initial ADMIN PIN:111111 ❹ “NEW PIN” - - - - NEW PIN: Input “NEW PIN” (Digits key) ❺ “CONFIRM”: after new pin is input, input it again to confirm. If the two pins don’t match, it displays “PIN NOT MATCH”, menu goes back to “NEW PIN”.
Operation Joystick Calib After long-time use, the joystick may require calibration. ❶ Move the joystick up/ down, select “JOYSTICK CALIB”. - - - - Joystick calibration JOYSTICK CALIB ❷ Right move the joystick or press ENT to confirm, enter the “JOYSTICK CALIB” menu. “PAN LEFT”...
Operation Zoom wide. Twist the joystick anticlockwise until limit - - - - ZOOM WIDE position + press ENT. ❻ “FREE STATE” setting menu, no need any operation, simply press ENT to confirm. - - - - No need any operation, press ENT . FREE STATE ❼...
Page 19
Operation - - - - PATT PRESET: 60 PATT PRESET:60 - - - - Changed to 60. (Numeric CHANGED TO:60 Keys) ❹ Example of keys with special function printed: If preset 35 is requested to activate WIPER, press 7(WIPER) and SHIFT in the same time. If press 7(WIPER)...
Operation Speed Setting Set control speed of the joystick. ❶ Turn the joystick up/down, choose"SPEED SETTING". - - - - Speed Setting. SPEED SETTING ❷ Right move the joystick or press ENT to enter "SPEED SETTING" menu. Move the joystick up/ down to switch among speed levels, and right move the joystick or press ENT to confirm HIGH;...