Advertisement
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
12. Do not let the cord hang over the edge of a table,
should always be taken including the following:
counter or come in contact with hot surfaces or leave
1. Read all instructions before using this appliance.
exposed to high traffic areas.
2. Use fan only for purposes described in the instruction
13. Do not use outdoors.
manual.
14. To disconnect, grip plug and pull from wall outlet.
3. To protect against electrical shock do not immerse unit,
Never yank on cord.
plug or cord in water or spray with liquids and plug
15. Always use on a dry, level surface.
the appliance directly into a 120V AC electrical outlet.
16. Do not operate fan until fully assembled with all parts
4. Close supervision is necessary when any appliance is
properly in place.
used by or near children.
17. This product is intended for household use ONLY and
5. Unplug from outlet when not in use, when moving
not for commercial or industrial applications.
fan from one location to another, before putting on or
18. WARNING: To reduce the risk of electrical shock and
taking off parts and before cleaning.
injury to persons, do not use in window.
6. Avoid contact with moving parts.
19. WARNING: To reduce the risk of fire or electric
7. Do not operate in the presence of explosive and/or
shock, do not use this fan with any solid-state speed
flammable fumes.
control device.
8. To avoid fire hazard, NEVER place the cord under rugs
20. This product employs overload protection (fuse).
or any parts near an open flame, cooking or other
A blown fuse indicates an overload or short-circuit
heating appliance.
situation. If the fuse blows, unplug the product from
9. Do not operate any appliance with a damaged cord
the outlet. Replace the fuse as per the user servicing
or plug after the appliance malfunctions, or has been
instructions (follow product marking for proper fuse
dropped/damaged in any manner. Discard fan or
rating) and check the product. If the replacement fuse
contact customer service.
blows, a short circuit may be present and the product
10. Do not run cord under carpeting. Do not cover cord
should be discarded or contact customer service.
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
PLEASE READ AND SAVE
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
THESE IMPORTANT SAFETY
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
A N D O P E R A T I N G I N S T R U C T I O N S
ASSEMBLY
Your Table Fan comes completely assembled and is ready
for use.
Figure 1
A
A. Fan Head
B. Motor Housing
(not visible)
C. Fan Base
D. Tilt Ajustment
Knob
E. Speed Selector
Switch (not visible)
INSTRUCTIONS
A S S E M B LY, P A R T S
OPERATING INSTRUCTIONS
1. Set fan on a dry, level, and stable surface.
2. Make sure the Selector Switch is in the OFF (O)
position. Plug cord into any standard 120 volt AC
outlet.
3. Press the selector switch to choose the desired setting:
O (OFF)
B
I (LO)
E
II (HI)
D
TILT ADJUSTMENT
VERTICAL ANGLE ADJUSTMENT
1. To adjust the angle, move the fan head to the desired
position.
C
2. Firmly tighten the Tilt Adjustment Knob (D) to keep
the fan head in place.
C L E A N I N G / M A I N T E N A N C E
USER SERVICING INSTRUCTIONS
CAUTION: Risk of fire. Do not replace the attachment
plug. It contains a safety device (fuse) that should not
Follow these instructions to safely and correctly care for
be removed. Discard product if the attachment plug is
your fan.
damaged.
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows,
FAN CLEANING
please visit our website at www.getholmesfans.com for
information on how to order a new fuse.
• Always unplug the fan before cleaning.
• Wipe the fan grill, housing and base with a soft,
REPLACING THE FUSE
damp cloth.
1. Unplug your fan.
• Do not allow water to drip on or into the fan
Grasp plug and remove from the receptacle or other
housing.
outlet device.
• Use only a soft cloth moistened with a mild soap
NOTE: Do not unplug by pulling on cord.
solution.
2. Open fuse cover, located on the top of the plug, by
• Do not use harsh chemicals such as gasoline,
using your thumb or a flathead screwdriver to slide
thinner or benzene as a cleaner.
the cover towards the prongs.
• Do not attempt to remove the fan blade.
NOTE: Ensure the fuse cover is completely open
• Use CAUTION around the motor housing area.
before attempting to remove fuse.
Do not allow the motor or other electrical
3. Remove fuse carefully by using a small screwdriver to
components to be exposed to water.
pry it from the compartment at the metal ends of the
fuse. (See Figure 2)
FAN STORAGE
Figure 2
4. Place plug on a solid,
Fuse
Fuse cover
• Store the fan in a clean, dry location between seasons
flat surface. Insert new 5
or when not in use for an extended period.
Amp, 125 Volt fuse into
• Keep the fan head protected from dirt and dust during
fuse compartment. Use
Metal ends
storage.
a small screwdriver to
secure the metal ends of
the fuse into the compartment.
If you have any questions regarding your product
CAUTION: Risk of fire. Replace fuse only with 5
or would like to learn more about other Holmes
Amp, 125 Volt fuse.
products, please visit our website at
www.getholmesfans.com or call customer service:
5. Slide fuse cover closed completely.
1-866-769-3166 (8:30 am - 5:00 pm E.S.T.) or send
NOTE: If fuse cover is difficult to close, make sure
an email to info@getholmesfans.com. For inquiries
the fuse is completely secured in place by pressing on
regarding recycling and proper disposal of this
metal ends of the fuse.
product, please contact your local waste
management facility.
®
Advertisement
