Summary of Contents for Big Bee Gear Drive 6 Tines
- Page 1 Gear Drive 6 Tines Rotary Tiller (7 Feet) Operator Manual Part Catalogue † † † Service Manual...
- Page 2 If your manual is lost or destroyed, “BIG BEE” will be glad to provide you a new copy. Visit to nearest dealership & get a copy. Most of our manuals can also be downloaded from our website at www.darrellharp.com.
-
Page 3: Customer Information
4. Return the equipment or parts to the authorized “BIG BEE” dealer, from where it Sometime in the future your Rotary Tiller may need new parts to replace which are was purchased, for service or replacement of defective parts that are covered by warranty. - Page 4 INDEX INTRODUCTION 1.1. Tiller Identification 1.2. Intended Use 1.3. Main Parts Description SAFETY 2.1. General Safety Instructions 2.2. Equipment Safety Instructions 2.3. Operating Safety Instructions 2.4. Transporting Safety Instructions 2.5. Maintenance Safety Instructions 2.6. Storage Safety Instructions 2.7. Safety Labels ASSEMBLY AND SET-UP 3.1.
- Page 5 INTRODUCTION SAFETY Careful operation is your best insurance against an accident. All operators, no matter 1.1. Tiller Identification how much experience they may have, should carefully read this manual and other related manuals before operating the power machine and this implement. It is the Each tiller has a plate for unique identification.
- Page 6 • Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified by BIG BEE. When ordering new components make • Sudden braking can cause a towed trailer to swerve and upset. Reduce speed if towed sure the correct safety labels are included in the request.
-
Page 7: Assembly And Setup
3.2. Connecting to The Tractor Never stand between tractor and rotary tiller while backing up tractor to the hitch. • Place tiller and tractor on level ground. • Back tractor into position by lining up lift arms and Hitch bracket of the tiller linkage pins. Attach lift arms to linkage pins and secure with lynch pins. - Page 8 The PTO shaft maximum allowable length must, when fully extended, have a minimum 4.3 SKIDS ADJUSTMENT overlap of the profile tubes by not less than 1/3 the free length with both inner and outer profile tubes being of equal length. The working depth of the tiller is determined by the position of the side skids.
-
Page 9: Maintenance
TRANSPORTING Every 200 Work Hours • Change the oil in the gearbox or in the reduction unit and transmission casing by completely draining of the old oil through the drain plug, under the reduction unit and To set the tiller for transportation, perform the following steps: through the transmission drain plug. - Page 10 Fully check screws or bolts, particularly those fixing the hoe blades. Thoroughly lubricate the implement and lastly protect it with a plastic sheet. Store it in a dry place. Careful compliance with these instructions will be all to the advantage of the user who will be sure to use an implement in perfect conditions when work begins again.
-
Page 11: Torque Values Table
9. TORQUE VALUES TABLE Solution –Open the side gear cover and replace the part which is broken. First remove the lock & loose the check nut. Torque Values Chart for Common Bolt Sizes Pull out the gears and check the broken parts. Bolt Head Identification Bolt Head Identification If the transmission shaft is broken, replace the shaft then assemble the gear box with... - Page 12 ROTARY TILLER COMPLETE ASSEMBLY SR. NO. DESCRIPTION ITEM CODE QTY. HEX HEAD BOLT M8X40 10260373 HEX HEAD BOLT M8X25 10260360 OIL LEVEL INDICATOR 10300117 GEAR COVER 10150032 BREATHER NUT 22X1.5 10280010 BREATHER VALVE 10190001 CASTLE NUT 30X1.5 10280093 CASTLE NUT 30X1.5 10280093 SPLIT PIN 4X65MM 10020055...
- Page 13 ROTARY TILLER COMPLETE ASSEMBLY SR. NO. DESCRIPTION ITEM CODE QTY. BUSH 17X32X64 10070173 RT TPL PLATE RHS 79780008 RT TPL PLATE LHS 79780007 HEX HEAD BOLT M16X65X2 10260378 DEPTH SKID ASSEMBLY LHS 79370002 DEPTH SKID BUSH 10070005 DEPTH SKID ASSEMBLY RHS 79370001 PTO SAFETY COVER 70010080...
- Page 14 SIDE PLATE & ROTOR ASSEMBLY SR. NO. DESCRIPTION ITEM CODE QTY. HEX HEAD BOLT M10x1.5Px35 10260353 DEAD HUB CAP 10150014 SIDE PLATE BIG DEAD HUB SIDE (8MM) 70080027 CASTLE NUT M30x1.5P 10280093 INTERNAL CIRCLIP B80 10390005 BEARING 6307 10050090 SPLIT PIN 1/8"x2.5INCH 10020097 DEAD HUB 10090033...
- Page 15 SINGLE SPEED (11X20) GEAR BOX ASSEMBLY REGULAR SINGLE SPEED GEAR BOX ASSEMBLY SR. NO DESCRIPTION ITEM CODE 10080001 GEAR BOX HOUSING (SINGLE SPEED)11X20 10290010 PINION SHAFT (SINGLE SPEED) BEARING 30207 10050100 CIRCLIP 72MM (INTERNAL) 10390022 10010001 OIL SEAL 35X72X10 10250018 PINION GEAR 11TX6 SPLINES 10050097 BEARING 30210...
-
Page 16: Slip Clutch Assembly
PTO SHAFT ASSEMBLY - SLIP CLUTCH TYPE SLIP CLUTCH ASSEMBLY DESCRIPTION S.No. DESCRIPTION T06X560 T04X510 T06X560 T04X510 S.No. COMPLETE PTO SHAFT 10310062 10310124 PRESSURE PLATE 10310128 10310136 CROSS JOURNAL SET 10310064 10310100 INTERNAL DISC 10310129 10310137 SPRING DOWEL PIN SET (SLIP CLUTCH PTO) 10210031 10210194 FRICTION LINING... -
Page 17: Delivery Checklist
DELIVERY CHECKLIST Dealer Pre-Delivery (Please Tick) Please Complete all Dealer information Below WARRANTY CARD 1. Dealer Pre-Delivery Checklist Dealer Information Customer Copy 1. The customer or person responsible has Dealer’s Name................been given the operator’s manual. Address..................CUSTOMER NAME Mr./ Mrs : 2. - Page 18 WARRANTY CARD Company Copy CUSTOMER NAME Mr./ Mrs : ADDRESS MOBILE NO. Email NAME OF IMPLEMENT MODEL NO. YEAR OF Mfg. SERIAL NO. REGISTRATION NO. DATE OF PURCHASING NAME OF DEALER Customer`s Signature Dealer`s Signature DARRELL HARP ENTERPRISES Inc. 819 4th Street NW, PO Box 140, Red Bay, AL 35582, USA 256.356.4670 dheparts@bellsouth.net.
- Page 19 WARRANTY CARD Dealer Copy CUSTOMER NAME Mr./ Mrs : ADDRESS MOBILE NO. Email NAME OF IMPLEMENT MODEL NO. YEAR OF Mfg. SERIAL NO. REGISTRATION NO. DATE OF PURCHASING NAME OF DEALER Customer`s Signature Dealer`s Signature DARRELL HARP ENTERPRISES Inc. 819 4th Street NW, PO Box 140, Red Bay, AL 35582, USA 256.356.4670 dheparts@bellsouth.net.
- Page 20 DARRELL HARP ENTERPRISES Inc. 819 4th Street NW, PO Box 140, Red Bay, AL 35582, USA 256.356.4670 dheparts@bellsouth.net. www.darrellharp.com...
Need help?
Do you have a question about the Gear Drive 6 Tines and is the answer not in the manual?
Questions and answers