Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Boyo Vision VTBSD1
- Page 1 MICROWAVE RADAR BLIND SPOT DETECTION SYSTEM User’s Manual VTBSD1 Version：V1.0...
-
Page 2: Table Of Contents
Catalog Components ..................1 System Specification ................ 2 Install Caution ................3 III. Requirements for Radar Sensor Setting ........3 Installation Diagram ................3 Wires Connection Diagram ............4 Installation Gist ................5 VII. Parts Recovery ................11 VIII. Operation Instruction ..............11 Usual malfunction elimination............ -
Page 3: Components
Foreword Thanks for using our BSD system. The System is designed for universal cars, please read this product manual carefully for installing and uninstalling the product. I. Components ITEM PICTURE Main harness 1PCS Sensor 2PCS LED indicator 2PCS Buzzer 1PCS Instruction 1PCS manual... -
Page 4: System Specification
II. System Specification Item Specification 2pcs Radar Sensors System Configuration 2pcs LED Indicator lights 1pcs Buzzer Compliance ISO17387:2008 Detection Rang Accuracy ± 0.25m（Typical) Truck：0.3m～15m; Car ：0.3m～15m; Max. Detection Range Motorcycle ：0.3m～10m; Pedestrian：0.3m～7m; Alert Range 0.3m~15m System Car：≥98% Alert Accuracy Motorcycle：≥95% Pedestrian：≥95% HMI(Human Machine Level 1:LED Stay lit... -
Page 5: Install Caution
III. Install Caution Please release negative power before operation. Do not pull the harness when removing the connector, insert the connector to the buckle until a sound. Harness should be fixed with car harness by cable tie. The installation and disassembly should follow the vehicle maintenance manual and relative operating instruction. -
Page 6: Wires Connection Diagram
VI. Wires Connection Diagram 1. BSD_L connect to left sensor of BSD 2. BSD_R connect to right sensor of BSD 3. LED_L connect to Left LED indicator 4. LED_R connect to right LED indicator 5. L_Lamp connect to left rear lamp (left turn light) 6. -
Page 7: Installation Gist
VII. Installation Gist Sensor settings Step1. Sensors of the BSD system should be pasted to both inner corners of rear bumper shell with an angle of 25° to 35° , at height of 35-90cm.(Fig.1-Fig.3). Fig.1~Fig.3 Step2. Place a straight tape between front wheel and rear wheel, then place a 30º... - Page 8 Fig.4-Fig.6 Step4. Mark down the position ruler against the bumper with a marker (Fig.7-Fig.9). Fig. 7 Fig. 8 Fig. 9...
- Page 9 Step5. Mark down the position with same method for the other side of bumper (Fig.10). Fig. 10 Step6. Take off the plastic rear bumper (be aware of scratching on the bumper)(Fig.11-Fig.12). Fig. 11 Fig. 12 Step7. Clean the installation location of sensor with alcohol (Fig.13-Fig.14).
- Page 10 Step8. Prepare 2 pieces of magnetic metal; place one on the line marker outside the bumper and the other one on the corresponding spot inside of it. Mark the location with the marker. (Fig.15-Fig.17) Fig.15 Fig. 16 Fig. 17 Step9. Clean the plastic surface of the sensor with alcohol and then place a 3M adherent tape on the sensor (Fig.18-Fig.19).
- Page 11 Step12. The wiring scheme of sensor please refer to Fig.21, allow some adjustments due to different cars. Fig. 21 Installation of left/right signal lights harness Step13. Take out the reversing lamp, turn on the right signal light, the right-turn signal light is on, find out the 12v power cable with multi-meter, connect the R_LAMP in harness cable with the 12v power cable, and connect the L-LAMP in harness cable with the left side power cable.
- Page 12 Installation of LED lights Step14. LED Light is installed at left/right side of A pillar (Fig. 25-Fig. 图 25 图 26 Installation of Buzzer Step15. The buzzer should be pasted and hidden inside the panel. (Fig. 27) Fig. 27 Step16. Run the wires based on the installation diagram.
-
Page 13: Parts Recovery
VIII. Parts Recovery Step1. Confirmation of installation condition 1. The wiring and installation shall be checked prior to power connection 2. Be cautious whether there is excessive pressure, stretch or getting stuck with the wires Step2. Power supply recovery 1. Connect the negative terminal of battery (-) to make sure it functions well. - Page 14 When the system is on, the system would start detecting objects in the blind area behind the vehicle (Fig. 30). A. Blind detection on right side： Right LED indicator will turn on and stay lit when there is object approaching on the right blind area (3m X 15m). If the right signal light is turned on at this time, the right LED indicator will keep blinking and the buzzer will be on with sound beeping.
-
Page 15: Usual Malfunction Elimination
X. Usual malfunction elimination Malfunction Reason Solution Wrong connection or Check the harness LED light missed connection on and make sure doesn’t work harness connection is correct LED light is broken Replace LED light Contrary Contrary connection Exchange the alarm on of BSD_L and BSD_R connection of BSD_L right/left...
Need help?
Do you have a question about the VTBSD1 and is the answer not in the manual?
Questions and answers