Advertisement
Quick Links
877775A_
DTS DUAL CONSOLE REMOTE CONTROL
WITH CAN TRACKPAD
After completing installation, these instructions should be placed with the product for the owner's
future use.
This document is written to aid our dealers and company service personnel in the proper installation
or service of our products. Persons who are not familiar with these or similar products produced
by Mercury Marine, and who have not been trained in the recommended servicing or installation
procedures should have the work performed by an authorized Mercury Marine dealer technician.
Improper installation or servicing of the Mercury product could result in damage to the product or
personal injury to the installer or persons operating the product.
Installation of this product will require electronic calibration. This calibration must not be attempted
by anyone other than the Original Equipment Manufacturer (OEM) or a Mercury technician trained
in Digital Throttle and Shift systems (DTS) at an authorized Mercury dealership. Improper installation
and calibration of the DTS product will result in a system which is inoperable or unsafe for use.
Components Contained in Kit
Ref.
1
2
3
4
5
6
7
8
9
90-889224 MAY 2006
This Product Requires Electronic Calibration Before Use.
1
2
Qty.
1
Electronic Remote Control (ERC)
2
Cover - with gasket
1
Lanyard switch kit
4
Screw - M4 x 20
4
Screw - M6 x 40
4
Washer
4
Nut - M6, Nylon insert
1
Wrench - Allen 2.5 mm
1
Wrench - Allen 5 mm
© 2006 Mercury Marine
NOTICE
NOTICE
Notice
4
3
5
8
6
9
7
8792
Description
Part Number
NSS
877752A1
NSS
10-877754
10-40088-40
12-40023-16
11-40138-6
NSS
NSS
Page 1 / 17
Advertisement
Related Manuals for Mercury 877775A Series
Summary of Contents for Mercury 877775A Series
- Page 1 Mercury Marine, and who have not been trained in the recommended servicing or installation procedures should have the work performed by an authorized Mercury Marine dealer technician. Improper installation or servicing of the Mercury product could result in damage to the product or personal injury to the installer or persons operating the product.
-
Page 2: Remote Control Installation
DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD Remote Control Installation Required Mounting Clearances for DTS Dual Handle Control with CAN Trackpad 22633 Hand clearance Locating and Drilling Mounting Area for DTS Single/Dual Handle Console Control 1. Locate area of boat where the remote control is to be mounted. Allow sufficient clearance for handle movement and clearance for the wiring. - Page 3 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD IMPORTANT: After cutting mounting area, make sure opening is free of sharp edges. 3508 Template Installing the Dual Console Control with CAN Trackpad 1. Ensure the opening is free of sharp edges. 2.
- Page 4 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD IMPORTANT: Allow slack in the trim button harness going to the control handle. This harness will flex and move during control handle movement. 22524 Bayonet ends Starboard engine Trim button harness Port engine Blue paint dot Weather cap Yellow paint dot...
- Page 5 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD 7. Fasten the remote control with four M6 x 40 screws. 22127 Mounting Screw (4) M6 x 40 Nut - nylon insert Washer CAUTION Do not turn control handle tension adjustment screw clockwise more than 11 turns from the initial point of hex head contact with bracket.
- Page 6 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD 10. Install the side cover with attaching screws. 22129 Side cover (2) Attaching screws (4) M4 x 20 Dual Console Control with CAN Trackpad Features and Operation Dual Handle Console Control with CAN Trackpad Features and Operation 1.
- Page 7 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD 4. Troll button - Pressing the "TROLL" button activates troll control. The troll control feature allows the boat operator to set the engine speed for slow speed cruising or maneuvering. To activate, move the control handles into forward detent and press the button.
-
Page 8: Helm Transfer
DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD 11. Detent tension adjustment screw - This screw can be adjusted to increase or decrease the effort to move control handle out of detent positions (cover must be removed). Turning the screw clockwise will increase tension. Adjust to tension desired. ob01170 Detent tension adjustment screw Control handle tension adjustment... - Page 9 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD Once the "TRANSFER" button is pressed, the transfer LED will light up and one beep will sound. Press the "TRANSFER" button again to complete the helm transformation. When helm transformation is complete, another beep will sound and the transfer LED will turn off.
- Page 10 2. Ensure that the ignition key switch is in the "RUN" position, and that the CDS tool is communicating with the command module. NOTE: If the red Mercury SmartComm icon is flashing, the system cannot establish a connection with the SmartComm interface box. If the yellow Mercury SmartComm icon is flashing, the SmartComm interface box is detected, but communication with the command module cannot be established.
- Page 11 2. Ensure that the ignition key switch is in the "RUN" position, and that the CDS tool is communicating with the command module. NOTE: If the red Mercury SmartComm icon is flashing, the system cannot establish a connection with the SmartComm interface box. If the yellow Mercury SmartComm icon is flashing, the SmartComm interface box is detected, but communication with the command module cannot be established.
- Page 12 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD 4. All the CAN trackpads connected to the system should start flashing. Verify they are all flashing and press the "Yes" button. If any trackpads are not flashing, press the "No" button. 5.
- Page 13 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD Notes: 90-889224 MAY 2006 Page 13 / 17...
- Page 14 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD DTS Dual Engine Single Helm with CAN Trackpad Console Control Page 14 / 17 90-889224 MAY 2006...
- Page 15 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD Port engine Starboard engine Engine CAN 2 connector (brown and yellow) - blue terminator resistor Engine CAN 1 connector (blue and white) - yellow terminator resistor 14 pin data harness Command module harness CAN 1 link harness - 2 pin CAN 2 connector (brown and yellow) - blue terminator resistor CAN 3 connector (orange and green) - weather cap...
- Page 16 DTS DUAL CONSOLE REMOTE CONTROL WITH CAN TRACKPAD Notes: Page 16 / 17 90-889224 MAY 2006...
- Page 17 Products of Mercury Marine Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser, Mercury Racing, Mercury Precision Parts, Mercury Propellers, Mariner, Quicksilver, #1 On The Water, Alpha, Bravo, Pro Max, OptiMax, Sport-Jet, W6250 Pioneer Road K-Planes, MerCathode, RideGuide, SmartCraft, Zero Effort, M with Waves logo, Mercury with Waves logo, and SmartCraft logo are all registered trademarks of Brunswick Corporation.
Need help?
Do you have a question about the 877775A Series and is the answer not in the manual?
Questions and answers