Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Air Live SI-104
- Page 1 SI-104 Smoke Sensor User Manual...
- Page 2 This product contains some codes from GPL. In compliance with GPL agreement, AirLive will publish the GPL codes on our website. Please go to www.airlive.com and go to the "Support->GPL" menu to download source code. All Trademarks are properties of their respective holders. AirLive SI-104 User Manual...
- Page 3 When replacing old appliances with new once, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge. AirLive SI-104 User Manual...
-
Page 4: Table Of Contents
1.8 Tamper Switch Feature ..............5 1.9 Battery Installation ................6 1.10 Choosing a Suitable Location ............6 1.11 Installation ..................8 1.12 Z-Wave Configuration Settings ............9 1.13 Z-Wave Supported Command Class ..........9 1.14 Specifications ................. 10 AirLive SI-104 User Manual... -
Page 6: Overview
1. Overview Overview The Z-Wave Plus Smoke Sensor SI-104 is designed to give early warning of developing fires by giving off the alarm sounds from its build-in alarm horn, based on Z-Wave technology. It is the Z-Wave plus product, it support the security, OTA... those newest features of the Z-Wave technology. -
Page 7: Add To/Remove From Z-Wave Tm Network
These groups support 8 nodes maximum. Failed or success in add/remove the node ID can be viewed from Z-Wave Controller. Z-Wave Z-Wave Notice 1: Always RESET a device before trying to add it to a network. AirLive SI-104 User Manual... -
Page 8: Z-Wave Tm Notification
Smoke Alarm Test (0x03) Sensor Binary Report (V2) Sensor Type: Smoke (0x02) Sensor Value: 0xFF 1.3.2. Tamper Report When the tamper is pressed, the device will into the alarm state. In that state, if tamper is AirLive SI-104 User Manual... -
Page 9: Power Up Procedure
Please don't remove the battery, otherwise it will cause the firmware broken, and the device will no function. After updated finish, it is recommended that the user power up the device. Caution: After remove the battery, please wait about 30 seconds, and then re-install the battery. AirLive SI-104 User Manual... -
Page 10: Security Network
If the Smoke Sensor is not mounted into the bracket properly, the tamper function is triggered and the yellow LED is steadily on. You will hear temporal three sound with yellow LED steadily on until Smoke Sensor is mounted back into bracket properly. AirLive SI-104 User Manual... -
Page 11: Battery Installation
2. If ceiling mounting is not possible, put wall-mounted sensors between 4 and 6 inches(10~15 cm) from the ceiling. 3. If some of your rooms have sloped, peaked, or gabled ceilings, try to mount sensors 3 feet(0.9 meter) measure horizontally from the highest point of ceiling. AirLive SI-104 User Manual... - Page 12 Additionally, dust or dirt can block openings to the sensing chamber and keep the alarm from sensing smoke. ※ Near fluorescent lights, electrical “noise” from fluorescent lights may cause nuisance alarms. Install Smoke Sensor at least 5 feet (1.5 meters) from such lights. AirLive SI-104 User Manual...
-
Page 13: Installation
Attach the bracket to the wall. Line up the slots of the bracket and the Smoke Sensor. Push the sensor onto the mounting bracket on turn it clockwise to fix it into the place. Pull onward on the Smoke Sensor to make sure it is securely attached to the mounting bracket. AirLive SI-104 User Manual... -
Page 14: Z-Wave Configuration Settings
0 means turn off auto report battery. Each tick means 30 minutes. The default value is 12 (6 hours). 1.13 Z-Wave Supported Command Class COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_SENSOR_BINARY_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_SECURITY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 AirLive SI-104 User Manual... -
Page 15: Specifications
1. Overview 1.14 Specifications Power by CR123A lithium battery. Signal (Frequency): SI-104: 868.40 MHz, 869.85 MHz(EU), SI-104: 908.40 MHz, 916.00 MHz(US), SI-104: 922~927 MHz(JP/TW), SI-104: 921.40 MHz, 919.80 MHz(ANZ), SI-104: 869.00 MHz(RU), SI-104: 865.20 MHz(IN), SI-104-IL:916.00 MHz(IL), Range: Minimum 40 meters indoor, 100 meters outdoor line of sight.
Need help?
Do you have a question about the SI-104 and is the answer not in the manual?
Questions and answers