Quoizel MBH8411PN Assembly Instruction Sheet

6 CORPORATE PARKWAY
, .
GOOSE CREEK SC 29445
. .
www quoizel com
Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended: (3) Candelabra Base 60W Maximum, Alternate bulb (3) 13W CFL
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Fixture
A Body
x 1
Tab
B
x 2
Hardware Contents
-
STEP 1 Install Shade
A. Place Glass Shade (C) into the Cage
(D), secure by place the Tab (B) into
the Cage (D) press on the Glass
Shade (C).
B. Set the Cage (D) with Glass Shade
(C) into the Cap on the Fixture Body
(A), secure by threading the Lock
Screw (E) into the Cap, tighten until
sung.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2015 QuoizelInc.
Assembly Instruction Sheet #IS-MBH8411
For Style
for product cleaning tips. Go to the
30-45 minutes
Glass Shade
C
x 1
Cage
D
x 1
E
Crossbar Assembly
AA
x 1
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
MBH8411PN
Care + Maintenance selection.
-
STEP 2 Install Inner Backplate
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug.
Outlet Box
Lock Screw
x 3
Figure 2
-
STEP 3 Fit Fixture Body to
Crossbar Assembly
A. Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Fixture Body (A) Crossbar
Assembly (AA) and secure with
mounting balls. Note: The
backplate of the Fixture Body (A)
should be snug against the wall
surface and the mounting balls. If
not, adjust the length of the nipple
on the Crossbar Assembly (AA) by
A
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in or
out of the crossbar until the correct
length is achieved. Once the
backplate of the Fixture Body (A) is
B
secure, remove the mounting ball
and Fixture Body (A) and proceed
to Step 4.
C
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
E
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
D
1of2
and MBH8411K
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Mounting
Ball
A
Hex Nut and
Lock Washer
AA
Mounting
Screw
Figure 3
January2015