Advertisement
Quick Links
FEB/FEC(E-TTL only)
1. FEB (Flash Exposure Bracketing)
Ÿ
Support 1/3-stop increments to set FEB within ±3.
※ The sequence of FEB is fixed at 0→ -→ +， even
sequence of the custom setting in flash is different, the
shoot sequence remains to 0→-→+ either.
※ F E B f u n c t i o n w i l l b e a u t o m a t i c a l l y c a n c e l l e d a f t e r
three shots are taken.
※ Even the E-TTL flash does not support FEB can also
realize this function.
2. FEC (Flash Exposure Compensation)
Ÿ
Support 1/3-stop increments to set FEC within ±3. The FEC
button of the camera can also be use.
Setting value will be show on the flash screen when half-
!
pressing the shutter button. Till FEB and FEC of the flash are
set to 0, settings could be changed by remote control of
camera menu , and you can also set each of the flash FEB and
FEC via its control panel, compensation value shall be
superposed according to flash setting plus camera menu
setting, for example, the camera menu is set to -3, and the
flash is set to +3, then exposure compensation shall be 0.
14
the FEB
Advertisement
Summary of Contents for Yongnuo YN622CII
- Page 1 FEB/FEC(E-TTL only) 1. FEB (Flash Exposure Bracketing) Ÿ Support 1/3-stop increments to set FEB within ±3. ※ The sequence of FEB is fixed at 0→ -→ +， even the FEB sequence of the custom setting in flash is different, the shoot sequence remains to 0→-→+ either.
-
Page 2: Zoom (Flash Coverage)
Zoom (Flash Coverage) Zoom supports automatic/manual setting. Ÿ 1. With automatic setting, focal length of the flash may change with lens focal length. 2. With manual setting, focal length of the flash supports manual setting within 24-105MM. 1. Automatic Setting 2. - Page 3 Manual Flash / Multi Flash 1.Manual Flash: Manually set flash output (1/128~1/1 power 1/3-stop increments) Select flash mode as Manual Flash Mode, setting Ÿ flash output ,shutter sync, zoom etc. 2.Multi Flash (Stroboscopic flash) Select flash mode as Multi Flash, setting via the Ÿ...
-
Page 4: Wireless Function
Wireless Function* By setting the wireless flash function menu, in a different Ÿ flash mode or firing group, remotely set A / B / C, three groups of flash ratio or flash output. 1. Enabled the wireless function via flash control menu. 2. - Page 5 Wireless Function 3.Channel Setting via Wireless Function Set channel (CH1-CH4 only) of the transmitter via wireless function setting, the changed shall cover the original setting. CH1-CH7 may also be set by directly pressing [CH SET] at the transmitter(p.8). 4. Firing Group Setting via Wireless Function Sets firing group of the transmitter via wireless function setting, in transmitting communications, state indicator and...
- Page 6 Flash Ratio with E-TTL II Flash fire ratio and FEC of the A, B, C three firing Ÿ groups can be under E-TTL II flash mode. 1.All (A+B+C) R a t i o o f f, A / B / C t h r e e flashes automatically fire with same output, flash e x p o s u r e c o m p e n s a t i o n...
- Page 7 Manual/Multi Flash Output Flash output for each group A/B/C can be Ÿ separately set under Manual/Multi flash mode. 1. All (A+B+C)-The three groups of flashes shall be set with the same output. 2. A: B-Group A and B shall be separately set Group C flash will not fire.
- Page 8 Mix Control Mode Ÿ Set the flash on each receiver in different flash modes as Manual/E-TTL/Multi for mix control, the settings of the flash is prior , channel indicator of the transmitter will keep lighting when enabled this control mode. Supports type A/B cameras using.
- Page 9 Flash Triggering of B/C Type Camera Type B Cameras: There is no flash control menu of such type of cameras Ÿ that some of function will be restricted. Enable the mix control mode of the transmitter before using(P.21). 1. Setting of transmitting groups (set in the transmitter when it in transmitting status): Half press the camera’s shutter button then status indicator blinks green.
- Page 10 PC Port Triggering (Support Super Sync *) Caution! Do not connect to the PC port any flash requiring trigger voltage more than 300V, or the transceiver may be damaged. Ÿ Purchase corresponding PC flash sync cord according to the different ports of the flashes needs . 1.
- Page 11 References AF Assist Beam Emitter When using AF under low-light, Ÿ built-in AF-assist beam emitter of the transmitter will be emitted automatically to make it easier to autofocus, and the flash on the transmitter which support AF assist beam emitter function can also be emitted at the same time.
- Page 12 Reference-About 560-RX The YN622C II supports receiving the triggering signal YN560-TX (RF603 communication mode),when using the compatible flash, it can wireless control the flash mode, flash output and zoom of each group; meanwhile supports the triggering signal(the flash set to M mode) of the RF603(II)、...
- Page 13 References Firmware Update 1.Log in the YONGNUO official website: http://www.hkyongnuo.com/e-detaily.php?ID=364 to download the firmware update software and the latest firmware. 2.Power off, use Micro-USB(do not include) cable connect to PC. 3.Press the <CH SET> button and set the power on, all the indicator bright(green).
-
Page 14: Troubleshooting
Troubleshooting 1. Fail to power on or automatic shutdown: The batter y is loaded inversely or exhausted; the status Ÿ indicator light will blink(red) separately when the batter y is going to be exhausted, and it will power off automatically in case of being over discharged. - Page 15 Troubleshooting 6. The assist beam emitter doesn't work : Refer to page 24. 7. The on-top flash doesn't fire: Enabled the master flash via the wireless function setting. 8. Can't set the flash zoom via camera menu: W h e n t h e m i x control mode has been set in the transmitter (p.21) or zoom locking has been set in the receiver (p.15), zoom can't be set via camera menu.
-
Page 16: Specifications
Specifications System type: Digital FSK 2.4GHz wireless transceiver Distance: 100M Channel: 14 Flash mode: E-TTL(II), Manual flash, Multi flash Sync mode: 1st curtain, 2nd curtain, Hi-speed sync Groups: A/B/C 3Groups(622);A/B/C/D/E/F 6Groups (560-RX) Max Sync speed: 1/8000s* Input: Hot-shoe(TTL,main contact) Output: Hot-shoe, PC port Firmware upgrade terminal: Micro USB Applicable batter y: AAX2 (support 1.2 V rechargeable batter y) - Page 17 FCC ID: 2ACYPYN622CII This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.