Related Manuals for ADVATEK LIGHTING PixLite R4D-S
Summary of Contents for ADVATEK LIGHTING PixLite R4D-S
- Page 1 PixLite R4D-S User Manual Hardware Rev 1.3 - 1 - www.advateklights.com PixLite R4D-S User Manual V220317...
-
Page 2: Table Of Contents
7.1 - Operating Specifications 7.2 - Mechanical Specifications 7.3 - Fault Protection 8 - Troubleshooting 8.1 - No Power LED 8.2 - No Pixel Control 8.3 - Other Issues 9 - Disclaimer - 2 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 3: Introduction
2 - Introduction This is the user manual for the PixLite R4D-S pixel receiver, hardware version 1.3. The PixLite R4D-S is designed to receive differential long distance signals of 300m (1000') or more over a standard network cable from a PixLite T8 transmitter unit, and convert these input signals back into a pixel-ready signal for output directly to pixels. -
Page 4: Safety Notes
This LED pixel receiver should be installed by someone with proper technical knowledge only. Installation of the device and/or replacement of pixel output fuses should not be attempted without such knowledge. Specification and certification markings are located on the of the device. - 4 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 5: Physical Installation
(not supplied). The screws should be a pan head type, 3mm in thread diameter and at least 15mm long, as shown in Figure 1 below. Figure 1: receiver Assembled to Wall - 5 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 6: Din Rail Mount
1. Align the receiver's mounting holes with the outermost mounting holes on each bracket. Using the four supplied M3, 12mm long screws, assemble the receiver to the mounting brackets, as shown in Figure 2 below. Figure 2: receiver Assembled to Bracket - 6 - www.advateklights.com PixLite R4D-S User Manual V220317... - Page 7 2. Align the lower edge of the bracket with the lower edge of the DIN rail (1), and push the receiver down so it clicks onto the DIN rail (2), as shown in Figure 3 below. Figure 3: receiver Assembled to DIN Rail - 7 - www.advateklights.com PixLite R4D-S User Manual V220317...
- Page 8 3. To remove the receiver from the DIN rail, pull the receiver horizontally, toward its power connector (1) and rotate the receiver up and off the rail (2), as shown in Figure 4 below. Figure 4: Removal of receiver from DIN Rail - 8 - www.advateklights.com PixLite R4D-S User Manual V220317...
-
Page 9: Electrical Connections
5 - Electrical Connections 5.1 - Supplying Power Power is applied to the PixLite R4D-S via the large lever clamp connector. The levers should be lifted up for wire insertion and then clamped back down, providing a highly robust and secure connection. Ensure the wire’s insulation is stripped back 11-12mm, so that the clamp does not rest on the insulation when closing the connector. -
Page 10: Data Input
Figure 6 below. Figure 6: Internal View of the PixLite R4D-S No on- board power configuration is required. Power to the logic circuitry is automatically regulated from the power input. Simply connect your DC power supply in accordance with specifications listed in Section 7.1... - Page 11 For this reason, the standard network cable you use can be safely used in excess of 300m. Figure 8: Correct equipment to use A typical setup is shown in Figure 9 below, which also shows how many pixels can be run off each output. - 11 - www.advateklights.com PixLite R4D-S User Manual V220317...
-
Page 12: Connecting Pixel Leds
4) and on the top of the lid the pin-out is clearly marked. Simply wire your lights into each screw terminal and then plug them into the mating sockets. Since the PixLite R4D-S product has data only outputs (no pixel clock lines), it takes advantage of the transmitter's Expanded Mode. In expanded mode, the clock lines are used as data lines instead. -
Page 13: Operation
If the switch is pushed to the right, it is off, and all indicator LEDs and the power LED will always be off. This switch is shown in Figure 12 below. - 13 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 14: Outputs
Refer to the user manual of the PixLite Transmitter device for more information about this topic as the Transmitter will be responsible for the refresh rate of this receiver. - 14 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 15: Specifications
7 - Specifications 7.1 - Operating Specifications The table below specifies the recommended operating conditions for a PixLite R4D-S receiver. Parameter Value/Range Units Input Voltage Range 5-24 V DC Max Current Max Logic Current Consumption @ 5V Ambient Operating Temperature -20 to +55 °C... -
Page 16: Fault Protection
Figure 13: Receiver Mechanical Specifications 7.3 - Fault Protection The PixLite R4D-S features notable protection from potential damage due to various types of faults. This makes the device extremely robust and reliably able to withstand installation and operation even in harsh environments. -
Page 17: Troubleshooting
If you can’t resolve your problem with the help of our knowledgebase, you can send an e-mail to: support@advateklights.com and a support ticket will automatically be created for you, or you can manually open a support ticket here: www.advateklights.com/support - 17 - www.advateklights.com PixLite R4D-S User Manual V220317... -
Page 18: Disclaimer
EN 55024 Power Frequency Magnetic Field Immunity EN 61000-4-8 Restriction of Hazardous Substances RoHS 3 Through testing to the above standards, the PixLite R4D-S has the certifications and marks listed in the table below. Certification Relevant Country ETL Listing North America and Canada. Equivalent to UL Listing. - Page 19 This product has been manufactured by: Advatek Lighting Pty Ltd 16 / 52 Corporate Blvd Bayswater, 3153 VIC, AUSTRALIA - 19 - www.advateklights.com PixLite R4D-S User Manual V220317...
Need help?
Do you have a question about the PixLite R4D-S and is the answer not in the manual?
Questions and answers