Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CROWN VERITY ZCV-2650-SS
Summary of Contents for CROWN VERITY ZCV-2650-SS
-
Page 2: Package Contents
PACKAGE CONTENTS QUANTITY Reflector Panel Head Assembly Cylinder Housing Door (preassembled) Post Gas Hose Regulator Bucket (preassembled) Wheel Kit Base... -
Page 3: Safety Information
HARDWARE CONTENTS (shown actual size) M6 Nut M8 Nut M5 x 8 mm Qty. 8 Qty. 2 Φ6 Screw M6 x 10 mm M6 x 12 mm Small Flat Φ8 Washer Qty. 4 Bolt Bolt Washer Qty. 11 Qty. 4 Reflector Qty. - Page 4 SAFETY INFORMATION DANGER DANGER • CARBON MONOXIDE HAZARD • EXPLOSION - FIRE HAZARD • This heater is a combustion appliance. All • Keep solid combustibles, such as building combustion appliances produce carbon materials, paper or cardboard, a safe distance monoxide (CO) during the combustion away from the heater as recommended by the process.
-
Page 5: Burn Hazard
SAFETY INFORMATION WARNING WARNING We cannot foresee every use that may be Do not store or use gasoline or other flammable made of our heaters. vapors and liquids in the vicinity of this or any Check with your local fire safety authority if you other appliance.An LP-cylinder not connected have questions about heater use. -
Page 6: Service Safety
SAFETY INFORMATION WARNING WARNING • This product is fueled by propane gas. Propane • Alert children and adults to the hazards of gas is invisible, odorless, and flammable. An high surface temperatures. Stay away from odorant is normally added to help detect leaks these surfaces to avoid burning skin or and can be described as a “rotten egg”... - Page 7 ASSEMBLY INSTRUCTIONS 1. Assemble the wheel bracket to the base with 4pcs STEP 1 M6X12 bolt (BB) and 4pcs M6 nut (AA). (see step 1). Assemble the other bracket in the same way. Assemble the wheel to the bracket with 1pc M8X45 bolt (DD), 1pc Φ8 Washer (HH) and M8 Nut (CC) (see step 2).
- Page 8 ASSEMBLY INSTRUCTIONS 4. Secure post (E) to cylinder housing (C) using the reinforced ring (MM), M6 x 10 mm bolts (FF) and Φ6 small flat washers (GG). Fasten and cover with the deco ring (NN). Hardware Used M6 x 10 mm Bolt Φ6 Small Flat Washer Reinforced Ring Deco Ring...
- Page 9 ASSEMBLY INSTRUCTIONS 7. Slide Φ8 washers (HH) over the threaded ends of reflectors spacers(II). Attach reflector assembly to head assembly (B). Place Φ8 washers (HH) over threaded ends of reflector spacers(II) sticking out through reflector assembly and secure with wing nuts (JJ). Note: Do not overtighten.
- Page 10 ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S.
- Page 11 OPERATION INSTRUCTIONS To check for a leak: WARNING 1. Make 2-3 oz. leak check solution (one part liquid dishwashing detergent and three parts • Perform all leak tests outdoors. water). • Extinguish all open flames. 2. Apply several drops of solution where •...
- Page 12 OPERATION INSTRUCTIONS DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Caution: Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed.
- Page 13 OPERATION INSTRUCTIONS Lighting: 1. Turn on the valve on the gas cylinder. 2. Press and turn the control knob to HIGH (maximum) position (anti-clockwise 90º). (Figure 1) 3. Holding down the control knob, press the igniter button several times until the main flame is ignited. Release the control knob 10 seconds after the ignition.
-
Page 14: Operation Checklist
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When Heater is ON: Emitter screen will become bright red due to intense heat. -
Page 15: Care And Maintenance
OPERATION INSTRUCTIONS Heater is away from gasoline or other flammable liquids or vapors. Heater is away from windows, air intake openings, sprinklers and other water sources. Heater is at least 24 in. on top and at least 36 in. on sides from combustible materials. Heater is on a hard and level surface. - Page 16 CARE AND MAINTENANCE Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and render it unsafe for use.
-
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 1. Wait until the propane cylinder 1. Propane cylinder is frosted over warms up and becomes unfrosted Burner won’t light 2. Blockage in orifice 2. Clear blockage 3. Control knob is not in ON position 3. -
Page 18: Replacement Parts List
REPLACEMENT PARTS LIST QUANTITY Reflector Panel Head Assembly Cylinder Housing Door (preassembled) Post Gas Hose Regulator Bucket (preassembled) Wheel Kit Base Printed in China...
Need help?
Do you have a question about the ZCV-2650-SS and is the answer not in the manual?
Questions and answers