Summary of Contents for IntraServer Technology ITI-2135
- Page 1 ITI-2135 and ITI-2147 PCI Bridged Riser Cards Installation Guide Part Number: 90-100260 A01 March 2000...
- Page 2 ITI-2135 and ITI-2147 PCI Bridged Riser Cards Installation Guide Part Number: 90-100260 March 2000 Revision/Update Information: A01 - Initial Release...
-
Page 3: Table Of Contents
Organization of this Guide Overview of the Riser Cards Power and Dimensional Specifications Block Diagram Riser Card Layout Diagram Installing the ITI-2135 and ITI-2147 PCI Bridged Riser Cards System Requirements Installing the Riser Cards List of Tables List of Figures... -
Page 4: Introduction
Introduction This guide describes how to mount and install the ITI-2135 and ITI-2147 PCI Bridged Riser Cards in your system. Organization of this Guide This guide is organized in the following way: • Overview of the Bridged Riser Cards •... -
Page 5: Power And Dimensional Specifications
Power and Dimensional Specifications In order to operate the ITI-2135 or ITI-2147 Riser Card in your system, you must have an available PCI slot for the card. Block Diagram 64 Bit PCI Connector / Slot 2 64 Bit PCI Connector /... -
Page 6: Table 2: Power Available For All Slots Behind The Riser Card
CURRENT POWER (AMPS) (WATTS) 3.3V 11.9 39.3 -12V Table 2: Power Available For All Slots Behind The Riser Card Note: (1) Total power for any card in a slot is 25W max. (2) The system power supply may be a limiting factor. Slot IDSEL Device... -
Page 7: Table 4: Pci Bus Configuration And Specifications
PWRI/O Riser Conn. 21154- Card Type Band- bridge Cards Slots width variant Supprt Clock MB/sec 2135-5V 33 MHz 5V or universal fingers 2135-3V 3.3V 3.3V 66MHz 3V or universal fingers 2147-5V 33 MHz 5V or universal fingers 2147-3V 3.3V 3.3V 66MHz 3V or universal... -
Page 8: Riser Card Layout Diagram
Riser Card Layout Diagram C------------------- Slot 2 C ------------------ Slot 1 C ----------------- Slot 0 “0” NOT TO SCALE “0” 2135 2147 2.723 2.424 2.398 2.100 8.409 8.409 0.250 0.185 8.150 8.159 0.454 0.251 2.079 1.876 0.575 0.301 Slot 0 Center 1.375 1.101... -
Page 9: Installing The Iti-2135 And Iti-2147
This chapter describes how to install the ITI-2135 and ITI-2147 Riser Cards in your PCI based bus master compatible computer. The ITI-2135 and ITI-2147 Risers are Plug and Play on the host system’s PCI bus, and no configuration of the riser hardware is necessary. - Page 10 Locate a free PCI expansion slot (small white connector on the system’s motherboard) and remove the screw(s) and metal bracket(s) for the slot(s) to be filled by cards installed into the Riser Card. Be certain not to install the riser in an ISA or EISA slot.
-
Page 11: List Of Tables
List of Tables Table 1: Riser Cards included in this manual............4 Table 2: Power Available For All Slots Behind The Riser Card......6 Table 3: Interrupt Mapping ................6 Table 4: PCI Bus Configuration and Specifications ..........7 Table 5 : Riser Card Dimensions in Inches............8 List of Figures Figure 1: 92 Dual Position Connector with 3.3V Key ........12 Figure 2: 92 Dual Position Connector with 5V Key ........12... -
Page 12: Appendix A Connector Specifications
Specification for details regarding expansion board pinout assignment. The ITI-2135-3V and ITI-2147-3V utilize three (3) 92 dual position connectors with 3.3V key and the ITI-2135-5V and ITI-2147-5V utilize three (3) 92 dual position connectors with 5V key. Pin 1 3.3V Key... -
Page 13: Figure 3: 3.3V Riser Card Component Side
Pin 1 21154-* PCI-PCI Bridge Gold Fingers Figure 3: 3.3V Riser Card Component Side Note: Connector Pin 1 location same for 5V Riser Card. -
Page 14: Product Warranty
PRODUCT WARRANTY LIMITED HARDWARE WARRANTY ITI warrants to only the original licensee that the Riser Card is free of defects in materials and workmanship under normal use for a period of three years from the date of purchase. In the event of a defect in Riser Card material or workmanship during such warranty period, ITI, at its discretion, will repair or replace the defective product when the defective product is returned to ITI by the original licensee. -
Page 15: Limitations
LIMITATIONS EXCEPT FOR THE WARRANTIES STATED IN THIS LIMITED PRODUCT WARRANTY, ITI SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ITI BE LIABLE FOR ANY LOSS OF DATA, PROFIT OR ANY COMMERCIAL DAMAGE, INCLUDING BUT NOT LIMITED TO SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR OTHER DAMAGES. - Page 16 Reader’s Comments Mail to: IntraServer Technology, Inc. Seven October Hill Road Holliston, MA 01746 Your comments and suggestions help us improve the quality of our publications. I rate this manual on: Excellent Good Fair Poor Accuracy (product works as manual says)
Need help?
Do you have a question about the ITI-2135 and is the answer not in the manual?
Questions and answers