Table of Contents
Advertisement
Quick Links
Installation Manual
RIVER RADAR
FR-1908V-BB/FR-1918V-BB
Model
SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATION ........................................................................................... ii
EQUIPMENT LISTS........................................................................................................ iii
1. MOUNTING..............................................................................................................1-1
1.1 Antenna Unit ......................................................................................................................1-1
1.2 Processor Unit ...................................................................................................................1-5
1.3 Control Unit ........................................................................................................................1-7
1.4 Monitor Unit........................................................................................................................1-7
2. WIRING....................................................................................................................2-1
2.1 Antenna Unit ......................................................................................................................2-2
2.2 Processor Unit ...................................................................................................................2-6
3. ADJUSTMENTS ......................................................................................................3-1
3.1 How to Open the Protected Menus....................................................................................3-1
3.2 How to Set Alarms .............................................................................................................3-2
3.3 How to Enter Your Ship's Characteristics ..........................................................................3-2
3.4 How to Adjust Sweep Timing .............................................................................................3-3
3.5 How to Adjust Video Level .................................................................................................3-4
3.6 Heading Alignment.............................................................................................................3-4
3.7 How to Suppress Main Bang .............................................................................................3-5
3.8 How to Set the Transmission Stop Area ............................................................................3-6
3.9 How to Set the Radar Antenna Position ............................................................................3-6
3.10 How to Set the GPS Antenna Position...............................................................................3-6
3.11 How to Adjust the ROT/Rudder/Autopilot Graph (Analog Input Only) ...............................3-7
APPENDIX 1 JIS CABLE GUIDE .............................................................................AP-1
APPENDIX 2 INITIALIZE MENU TREE ....................................................................AP-2
PACKING LISTS ......................................................................................................... A-1
OUTLINE DRAWINGS ................................................................................................ D-1
INTERCONNECTION DIAGRAM ................................................................................ S-1
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Advertisement
Table of Contents
Related Manuals for Furuno FR-1918V-BB
Summary of Contents for Furuno FR-1918V-BB
-
Page 1: Table Of Contents
Installation Manual RIVER RADAR FR-1908V-BB/FR-1918V-BB Model SAFETY INSTRUCTIONS ....................i SYSTEM CONFIGURATION ................... ii EQUIPMENT LISTS......................iii 1. MOUNTING......................1-1 1.1 Antenna Unit ........................1-1 1.2 Processor Unit ........................1-5 1.3 Control Unit ........................1-7 1.4 Monitor Unit........................1-7 2. WIRING........................2-1 2.1 Antenna Unit ........................2-2 2.2 Processor Unit ........................2-6... - Page 2 Installation Manual This page is intentionally left blank.
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS The installer of the equipment must read the safety instructions before attempting to install the equipment. Indicates a potentially hazardous situation which, if not DANGER avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not WARNING avoided, could result in death or serious injury. -
Page 4: System Configuration
SYSTEM CONFIGURATION Radiator ANTENNA UNIT XN20AF XN24AF - RSB-120-102 (4kW, FR-1908V-BB) - RSB-120-124 (12kW, FR-1918V-BB) Control Unit RW-0013 RCU-032 External Monitor - ROT Sensor (e.g. MU-190V) (Analog/Alarm) 24 VDC PROCESSOR - Auto Pilot (Analog/Follow-up) UNIT - Rudder (Analog) RPU-026 External Monitor... -
Page 5: Equipment Lists
Remarks Antenna Unit XN20AF-RSB-120-102 4kW, 2040 mm, 26 rpm (FR-1908V-BB) XN24AF-RSB-120-102 4kW, 2550 mm, 26 rpm Antenna Unit XN20AF-RSB-120-124 12kW, 2040 mm, 26 rpm (FR-1918V-BB) XN24AF-RSB-120-124 12kW, 2550 mm, 26 rpm Processor Unit RPU-026 Control Unit RCU-032 Installation CP03-34401 001-194-530... - Page 6 EQUIPMENT LISTS This page is intentionally left blank.
-
Page 7: Mounting
MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. Antenna Unit 1.1.1 Mounting considerations • The antenna unit is generally installed either on top of the wheelhouse or on the ra- dar mast, on a suitable platform. - Page 8 1. MOUNTING 1.1.2 How to assemble the antenna unit The antenna unit consists of the antenna radiator and the antenna unit chassis, and they are packed separately. Fasten the antenna radiator to the antenna unit chassis as below: 1. Attach two guide pins to the underside of the antenna radiator. 2.
- Page 9 1. MOUNTING 1.1.3 How to fasten the antenna unit to the mounting platform The antenna unit may be assembled before hoisting it to the mounting platform. How- ever, do not lift the antenna unit by the radiator. Always hold the unit by its housing. When using a crane or hoist, use the hoist rings which should be fastened to the bolt fixing covers of the antenna housing.
- Page 10 1. MOUNTING 5. Fasten the antenna unit to the mounting platform with M12x60 hex. bolts, nuts, flat washers and seal washers. 6. Use hex. bolt (M6x25), nut (M6) and flat washers (M6) to establish the ground sys- tem on the mounting platform as shown below. The location should be within 340 mm of the ground terminal on the antenna unit.
-
Page 11: Processor Unit
1. MOUNTING Processor Unit 1.2.1 Mounting consideration The processor unit can be mounted on a desktop or bulkhead. When selecting a mounting location, be careful about the following points: • Locate the unit out of direct sunlight and away from heat sources because of heat that can build up inside the cabinet. - Page 12 1. MOUNTING Bulkhead installation Note: The cable entry side should be downward when the processor unit is mounted on the bulkhead. 1. Mark location for four self-tapping screws if screws will be used. 2. Insert four bolts (M5, supplied) or self-tapping screws (5x20), leaving approx. 5 mm of the bolts (screws) exposed.
-
Page 13: Control Unit
• For monitors other than the MU-190V, brightness cannot be adjusted from the menu or the control unit. Adjust brightness at the monitor itself. • The output video signal from the FR-1908V-BB/FR-1918V-BB cannot be flipped up- side-down. For this reason, when installing a landscape monitor select a location that allows the monitor to be installed after rotating the monitor 90 degrees clock- wise. - Page 14 1. MOUNTING This page is intentionally left blank.
-
Page 15: Wiring
WIRING XN20AF ANTENNA UNIT XN24AF - RSB-120-102 (4kW, FR-1908V-BB) - RSB-120-124 (12kW, FR-1918V-BB) Monitor unit Monitor unit (e.g. MU-190V) (e.g. MU-190V) DVI cable USB cable 24 VDC 24 VDC Control Unit USB mouse Processor unit - Echo sounder RPU-026 - Compass... -
Page 16: Antenna Unit
2. WIRING Antenna Unit CAUTION The magnetron in the transceiver module will demagnetize if it contacts ferrous material. When dismounting the transceiver module, lay it on its side or on top of non-ferrous material as shown below. Transceiver module (magnetron inside) Non-ferrous block Height more... - Page 17 2. WIRING 2) Unravel the outer shield to expose the cores in the outer layer. Then, expose the cores in the inner layer. Label all inner cores to aid in identification. 3) Trim each core (except coaxial wire) considering its location on the terminal board.
- Page 18 2. WIRING 10. Connect the signal cable to the terminal board TB801, TB802 and TB803 on the 03P9488 board, referring to the interconnection diagram. Terminal opener 03P9488 board TB803 (High-Voltage line) How to insert the core 1. Push white lever. 2.
- Page 19 2. WIRING 12. Detach the junction box from the transceiver unit. Junction box Fixing screw Core-fixing screw Coaxial cable Shield-fixing clamp entrance Transceiver unit 13. Loosen the two screws on the junction box, then slide the cover to open the box. Connect the coaxial cable as shown below.
-
Page 20: Processor Unit
2. WIRING Processor Unit Ship’s power TTYCSLA, antenna, control (DPYC-6, local supply) unit and RW-4864 cables (For clamping positions, see the sticker on the reverse side of the top cover.) RGB cable (option) (to external monitor) LAN cable Ground terminal (to other radar or HUB switch) (IV-8sq., local supply) DVI-D and USB cable... - Page 21 2. WIRING How to connect cables inside the processor unit Connect cables from the antenna unit and optional equipment are connected to the FRP_TB board (03P9548), inside the processor unit. Open the cover of the processor unit to find the board. J604: KEYBOARD J617:...
- Page 22 2. WIRING How to fabricate cables connected to the FRP_TB board (03P9548) Signal cable RW-0013 (Fold back outer shield over the vinyl sheath.) Vinyl sheath Pull out wires from the inner shield. Inner shield Vinyl tape Wind the inner shield around the outer shield. Connect to WAGO connector.
-
Page 23: Adjustments
ADJUSTMENTS At the first power application after installation, open the protected menus to adjust the radar. Follow the procedures in this section, in the order shown, to complete the ad- justment. Power lamp Touch pad Setting knob PUSH TO SELECT BRILL MENU RANGE... -
Page 24: How To Set Alarms
3. ADJUSTMENTS How to Set Alarms For alarm details, see section 1.28.2 “Alarm description” in the Operator’s Manual for details. Alarm sound level 1. Press the MENU key to show the main menu. 2. Use the touch pad to select [13 INITIALIZE], then press the left button (click) to show the [INITIALIAZE] menu. -
Page 25: How To Adjust Sweep Timing
3. ADJUSTMENTS 3. Click [CONNING - PORT], then input the distance from the port line to the conning position. L1: Ship length Conning position W1: Width of hull L2: Conning position (from bow) W2: Conning position (from port) Reference point Select the antenna position (refer to section 3.9) or CCRP (Consistent Common Ref- erence Point) as the radar reference point. -
Page 26: How To Adjust Video Level
3. ADJUSTMENTS 4. Click [7 TIMING ADJ] and [AUTO] to activate the automatic adjustment, which takes approx. two minutes. 5. After the adjustment is completed, set the radar to the minimum range. Confirm that no echoes are “missing” at the center of the radar screen. If echoes are missing, click [9 TIMING ADJ OFFSET] and use the setting knob to adjust the timing manually. -
Page 27: How To Suppress Main Bang
3. ADJUSTMENTS Target Correct bearing Displayed relative to position heading Antenna mounting error toward port Image appears deviated clockwise (fast timing of heading switch) (Positive error) Target Displayed Correct position bearing relative to heading Antenna mounting error toward port Image appears deviated clockwise (fast timing of heading switch) (Positive error) 1. -
Page 28: How To Set The Transmission Stop Area
3. ADJUSTMENTS 4. Open the [MAIN]>[CONFIGURATION] menu. 5. Click [INSTALLATION] to show the [INSTALLATION] menu. 6. Click [10 MBS], and enter a suitable value so that the main bang disappears. The setting range is 0 to 255. How to Set the Transmission Stop Area If there is a sector(s) on the radar display in which radar echoes cannot be received because of an obstruction near the antenna, set the sector(s) on the menu. -
Page 29: How To Adjust The Rot/Rudder/Autopilot Graph (Analog Input Only)
3. ADJUSTMENTS 3.11 How to Adjust the ROT/Rudder/Autopilot Graph (Analog Input Only) The ROT (Rate of Turn), Rudder and Autopilot graphs, which appear at the top of the display, can be adjusted on the INITIALIZE menu. Autopilot graph ±300 º/min RUDDER ±180 º... - Page 30 3. ADJUSTMENTS This page is intentionally left blank.
-
Page 31: Appendix 1 Jis Cable Guide
EX: TTYCYSLA - 4 MPYC - 4 TTYCSLA-4 Designation type Designation type # of cores # of twisted pairs The following reference table lists gives the measurements of JIS cables commonly used with Furuno products: Cable Core Core Cable Diameter Type... -
Page 32: Appendix 2 Initialize Menu Tree
APPENDIX 2 INITIALIZE MENU TREE [INITIALIZE] menu Default setting: Bold Italic [INITIALIZE] ALARM SOUND LEVEL (OFF, LOW, MID, HIGH) ALARM menu SYSTEM ERROR (OFF, ON) SENSOR ERROR (OFF, ON) AIS ALARM (OFF, ON) OTHER WARNING (OFF, ON) GRAPH (ON, OFF) OFFSET ADJUST GAIN ADJUST (-300.0 to 300.0, 0.0) RUDDER... - Page 41 2/Nov/2017 H.MAKI...
- Page 44 The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : JAN 2018 Printed in Japan All rights reserved. B : DEC . 12, 2018 Pub. No. IME-36700-B (TEHI ) FR-1908V-BB...