1. Manuals
  2. Brands
  3. Innovate Motorsports Manuals
  4. Automobile Accessories
  5. SCG-1
  6. User manual

Innovate Motorsports SCG-1 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
The Oxygen Sensor used in this device gets very hot in operation.
Do not touch a hot sensor. Do not let a hot sensor touch a combustible surface. Do not use the
sensor with or near flammable liquids or gases. Failure to heed these warnings may result in
severe burns, explosions, fires, or other dangerous events.
 
1.
SCG-1 ...................................................................................................... 2
 
1.1
Changing the SCG-1's gauge face and/or bezel ............................. 3
 
2
Installation ................................................................................................ 4
 
2.1
Wiring ............................................................................................... 4
 
2.1.1
 
2.2
Gauge Mounting and Routing ......................................................... 5
 
2.3
Solenoid Installation ........................................................................ 6
 
2.3.1
Internal Wastegate ...................................................................... 6
 
2.3.2
External Wastegate ..................................................................... 7
 
2.4
MAP sensor ..................................................................................... 7
 
2.5
Wideband Oxygen Sensor Setup .................................................... 7
 
2.5.1
Oxygen Sensor Placement .......................................................... 7
 
2.5.2
Sensor Calibration ....................................................................... 9
 
2.5.3
Calibration Schedule ................................................................. 10
 
3
Boost Controller Setup ........................................................................... 10
 
3.1
Entering Setup Configuration ........................................................ 10
 
3.1.1
 
3.1.2
 
3.2
Display Settings (Gauge Abbreviations) ........................................ 11
 
3.3
RPM Settings (Gauge Abbreviations) ........................................... 11
 
3.4
Solenoid Settings (Gauge Abbreviations) ..................................... 11
 
4
Logworks 3 & LM Programmer Software Package ................................ 13
 
4.1
Download and Install the Logworks 3 Software ............................ 13
 
4.2
LM Programmer ............................................................................. 13
 
4.2.1
Programming Analog Output ..................................................... 14
 
4.2.2
Advanced Analog Output Programming .................................... 14
 
4.2.3
Updating the Firmware .............................................................. 15
 
4.2.4
Changing Sensor Type .............................................................. 15
 
4.3
Logging data from your SCG-1 with LogWorks ............................. 16
Appendix A: Limited Warranty ....................................................................... 17
SCG-1
User Manual
Warning!
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
11-0138C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCG-1 and is the answer not in the manual?

Questions and answers

Related Manuals for Innovate Motorsports SCG-1

Summary of Contents for Innovate Motorsports SCG-1

  • Page 1: Table Of Contents

    Updating the Firmware .............. 15     4.2.4 Changing Sensor Type .............. 15     Logging data from your SCG-1 with LogWorks ......16   Appendix A: Limited Warranty ............... 17   Appendix B: SCG-1 Error Codes and Troubleshooting Tips ......18 11-0138C...

  • Page 2: Scg-1

    A/F and pressure in both the primary and secondary channel viewports. 2. Status or Error display The upper right hand viewport of the SCG-1 is reserved to display the status of the wastegate duty or any error codes that might be present.

  • Page 3: Changing The Scg-1'S Gauge Face And/Or Bezel

    Illuminates when the trigger shift RPM is reached. Changing the SCG-1’s gauge face and/or bezel 1. Lay the SCG-1 face down and remove the three #2 phillips screws from the outside rim of the back plate. 3. Configure the gauge as desired by changing the gauge face and/or bezel.

  • Page 4: Installation

    (-) post. If other Innovate Motorsports devices are going to be daisy-chained along with the SCG-1, it is recommended that all devices be connected to a single ground point, ideally the battery ground (-) post.

  • Page 5: Single Innovate Device Relay Wiring Instructions

    Single Innovate Device Relay Wiring Instructions Gauge Mounting and Routing The SCG-1 gauge fits in any standard 2 1/16” (52mm) gauge pod. Mounting of the gauge should be done in such a manner that the cables are not being forcefully pulled and strained from the gauge itself. Route the sensor and...

  • Page 6: Solenoid Installation

    components that could damage the cable. Also avoid routing the cables near ignition components or other sources of RF (radio frequency) and EMI (Electromagnetic interference) noise. Solenoid Installation Mount the solenoid in a suitable location away from high temperatures or near ignition components. Secure hoses with cable ties.

  • Page 7: External Wastegate

    2.3.2 External Wastegate MAP sensor 1. The MAP sensor MUST be installed with the hose fitting facing down. It is very important that the sensor be isolated from heat sources, mounted away from all ignition and/or other potential RF emitting sources, and protected against excessive vibration. The MAP sensor has two 1/8”...
  • Page 8  When installed in the exhaust, the oxygen sensor must be connected to a powered, functional SCG-1 (no error codes) whenever the engine is running. An un-powered sensor will be damaged in a short period of time when exposed to exhaust gas.

  • Page 9: Sensor Calibration

    3. Power up the SCG-1. The SCG-1 will start warming up the sensor, this is indicated on top right- hand corner viewport of the display by showing “O2 HTR.” After 30-60 seconds, the display will switch from “O2 HTR” and quickly flash “O2 CAL”, indicating that the sensor is being calibrated.

  • Page 10: Calibration Schedule

    - Calibrate once per race weekend Boost Controller Setup Entering Setup Configuration The SCG-1 can be configured directly from the gauge itself or by connecting it to a computer with the LM Programmer software. 3.1.1 Configuration using SCG-1’s interface buttons 1.

  • Page 11: Display Settings (Gauge Abbreviations)

    Windows task bar. Once you have completed your desired changes, press the Program button on the lower right on the software application. You will know that the SCG-1 has been programmed successfully when the Program button grays out. Display Settings (Gauge Abbreviations) 1.
  • Page 12 Duty%) + Duty%). For example, if your Wastegate Duty is set at 30% and your Gain is 50% the SCG-1 will gain up to an additional 15% (Max Duty with Gain =45%). Gain is triggered 1.5 seconds into active boost and will ramp up until Max Duty is gained.

  • Page 13: Logworks 3 & Lm Programmer Software Package

    Press and HOLD both the left and right interface buttons, this will disable/enable solenoid control. If there are no other error codes on the status viewport of the screen, the SCG-1 will display “SC OFF”. In LM Programmer, use the Boost Control ON checkbox to turn the solenoid control ON/OFF.

  • Page 14: Programming Analog Output

    Windows task bar. 4.2.1 Programming Analog Output Connect the SCG-1 to the computer and launch LM Programmer. Select the Analog Output tab. The analog output configuration screen shows voltage versus Lambda for the analog output. The graph display is automatically scaled to the selected voltages values.

  • Page 15: Updating The Firmware

    5. The software will now prompt you to confirm that you wish to overwrite the firmware currently on your SCG-1. 6. Click OK, the gauge of the SCG-1 will go blank. DO NOT power off or disconnect the SCG-1 from the computer until the firmware progress screen completely disappears.

  • Page 16: Logging Data From Your Scg-1 With Logworks

    Logging data from your SCG-1 with LogWorks Logworks is an invaluable tool to help setup your SCG-1. The SCG-1 has four channels of sensor data built in for the tuning of not only your desired boost levels, but also a safe operating air fuel ratio for your engine. These channels are: 1.

  • Page 17: Appendix A: Limited Warranty

    Appendix A: Limited Warranty LIMITED WARRANTY Innovate stands behind the quality of its products. Innovate makes the following warranty to purchasers of its products: All new Innovate products carry a one year warranty from the date of purchase. If proof of purchase cannot be provided, warranty will be determined by date of manufacture.

  • Page 18: Appendix B: Scg-1 Error Codes And Troubleshooting Tips

    3 amp draw. In an O2 error state, all solenoid functions are automatically disabled. To continue using the solenoid functions without the safety cuts, the wideband function of the SCG-1 may be disabled from the setup menu.

Table of Contents