Advertisement
3.2.2 Assembly/Dissambly of cabinet parts and electrical parts
Disassembly procedure
STEP
Fig.
PART NAME
No.
No.
[1]
B.COVER ASSY
3-2-1
[2]
WINDOW(IR)
3-2-2
[3]
TOP COVER ASSY
3-2-3
[4]
HDD COVER ASSY
3-2-4
[5]
HDD
3-2-5
[6]
HDD CASE
3-2-6
[7]
REAR COVER ASSY
[8]
ZOOM UNIT
3-2-7
[9]
REAR BOARD ASSY
[10]
UPPER ASSY
3-2-8
[11]
FRONT ASSY
3-2-9
[12]
MIC
3-2-10
[13]
MAIN BOARD ASSY
3-2-11
[14]
OP BLOCK ASSY
3-2-12
[15]
ORNAMENT(TOP)
3-2-13
3-2-14-1
[16]
OPE BOARD ASSY
/3-2-14-2
[17]
SPEAKER
[18]
MONITOR ASSY
3-2-15
POINT
NOTE
NOTE1
3(S1),2(L1a), 3(L1b)
GRIP BELT,
NOTE2a,b
S2,2(L2a),3(L2b),L2c
3(S3),JACK COVER(AV),
NOTE3
S3,3(L3a),3(L3b),3(L3c)
2(S4), L4a,b
-
CN5
NOTE5a,b,c,d,e,f
5(S6),L6a,b
-
CN7a,b,3(S7),L7a,3(L7b)
NOTE7
2(S8), L8
NOTE8
L9a,2(L9b)
NOTE9
CN10, 2(S10), L10a,b
NOTE10a,b
CN11,S11, L11a,b
NOTE11a,b
S12, L12a, L12b, PLATE(MIC)
NOTE12
CN13a,b, 2(S13)
NOTE13
3(S14)
NOTE14a,b
2(S15), L15a, 3(L15b)
NOTE15a,b
CN16a,b, S16, 2(L16a),
NOTE16a,b
2(L16b), 3(S16)
S17, L17a,b, 2(L17c), BKT(SPK)
NOTE17
S18a, L18a, 2(S18b), 2(L18b)
NOTE18
NOTE1:
When removing the BOTTOM COVER ASSY, open and pull
up the COVER (SD).
NOTE2a:
Pull out the GRIP BELT from the hook and leave it released
before removing the HDD COVER ASSY.
NOTE2b:
During the procedure, be careful not to damage the parts.
NOTE3:
When attaching, be careful not to pinch the parts.
NOTE5a:
During the procedure, be careful in handling the parts.
Pay special attention not to give any external shock to the
HDD.
NOTE5b:
When the HDD is replaced, be sure to refer to Replacing
HDD in "SECTION2 SPECIFIC SERVICE INSTRUCTIONS"
for the procedure after HDD replacement.
NOTE5c:
Be careful as the RUBBER SPACERS on both sides are
easily come off when the HDD is removed from the main
unit.
NOTE5d:
When connecting the FPC to the connector, insert the FPC
straight into the connector. When locking the connector, be
careful not to give so much load that it bends the board.
NOTE5e:
In this procedure, the FPC connected to the HDD connector
is not removed.
If the FPC is removed due to broken wire, be careful in at-
tachment direction.
Pay attention as wrong attachment could damage the HDD.
NOTE5f:
Be careful with the wiring.
NOTE7:
When removing the REAR COVER ASSY, remove the
ZOOM UNIT together with the REAR BOARD ASSY.
NOTE8:
When attaching, first adjust the AV jack position, and then
carefully adjust the DC jack position.
NOTE9:
During the procedure, be careful not to touch or damage the
battery terminal.
NOTE10a:
When removing, release the connector lock, and then pull
out the FPC together with the UPPER ASSY.
NOTE10b:
Please refer to Fig.3-2-13 and the following procedure for re-
moving the UPPER ASSY.
NOTE11a:
When attaching, be careful in handling the JACK COVER
(USB) ASSY.
NOTE11b:
When attaching, be careful with the wiring (MIC).
NOTE12:
When attaching, be careful with the wiring (MIC).
(No.YF266<Rev.001>)1-7
Advertisement
