1. Manuals
  2. Brands
  3. XAVi Manuals
  4. Wireless Access Point
  5. EG102
  6. User manual

XAVi EG102 User Manual

Ethernet iad with voip wireless lan and ethernet switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
EG102
Ethernet IAD with VoIP
Wireless LAN
and Ethernet Switch
Issue 1.0
th
18
July. 2008
I

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EG102 and is the answer not in the manual?

Questions and answers

Summary of Contents for XAVi EG102

  • Page 1 User Manual EG102 Ethernet IAD with VoIP Wireless LAN and Ethernet Switch Issue 1.0 July. 2008...
  • Page 2 XAVi Technologies Corporation. XAVi Technologies Corporation provides this documentation without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular...

  • Page 3: Table Of Contents

    EG102 User’s Guide Introduction....................1 Features ..........................1 Device Requirements ......................2 Getting to know the device................ 3 Parts Check...........................3 Front Panel..........................4 Rear Panel ..........................5 Connecting your device................6 Connecting the Hardware.....................6 Step 1. Connect the WAN port to the broadband device like DSL modem, cable modem or fiber modem ............................
  • Page 4 EG102 User’s Guide DMZ ............................. 25 Security ..........................26 IP Address Filter .......................... 26 Parental Control ........................29 Quality of Service........................30 QoS Classification ........................30 Routing ..........................32 Default Gateway .......................... 32 Static Route ..........................33 Policy Routing..........................33 RIP ............................... 34 DNS.............................35 DNS Server..........................
  • Page 5 EG102 User’s Guide Pickup and put old on hold ......................56 Switch between 2 active calls...................... 56 Timeout ............................57 Three Parties Conference ....................57 Call Transfer........................57 Enquiry service........................57 Call Back Busy Subscriber (Busy) ..................58 Call Back last number called (Call Return) ................58 Diagnostic....................
  • Page 6 EG102 User’s Guide Appendix E - Warranties ..................84 Appendix F - Regulation..................86 Appendix G - Contact information ..............89...

  • Page 7: Introduction

    VoIP interfaces to enjoy data, voice, and video services immediately through high speed connection. This User Guide will show you how to connect your EG102 Ethernet IAD and how to customize its configuration to get the most out of your new product.

  • Page 8: Device Requirements

    EG102 User’s Guide Device Requirements In order to use the EG102, you must have the following: High speed broadband service Instructions from your ISP on what type of Internet access you will be using, and the IP addresses needed to set up access One or more computers, each containing an Ethernet card (10Base-T/100Base-T network interface card (NIC)).

  • Page 9: Getting To Know The Device

    Getting to know the device Parts Check In addition to this document, your package should arrive containing the following: The device (EG102) Ethernet cable Standard phone line cable Power adapter One of EG102 devices RJ-45 Cable RJ-11 Cable Power adapter Figure 1: Package Contents...

  • Page 10: Front Panel

    EG102 User’s Guide Front Panel The front panel of this device will be described here which cover all front panel definitions of other models. Figure 2: Front Panel and LEDs Connector and LED definitions from left to right: Label Color...

  • Page 11: Rear Panel

    EG102 User’s Guide Rear Panel The rear panel of this device will be described here which cover all rear panel definitions of other models. Figure 3: Rear Panel Connections Connector definition: Label Function Antenna Connects to the 802.11b/11g enabled wireless devices in LAN...

  • Page 12: Connecting Your Device

    EG102 User’s Guide Connecting your device This chapter provides basic instructions for connecting the device to a computer or LAN and to the Internet. In addition to configuring the device, you need to configure the Internet properties of your computer(s). For more details, see the following sections in Appendix A:...

  • Page 13: Step 1. Connect The Wan Port To The Broadband Device Like Dsl Modem, Cable Modem Or Fiber Modem

    EG102 User’s Guide Step 1. Connect the WAN port to the broadband device like DSL modem, cable modem or fiber modem Connect the WAN port to the broadband device like DSL modem, cable modem or fiber modem which has the high speed internet connection.

  • Page 14: Getting Start With The Web Pages

    EG102 User’s Guide Getting Start with the Web pages The device includes a series of Web pages that provide an interface to the software installed on the device. It enables you to configure the device settings to meet the needs of your network. You can access it through a web browser on a PC connected to the device.
  • Page 15 EG102 User’s Guide Advanced Setup: provides information about the current configuration of various system features with options to change the configuration. It includes the sub menus WAN, LAN, NAT, Security, Parental Control, Quality of Service, Routing, DNS, Print Server and Port Mapping.

  • Page 16: Commonly Used Buttons

    EG102 User’s Guide Diagnostic: provides the diagnostic utility to check the LAN and Wireless physical connection and WAN connection as well. Management: provides the administration utilities. It includes the sub menus, Settings, System Log, TR-069 Client, Internet Time, Access Control, Update Software, and Save/Reboot.

  • Page 17: Testing Your Setup

    EG102 User’s Guide Testing your Setup Once you have connected your hardware and configured your PCs, any computer on your LAN should be able to use the device to access the Internet. To test the connection, turn on the device, wait seconds till device booting up and then...
  • Page 18 EG102 User’s Guide Option Default Setting Explanation/Instructions User/Password admin/admin User name and password to access the device LAN Port Assigned static IP This is the IP address of the LAN port IP Address address: on the device. The LAN port connects 192.168.1.1...

  • Page 19: Device Information

    EG102 User’s Guide Device Information The Device Information web page menu includes the following submenus: Summary Statistics Route DHCP. Summary The Summary Page of the device shows the following information, Board ID, Software version, Bootloader version, Wireless driver version, LAN IP, Default gateway, Primary DNS server and Secondary DNS server.

  • Page 20: Statistic

    EG102 User’s Guide Statistic The Statistic Page of the device shows the following information of LAN and WAN ports, Interfaces, data transmitting (Received and Transmitted directions) in that interface such as total bytes, packets, error count and drop count. Figure 8: Device LAN Port Statistic Information...

  • Page 21: Arp

    EG102 User’s Guide The ARP Page of the device shows the ARP table mapping the IP address and related MAC address. The ARP table contains IP address, Flag, MAC address, Device Interface. Figure 11: Device ARP Table Information DHCP The DHCP Page of the device shows the DHCP table which DHCP server of device assigns the IP address to the PC requesting an IP address.

  • Page 22: Advanced Setup

    EG102 User’s Guide Advanced Setup The Advance Setup menu includes the sub menus WAN, LAN, NAT, Security, Parental Control, Quality of Service, Routing, DNS, Print Control, and Port Mapping. Security Parental Control QoS (Quality of Service) Routing Print Server Port Mapping You can configure your internet connection from this page.
  • Page 23 EG102 User’s Guide Figure 14: WAN Port Configuration To configure VLAN tag on the WAN interface: Check the “VLAN Mux – Enable Multiple Protocols Over WAN with 802.1Q VLAN Tag” Enter the unique VLAN ID Enter the Mark of 802.1p from 0 to 7...

  • Page 24: Bridging

    EG102 User’s Guide Bridging Figure 16: WAN Connection, Bridging Configuration To configure the Bridging settings: Check “Enable Bridge Service” to enable bridge service Enter the service name for this bridging interface. Click Next Figure 17: WAN Setup Summary The WAN Setup Summary page shows all of parameters. Click Save if correct and...

  • Page 25: Ppp Over Ethernet (Pppoe)

    EG102 User’s Guide PPP over Ethernet (PPPoE) Figure 18: WAN Connection, PPPoE Configuration To configure the PPPoE settings: Enter the User’s PPP Username and Password Enter the Service Provider Name if any Select the Authentication Method used during negotiation, default is AUTO.

  • Page 26: Ip Over Ethernet

    EG102 User’s Guide Figure 19: IGMP Multicast and WAN Service Configuration Global Settings: Check to Enable IGMP Multicast Check to Enable WAN Service Enter the Service Name Click Next The WAN Setup Summary page as previous WAN Setup Summary figure shows all of parameters.
  • Page 27 EG102 User’s Guide To configure the IP over Ethernet settings: Select “Obtain an IP address automatically” or “User the following (fixed) IP address” and then also enter the WAN IP address and WAN Subnet Mask. Select “Obtain default gateway automatically” or “User the following gateway”...

  • Page 28: Lan

    EG102 User’s Guide Figure 22: LAN Configuration To configure LAN: Enter the IP address which the CPE in the LAN will use to connect to the device. For example, enter 192.168.1.1 Enter the Subnet Mask. For example, enter 255.255.255.0 Check to enable UPnP if necessary Check to Enable IGMP Snooping.

  • Page 29: Nat (Network Access Translation)

    EG102 User’s Guide Besides the dynamic assignment of IP address, you can configure the static IP address too which will be reserved for the device with specified MAC address only. Click Add Entries to enter MAC address of the device and fixed IP address.

  • Page 30: Port Triggering

    EG102 User’s Guide Global Setting Select a service from the predefined list or enter the name of Custom Server Enter the Server IP Address located in the LAN to provide the service to remote party Enter the Start External Port # and End External Port # that open to remote to...

  • Page 31: Dmz

    EG102 User’s Guide Click Save/Apply Figure 26: Add A Rule Of Port Triggering A DMZ (DeMilitarized Zone) host is a computer on your network that can be accessed from the Internet. The de-militarised zone (DMZ) is for forwarding IP packets from the remote parties that are not fixed to any of the applications configured in the virtual server.

  • Page 32: Security

    EG102 User’s Guide Click Save/Apply Security The Security feature provides two more setting pages including IP filtering in Routed mode and Parental Control. IP Address Filter The device can block the packet in outgoing and incoming directions. By default, all outgoing IP packets from LAN is allowed to surf Internet, but some IP packets can be blocked by setting up filters.
  • Page 33 EG102 User’s Guide Figure 29: Add - Outgoing IP Filter Setup Global Setting Enter the Filter Name Select the Protocol from the selection list. Enter the Source IP Address and Subnet Mask (range of IP addresses) of packet Enter the one port or multi ports (port range)
  • Page 34 EG102 User’s Guide Click Add to add a rule of Incoming IP Filtering. Check Remove and click Remove to remove the specified entry. Figure 31: Add - Incoming IP Filter Setup Global Setting Enter the Filter Name Select the Protocol from the selection list.

  • Page 35: Parental Control

    EG102 User’s Guide Parental Control This feature allows you to configure some of PCs in LAN to surf Internet in specific time period. Figure 32: Parental Control Configuration Click Add to add a rule of schedule for parental control. Check Remove and click Remove to remove the specified entry.

  • Page 36: Quality Of Service

    EG102 User’s Guide Quality of Service The Quality of Service feature provides a method to prioritize the packet and arrange a better efficiency of bandwidth. In other words, some traffic such as voice or video has handled as higher priority than others such as data to get near real time response.
  • Page 37 EG102 User’s Guide Check Remove and click Remove to remove the specified entry. Figure 36: Quality of Service Configuration The screen creates a traffic class rule to classify the upstream traffic, assign queue priority which defines the precedence and type of service. A rule consists of a class name and at least one condition below.

  • Page 38: Routing

    EG102 User’s Guide Select the Physical LAN Port from the list which packets through this port will be classified. Select the Protocol from the list which packets with this protocol will be classified. Select the Differentiated Service Code Point (DSCP) Mark Check from the list.

  • Page 39: Static Route

    EG102 User’s Guide Static Route You could create your own routing entry by the destination network address and interface to configure the data traffic in the network. Click Add to add entry. Figure 38: Static Route Configuration Global Setting Enter the Destination Network Address and Subnet Mask (range) Check Use Gateway IP Address and enter the IP address where packet will be forwarded to.

  • Page 40: Rip

    EG102 User’s Guide Enter the Policy Name of this configuration Select the physical LAN interface (port) from the list Enter the Source IP Address Select the Use Interface from the list Enter the Gateway IP Address where packet will be forwarded to.

  • Page 41: Dns

    EG102 User’s Guide The DNS feature provides two more setting pages including DNS server setting and Dynamic DNS. DNS Server Figure 41: DNS Configuration Global Setting Check Enable Automatic Assigned DNS checkbox, this router will accept the first received DNS assignment from one of the PPPoE or Static IP/DHCP interface. If the checkbox is not checked, enter the IP addresses of the static primary DNS server and secondary DNS server.

  • Page 42: Print Server

    EG102 User’s Guide Click Add to add Dynamic DNS setting. Check Remove and click Remove to remove the specified entry. Figure 43: Add a Dynamic DNS Global Setting Select the Dynamic DNS service provider from the list Enter the your Hostname...

  • Page 43: Port Mapping

    EG102 User’s Guide Global Setting Check Enable On-Board Print Server checkbox Enter the Printer Name which you like others to see it while searching network printer. Enter the maker and model name.. Click Save to save the configuration Port Mapping The page provides Port Mapping configuration.
  • Page 44 EG102 User’s Guide Figure 46: Port VLAN Configuration Global Setting Enter the Group Name Select the value of VLAN ID Select the available LAN ports from available LAN interfaces into grouped interface. The selected LAN interface will be removed from its original group and joined this new group.

  • Page 45: Wireless Setup

    EG102 User’s Guide Wireless Setup The Wireless Setup web page menu comprises: Basic Security MAC Filter Wireless Bridge Advanced Quality of Service Station Information Basic The device provides wireless connection to wireless clients. This page allows you to enable the wireless service, hide the network from active scan and set the SSID (Service Set IDentifier).

  • Page 46: Security

    EG102 User’s Guide Check to enable Wireless feature Check to enable Hide Access Point to hide from active scan of wireless client Check to enable Clients Isolation that wireless clients can not share information to each other. Check to disable WMM Advertise where WMM stands for WiFi Multimedia. This technology maintains the priority of audio, video and voice applications in a Wi-Fi network so that other applications and traffic are handled in lower priority.
  • Page 47 EG102 User’s Guide If the Network Authentication is Shared. Select the Encryption Strength with 64bits or 128bits, select the current Key Index and enter the key and four keys when necessary as the same as Network Authentication is Open and WEP Encryption is enabled.
  • Page 48 EG102 User’s Guide If the Network Authentication is WPA, enter WPA Group Rekey Interval, the IP address and Port number of Radius server, Radius Key, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is enabled, select the Encryption Strength with 64bits or 128bits, select the current Key Index and enter the key and four keys when necessary.
  • Page 49 EG102 User’s Guide If the Network Authentication is WPA2-PSK (pre-shared key), enter the WPA Pre-Shared Key and enter WPA Group Rekey Interval, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable WEP encryption. If WEP Encryption is enabled, select the Encryption Strength with 64bits or 128bits, select the current Key Index and enter the key and four keys when necessary.

  • Page 50: Mac Filter

    EG102 User’s Guide MAC Filter Figure 49: Wireless Setting – Input MAC Address Figure 50: Wireless Setting – Define the action plan for those MAC address Global Setting Select the MAC Restrict Mode from one of Disable (no MAC filter), Allow (only those PCs with MAC addresses in the table can surf Internet) and Deny (only those PCs with MAC addresses in the table can not surf Internet).

  • Page 51: Wireless Bridge

    EG102 User’s Guide Wireless Bridge The wireless bridge feature is also known as WDS, Wireless Distribution System). Figure 51: Wireless Bridge Configuration Global Setting Set the AP mode as Access Point or Wireless Bridge When the AP mode is set to Wireless Bridge, the Wireless Bridge Restrict...

  • Page 52: Advanced

    EG102 User’s Guide Advanced This page allows you to configure advanced parameters for wireless communication. Figure 52: Wireless Setting – Advanced Global Setting Enable AP Isolation if you do not want AP to be able to communicate with each other.

  • Page 53: Station Information

    EG102 User’s Guide Set the Maximum Associated Wireless Client Set XPress Technology enabled or disabled. Set 54g Mode to 54g Auto, 54g Performance, 802.11b, 54g LRS (limited rate support). Set 54g Protection to AUTO if there are 802.11g and 802.11b coexisting in the wireless network.

  • Page 54: Voice Setup

    EG102 User’s Guide Voice Setup The Voice Setup web page menu comprises: Interface Setup Provisioning Setup SIP Setup Line 1 Setup Line 2 Setup RTP/Codec Setup Operational Setup Interface Setup This page allows you to specify the voice packets to pass through the specific interface and to choose different country code to set voice related parameters including ringing type, ringing frequency, tone type, tone frequency, cadence, etc..

  • Page 55: Provisioning Setup

    EG102 User’s Guide Provisioning Setup This page allows you to setup the provisioning server if ISP uses this method to provide customer’s configuration profile. The device will use TFTP protocol to get the configuration information from the server. Figure 55: Voice Configuration – Provisioning Setup...

  • Page 56: Line 1 Or Line 2 Setting

    EG102 User’s Guide Global Setting: Select the SIP Transport Protocol: UDP or TCP. Enter the Listen Port number which is a port number of UDP or TCP. Enter the Maximum Redirect number which is the number that VoIP may allow to redirect or forward to.

  • Page 57: Rtp/Codec Setup

    EG102 User’s Guide Global Setting: Select to Enable this line or not Enter UID (User Name) for Line 1 or Line 2 Enter the Password Enter the Display Name which will be shown in the called party when you call out.
  • Page 58 EG102 User’s Guide Figure 58: Voice Configuration – RTP/Codec Setup Global Setting: Enter the TOS byte. The TOS stands for Type of Service. It is defined in the RFC1394 and used in RTP packet. Enter the RTP Packet Period of milliseconds. Suggest leave it as default for better quality.

  • Page 59: Operational Setup

    EG102 User’s Guide Operational Setup This page allows you to configure the call features including call forward, call waiting, three-way conference and so on as well as tones, FXS and caller ID. Figure 59: Voice Configuration – Operational Setup 1...
  • Page 60 EG102 User’s Guide Figure 60: Voice Configuration – Operational Setup 2 Global Setting: Place a check in the list of call features which is supported in Line 1 and Line 2. Enter the value of feature timers including Redialing Duration, Retrial Interval, OnHook Delay, PSTN Session Progress Timeout, Call Waiting Ring Timeout.

  • Page 61: Voice Supplementary Service

    EG102 User’s Guide Voice Supplementary Service Call Forward There are three types of call forward, call forward unconditional, call forward no response and call forward on busy. You could activate and deactivate these features by press keypad in the phone.

  • Page 62: Static Configuration

    EG102 User’s Guide Static Configuration Secret Number is usually an extra service and customers are charged an additional monthly fee. It must be possible to provision from remote if CLIR is enabled or disabled for each outgoing phone call. On per call basis Caller Line Identification Restriction (CLIR) enables a calling party to prevent presentation, on a call by call basis, of his number to the called party.

  • Page 63: Timeout

    EG102 User’s Guide Timeout The customer receives a call when in a conversation, and chooses to ignore the call waiting notification, the calling party will receive a busy signal after 24 seconds. Three Parties Conference Three party conference can be invoked from Call waiting or Enquiry services. When the subscriber has two active calls, one on hold and one in conversation state, it shall be possible to connect all three into a three parties conference.

  • Page 64: Call Back Busy Subscriber (Busy)

    EG102 User’s Guide Call Back Busy Subscriber (Busy) Call Back Busy Subscriber (CCBS) enables a calling customer (A), encountering a busy destination (B), to have the retry dialing automatically until destination becomes idle, without having to make a new call attempt.

  • Page 65: Diagnostic

    EG102 User’s Guide Diagnostic Diagnostic This page allows you to diagnostic the connections of LAN, Wireless and WAN ports. Figure 61: Diagnostic Click Test to run the test script and get the diagnostic result.

  • Page 66: Management

    EG102 User’s Guide Management The Management web page menu comprises: Settings System Log TR-069 Client Internet Time Access Control Update Software Save/Reboot Settings This page allows you to backup the current configuration of the device, update the configuration, and restore default configuration (factory setting).

  • Page 67: System Log

    EG102 User’s Guide Figure 64: Restore Default Settings To click Restore Default Settings to restore the factory default settings. System Log This page allows you to view system log and also configure system log that way you want to see.

  • Page 68: Tr-069 Client

    EG102 User’s Guide Global Setting Select to Enable Log function or not Select Log Level from the list Select Display Level from the list Select Mode from the list Click Save/Apply to save the configuration. TR-069 Client This page allows you to access TR-069 ACS (Auto-Configuration Server). The ACS can provision, configure, and diagnostic the device from remote site.

  • Page 69: Internet Time

    EG102 User’s Guide Internet Time This page allows you to sync up the real time clock from Internet. . Figure 68: Internet Time Configuration Global Setting Check to Automatically synchronize with Internet time servers Click Save to save your settings Access Control This submenu provides you local (LAN) or remote (WAN) access to the device.

  • Page 70: Ip Address

    EG102 User’s Guide Global Setting: Specify the method by which you wish to access the router locally or remotely by selecting it. The following are the methods available for local and remote access: HTTP ICMP (Ping) TELNET TFTP Click Save/Apply to save the configuration.
  • Page 71 EG102 User’s Guide view configuration settigns and statistics, as well as updaet the device software. Figure 72: Management Configuration – Access Control: Password Global Setting: Select the level of Username (admin, support, or user). The user name “admin” has the unrestricted access to change the view configuration of the device. The user name “support”...

  • Page 72: Update Software

    EG102 User’s Guide Update Software This page allows you to upgrade the software (firmware). Figure 73: Management Configuration – Update Software Global Setting: First of all, you have to get the updated software (firmware) from ISP or manufacture. Click Browser to specify the location and filename Click Update Software to start the process.

  • Page 73: Appendix A - Configuring The Internet Settings

    EG102 User’s Guide Appendix A - Configuring the Internet Settings This appendix provides instructions for configuring the Internet settings on your computers to work with the device. Configuring Ethernet PCs Before you begin By default, the device automatically assigns the required Internet settings to your PCs.

  • Page 74: Windows Me Pcs

    EG102 User’s Guide displayed with a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled. Skip to step If Internet Protocol (TCP/IP) does not display as an installed component, click Install.

  • Page 75: Windows Nt 4.0 Workstations

    EG102 User’s Guide In the Windows task bar, click the Start button, point to Settings, and then click Control Panel. Double-click the Network icon. The Network dialog box displays with a list of currently installed network components. If the list includes TCP/IP, and then the protocol has already been enabled.

  • Page 76: Assigning Static Internet Information To Your Pcs

    EG102 User’s Guide Click OK twice to confirm and save your changes, and then close the Control Panel. Assigning static Internet information to your PCs If you are a typical user, you will not need to assign static Internet information to your LAN PCs because your ISP automatically assigns this information for you.

  • Page 77: Configuring Wireless Pcs

    EG102 User’s Guide Configuring Wireless PCs You need to configure the operating system installed on your Wireless PCs using the same procedure described for Configuring Ethernet PCs section. Positioning the wireless PCs The wireless network cards used determine the maximum distance between your wireless PCs and your device.

  • Page 78: Appendix B - Troubleshooting

    EG102 User’s Guide Appendix B - Troubleshooting This appendix suggests solutions for problems you may encounter in installing or using the device, and provides instructions for using several IP utilities to diagnose problems. Contact Customer Support if these suggestions do not resolve the problem.

  • Page 79: Diagnosing Problem Using Ip Utilities

    EG102 User’s Guide Problem Troubleshooting Suggestion I forgot/lost my user ID or If you have not changed the password from the password. default, try using “admin” as both the user ID and password. Otherwise, you can reset the device to the default configuration by pressing three times the Reset Default button on the front panel of the device.

  • Page 80: Nslookup

    EG102 User’s Guide You can also test whether access to the Internet is working by typing an external address, such as that for www.yahoo.com (216.115.108.243). If you do not know the IP address of a particular Internet location, you can use the nslookup command, as explained in the following section.

  • Page 81: Appendix C - Glossary

    EG102 User’s Guide Appendix C – Glossary Term Description 802.11 A family of specifications for wireless LANs developed by a working group of the IEEE. This wireless Ethernet protocol, often called Wi-Fi. 10BASE-T A designation for the type of wiring used by Ethernet networks with a data rate of 10 Mbps.
  • Page 82 EG102 User’s Guide types of data. See routing. Broadband A telecommunications technology that can send different types of data over the same medium. DSL is a broadband technology. Broadcast To send data to all computers on a network. DHCP Dynamic Host Configuration Protocol DHCP automates address assignment and management.
  • Page 83 EG102 User’s Guide File Transfer Protocol A program used to transfer files between computers connected to the Internet. Common uses include uploading new or updated files to a web server, and downloading files from a web server. Gbps Abbreviation of Gigabits per second, or one billion bits per second.
  • Page 84 EG102 User’s Guide Light Emitting Diode An electronic light-emitting device. The indicator lights on the front of the device are LEDs. MAC address Media Access Control address The permanent hardware address of a device, assigned by its manufacturer. MAC addresses are expressed as six pairs of hex characters, with each pair separated by colons.
  • Page 85 EG102 User’s Guide PPPoA Point-to-Point Protocol over ATM One of the two types of PPP interfaces you can define for a Virtual Circuit (VC), the other type being PPPoE. You can define only one PPPoA interface per VC. PPPoE Point-to-Point Protocol over Ethernet One of the two types of PPP interfaces you can define for a Virtual Circuit (VC), the other type being PPPoA.
  • Page 86 EG102 User’s Guide TFTP Trivial File Transfer Protocol A protocol for file transfers, TFTP is easier to use than File Transfer Protocol (FTP) but not as capable or secure. TKIP Temporal Key Integrity Protocol (TKIP) provides WPA with a data encryption function. It ensures that a unique...
  • Page 87 EG102 User’s Guide Wide Area Network Any network spread over a large geographical area, such as a country or continent. With respect to the device, WAN refers to the Internet. Web browser A software program that uses Hyper-Text Transfer Protocol (HTTP) to download information from (and...

  • Page 88: Appendix D - Specification

    EG102 User’s Guide Appendix D - Specification A1. Hardware Specifications LAN Interface • Four port 10/100BaseT Ethernet Switch (4 * RJ-45 connectors), IEEE 802.3u with MDI/MDIX auto-detection • Integrated 802.11b/g WLAN Access Point WAN Ethernet Line Interface • 10/100BaseT Ethernet port Analog Voice Interface •...
  • Page 89 EG102 User’s Guide Support NAT and DMZ Virtual server (port mapping) and IP filters Protection against IP and MAC address spoofing UPnP NAT traversal and VPN / IPSec pass-through Voice Support voice CODECs like G.711, G.726, G.729A/B, BV16, ILBC, T.38 etc...
  • Page 90 Appendix E - Warranties B1. Product Warranty XAVi Technologies warrants that the xDSL unit will be free from defects in material and workmanship for a period of twelve (12) months from the date of shipment. XAVi Technologies shall incur no liability under this warranty if －...
  • Page 91 2. The customer must return the defective product to XAVi Technologies within fourteen (14) days after the request for replacement. If the defective product is not returned within this time period, XAVi Technologies will bill the customer for the product at list price.
  • Page 92 But if it does, the user will be required to correct the interference at his or her own expense. The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless XAVi expressly approves the changes or modifications.
  • Page 93 EG102 User’s Guide FCC Part 68 Notice This equipment complies with Part 68 of FCC Rules. On the base unit of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. IF REQUESTED, THIS INFORMATION MUST BE GIVEN TO THE TELEPHONE COMPANY.
  • Page 94 EG102 User’s Guide UL Safety Regulations Disconnect TNV circuit connector or before removing cover or equivalent. Disconnect TNV circuit connector(s) before disconnecting power. Do not use this product near water for example, near a bathtub, washbowl, and kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
  • Page 95 You can help us serve you better by sending us your comments and feedback. Listed below are the addresses, telephone and fax numbers of our offices. You can also visit us on the World Wide Web at www.xavi.com.tw for more information. We look forward to hearing from you!

Table of Contents