Subscribe to Our Youtube Channel
Summary of Contents for Bushranger MC-E-2
- Page 1 Edger Attachment MC-E-2 Cultivator Attachment MC-T-2 Owner’s/ Operator’s Manual Completely read and understand this manual before using this product.
-
Page 2: Table Of Contents
It is essential that any operator of this Multi-cutter reads and understands the contents this manual before using the Multi-cutter. For additional assistance, contact any local authorized BUSHRANGER dealer. Important Notice The benefits to the consumer given by this warranty are in addition to other rights and remedies of the con- sumer under a law in relation to the goods or services to which this warranty relates. -
Page 3: Safety Instructions
5. Inspect the tool attachment and replace any parts that are cracked, chipped or damaged before using the Multi-Cutter. 6. Never use a tool attachment or replacement parts that are not approved by BUSHRANGER. 7. Maintain the Multi-Cutter according to the recommended maintenance intervals and procedures in the Maintenance section beginning on page 11. -
Page 4: Fuel Safety
9. Keep a firm footing and balance. Do not overreach. 10. Use the right tool for the job. Do not use the Multi-Cutter for any job that is not recommended by BUSHRANGER. ＿ 3 ＿... -
Page 5: Safety And Instruction Decals
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any that are damaged or lost. MC-E-2 (Edger Attachment) ON SHAFT (Part No.221501) ON SHAFT (Part No.221502) ON DEBRIS SHIELD (Part No.221528) -
Page 6: Product Description
Product Description MC-E-2 (Edger Attachment) 1. Gearcase 2. Debris Shield 3. Shaft Assembly 4. Edger Blade 5. Wheel MC-T-2 (Cultivator Attachment) 1. Gearcase 2. Debris Shield 3. Shaft Assembly 4. Cultivator Tines ＿ 5 ＿... -
Page 7: Assembly
Assembly MC-E-2 (Edger Attachment) Installing Guard WARNING POTENTIAL HAZARD Guard ・ Foreign objects can be thrown by Edger. Guard Stud Lock Washer WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. Plate HOW TO AVOID THE HAZARD Flat Washer ・... -
Page 8: Mc-T-2 (Cultivator Attachment)
MC-T-2 (Cultivator Attachment) Installing Shaft and Gearcase Driveshaft Attach the shaft assembly to the gearcase assembly. NOTE: Carefully inspect both side of the shaft assembly. The arrow marking side of the shaft Locating Hole assembly positions to the power unit. The no marking side of the shaft assembly connects Locating Screw Arrow Mark... -
Page 9: Idle Speed Adjustment
Keep hands and body away from the cutting attachment. If idle speed adjustment is necessary, and after adjustment the cutting attachment rotates or the engine stalls, stop using the Multi-cutter immediately! Contact your local authorized BUSHRANGER Dealer for assistance and servicing. ＿ 8 ＿... -
Page 10: Operation
Operation MC-E-2 (Edger Attachment) WARNING POTENTIAL HAZARD ・ Foreign objects can be thrown by Edger Attachment. WHAT CAN HAPPEN ・ Contact with thrown objects can cause personal injury. HOW TO AVOID THE HAZARD ・ Never operate the Edger Attachment without the blade guard in place. -
Page 11: Mc-T-2 (Cultivator Attachment)
Setting Depth of Cut Guard IMPORTANT: Set the depth of cut before you start the engine. Increase the 1. Loosen the knob holding the guard to the plate. Decrease the Depth of Cut Depth of Cut 2. Rotate the guard as necessary to set the depth of cut. Note that: ・... -
Page 12: Maintenance
Maintenance MC-E-2 (Edger Attachment) Flexible Drive Shaft Maintenance Interval The Edger Attachment uses a flexible drive shaft inside the drive shaft tube. The flexible drive shaft should be lubricated after each 30 hours of use. Gearcase Flexible Drive Shaft Lubrication Flexible Drive Shaft 1. -
Page 13: General Cleaning And Tightening
・ Always turn off your Multi-Cutter before you clean or perform any maintenance on it. The BUSHRANGER Multi-Cutter will provide maximum performance for many, many hours if it is main- tained properly. Good maintenance includes regular checking of all fasteners for correct tightness, and cleaning the entire machine. -
Page 14: Specifications
Specifications MT262 with MC-E-2 MC-T-2 Weight (Kg) ※ 1 ※ 2 Engine Displacement (cm 25.4 Fuel Tank Capacity (L) Carburetor Diaphragm Type Ignition System Solid State Spark Plug NGK BPMR8Y Spark plug Gap (mm) 0.6-0.7 Fuel Mixture Two-stroke Oil Mix 50:1 Ratio... - Page 16 11 Sodium Street, Narangba Qld 4504 P/N.241976-00 GB 1905 IN...
Need help?
Do you have a question about the MC-E-2 and is the answer not in the manual?
Questions and answers