Subscribe to Our Youtube Channel
Summary of Contents for Andover Controls InfiLink 200
- Page 1 Controlling Tomorrow’s World InfiLink 200 Installation Guide Electronic Version Andover Controls Corporation Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
- Page 2 IMPORTANT NOTICE This product is subject to change without notice. This document does not con- stitute any warranty, express or implied. Andover Controls Corporation re- serves the right to alter capabilities, performance, and presentation of this product at any time.
- Page 3 Preface The InfiLink 200 Installation Guide presents instructions for installing the InfiLink 200 on the Infinet, a network of local controllers. It first presents how to prepare the site, including facts about proper ground- ing, then how to install the InfiLink 200.
- Page 4 InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
-
Page 5: Warranty Registration
Installing the InfiLink 200 on Infinet This manual covers installing the InfiLink 200 on Infinet. For information on how to plan and set up your network, refer to the EnergyNet and Infinet Configuration Guide. Warranty Registration Your warranty is effective for 18 months starting on the date the system is shipped. - Page 6 InfiLink 200 Dimensions Each InfiLink 200 is 8.5 × 7.5 × 2.75 in. The unit is inside a hinged aluminum enclosure that meets UL standards. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com...
-
Page 7: Power Requirements
The InfiLink 200 should receive power from its own independent, unswitched circuit. InfiLink 200 requires 120 V +10/–15%, 60 Hz. You can select 230 VAC, 50 Hz for European sites by setting two jumpers, but for smoke control applications, you must use 120 VAC +10/–15%, 60 Hz. - Page 8 We cannot guarantee that the control system will operate as documented unless you properly ground all controllers. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
- Page 9 Surges of much lower potential also impact the reliability of Andover Controls equipment. Since properly grounded Andover Controls units respond to changes in potential more rapidly than poorly grounded electrical systems, a poor- ly grounded building tries to reach ground through the Andover Controls system.
-
Page 10: Environmental Requirements
• Is connected to a corroded or galvanized pipe. • Is connected using a small gauge wire (smaller than 14 AWG). 2. Be sure your InfiLink 200 is connected to the ground with a copper conductor that terminates at the distribution panel. -
Page 11: Parts Required
Figure 1 shows the location of the eyelets and corner screw holes. 3. Screw the InfiLink 200 to a wall or secure it firmly on a base using standard No. 8 screws in the screw holes in the lower corners of the enclosure. - Page 12 .19 Is .50 in. .80 in. from bottom edge RS-232 Connector Top of Enclosure 2.75 in. Deep The pinouts for the RS-232 connector are listed in the appendix. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
-
Page 13: Connecting The Ac Power
The AC power connection is in the lower left corner of the InfiLink 200. You must wire the AC cable to the three screws on the far left. - Page 14 Figure 2 shows the location of the AC power connection. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
- Page 15 Figure 2. The Inside of the InfiLink 200 RS-232 1 / 8A BAUD RATE SHLD 19200 9600 2400 SHLD 1200 SHLD SHLD POWER SHLD (INPUT) I N F I L I N K 2 0 0 F1 3A 250V SLOW BLOW...
- Page 16 Figure 3. Metal Plate and Screw for Power Supply Wire Metal Plate Insert Wire Here 5. Place the black wire under the metal plate behind the top screw, labeled HOT. 6. Tighten the screw with a flathead screw driver. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
- Page 17 Wiring the Infinet to the 9000 Controller You connect the first piece of Infinet cabling from the 9000 controller to the InfiLink 200. Port 1, labeled INPUT, is where the connection to the 9000 controller, 9500, or previous InfiLink 200 comes in to the link.
-
Page 18: Setting The Baud Rate
Setting the Baud Rate You set the baud rate using the rotary switch to the upper right on the front of InfiLink 200. The baud rate should match the rate of the rest of the network. We recommend 19.2K baud. - Page 19 Contact your telephone company to install the line. To connect the modem to the InfiLink 200, connect the RS-232 cable on the modem to the RS-232 port on the top center of the link.
- Page 20 Powering Up the InfiLink 200 Connect the AC power cable to an electrical power source and the InfiLink 200 starts automatically. The following occurs: 1. The red power light to the right and vertical center of the InfiLink 200 comes on.
- Page 21 Appendix RS-232 Port Pinouts Table A-1 shows the pinouts for the RS-232 port on the InfiLink 200. InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
- Page 22 InfiLink Installation Table A-1. Pinouts for RS-232 Port on InfiLink 200 Pin Number Purpose Chassis Driving High –V Driving High InfiLink 200 Installation Guide Technical Manuals Online! - http://www.tech-man.com firealarmresources.com...
Need help?
Do you have a question about the InfiLink 200 and is the answer not in the manual?
Questions and answers