Gigabyte GS-SR101 System Installation Manual
  1. Manuals
  2. Brands
  3. Gigabyte Manuals
  4. Server
  5. GS-SR101
  6. System installation manual
Gigabyte GS-SR101 System Installation Manual

Gigabyte GS-SR101 System Installation Manual

1u rack mount server
Hide thumbs Also See for GS-SR101:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
System Installation Guide
GS-SR101
1U Rack Mount Server
SYSTEM INSTALLATION GUIDE
1-i

Advertisement

Table of Contents
loading

Related Manuals for Gigabyte GS-SR101

Summary of Contents for Gigabyte GS-SR101

  • Page 1 System Installation Guide GS-SR101 1U Rack Mount Server SYSTEM INSTALLATION GUIDE...
  • Page 2 1. INTRODUCTION 1.1. P REFACE 1.2. F EATURES 2. HARDWARE INVENTORY 3. SYSTEM INSTALLATION 3.1. C HASSIS OVER EMOVAL 3.2. P ROCESSOR NSTALLATION 3.3. F EATSINK NSTALLATION 3.4. S RAM I YSTEM NSTALLATION 3.5. I NSTALLING ANDLE 3.6. R EINSTALL OVER 3.7.

  • Page 3: Introduction

    1. INTRODUCTION 1.1. Preface Using this manual will help you get the most from your Rack Mount Server. Keeping the manual with your Rack Mount Server to refer when you want information and help. In order to get the optimal usage out of your Rack Mount Server and you should Remember the following: Read through all the instruction for your Rack Mount Server .
  • Page 4 VCM SDRAM Supports up to 4.0GB SDRAM Supports only 3.3V SDRAM DIMM Storage Controller Max 4 IDE ATA channels (2 x ATA-66 and 2 x ATA-100 for IDE RAID 0 or 1) Support front-accessible 2 hot-swap drives featuring IDE ATA-100...
  • Page 5 Power Total output power 250 W Input : Rating switch full range 90V~250V 47~63 Hz Operating Temperature 5 to 40 degree C Thermal Solution Special-designed Heat-sink and hi-efficiency chassis fans for dual 1 GHz plus processor thermal solution Other Features Support Wake On LAN ( WOL ) Support External Modem Ring On Optional DOC solution for embedded Internet/Networking Applications...

  • Page 6: Hardware Inventory

    2. Hardware Inventory When you unpack your GS-SR100 Rack Mount Server ,Check that all the items that you ordered are present in good condition. Review the inventory checklist below to be sure that the components and optional components that you ordered are included. If anything is missed or damaged , contact your retailer as soon as possible .

  • Page 7: System Installation

    System Installation Guide 3. System Installation Note: Please remove the protection plastic cover from top side first. If not, the system heat could not spread from top side . 3.1. Chassis Cover Removal Use screwdriver to remove the two screws on the chassis top cover .( Fig 1 ) And then slide the top cover out of the system .( Fig 2 ) Fig-1 Fig-2...

  • Page 8: Fan+Heatsink

    3.2. Processor Installation To install Socket 370 CPU ,lifts up bar located next to the Socket .And then insert Socket 370 CPU inside Socket ,and push the lever bar back into original position . ( Fig-3 & Fig-4 ) CPU-1 CPU-2 Fig-3 3.3.
  • Page 9 System Installation Guide For CPU1 ,Fan power cable connect to J13 ( CPU1 FAN) connector and for CPU2 , Fan power cable connect to J15 ( CPU2 Fan ) Connector .Note to make sure the connector is plugged into the header in the correct and click well. ( Fig-7 ) J13-CPU1 Fan Connector J15-CPU2 Fan Connector Fig-7...

  • Page 10: Reinstall Top

    3.5. Installing Handle Get Handle and screw from the accessories box. And then mount the handle on the front panel .( Fig-9 & Fig-10 ) Fig-9 3.6. Reinstall Top Cover After the above steps ( 3.1 to 3.5 ) were finished then slide a top cover to a chassis (Fig-11 )and use screwdriver to reinstall the 2 screws on the top cover .( Fig-12 ) Fig-11...

  • Page 11: Hard Disk Drive Installation

    System Installation Guide 3.7. Hard Disk Drive Installation Get the quick-swap Hard Disk tray from the accessories box. And then connect the HDD data cable and Power cable to Hard Disk Drive. Note IDE data cable Red Line is make sure to connect Hard Disk Drive pin 1 . ( Fig-13 & Fig-14 ) HDD Power Cable HDD Data Cable Pin 1 Fig-13...
  • Page 12 System Installation Guide When you put HDD tray into the chassis ,make sure that the lever is at a 90 degree angle to the chassis .( Fig-17 ) Otherwise ,damage may occur to lever. After that push HDD tray to chassis carefully and make sure the HDD tray is click into Chassis .
  • Page 13 Fig-20 When you put HDD tray into the chassis ,make sure there is a no gap between HDD tray and chassis .Otherwise the system can’t detect the HDD .(Fig-21 ) Fig-21 System Installation Guide HDD Tray Click...

  • Page 14: Led I Ndicators

    System Installation Guide 3.8. Front Side IDE ATA-100 Hot-swap HDD Slim Type CD-ROM Slim Type FDD 3.9. LED Indicators LAN2 LED Power Switch & LED LAN1 LED HDD1 LED HDD2 LED Fan LED...
  • Page 15 Indicator Description: Power LED: Green System Power On LED Off System Power Off LAN LED: Green 100M LAN Active LED Off 0M LAN Active (But when Data Access the LED is Blinking) Blinking Data Access Fan LED: LED Off System Fan status Normal Orange System Fan Cras h HDD LED:...

  • Page 16: C Onnector

    System Installation Guide 3.11. Connector Icons Suggested icons Description Keyboard Mouse Parallel Port Serial Port 3-10...

Table of Contents