Hide thumbs Also See for DL210:

Advertisement

Quick Links

1. Product and Accessories ...........................................................2
1.1 Parts List.........................................................................2
1.2 Parts Identification...............................................................3
2. Installation............................................................................5
2.1 Preparation before Installation................................................5
2.2 Drill Holes........................................................................6
2.3 Adjust Latch's Backset..........................................................6
2.4 Adjust Deadbolt's Backset......................................................7
3 Install Latch, Deadbolt and Strikes ................................................9
3.1 Install Latch and Deadbolt .....................................................9
3.2 Install Strikes and Lining Boxes.............................................10
4 Install the Lock Units...............................................................11
4.1 Adjust Torque Bar Length......................................................11
4.3 Mounting of Outside Section onto door.....................................12
4.5 Install Inside Section of Lock ................................................14
4.6 Check and Adjust after Installation .........................................15
5 Problems or Feedback .............................................................16
Shepherd 210A Installation Manual V1.1

Table of Contents

2
©
©Copyright 2004. Hongda USA Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DL210 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hongda USA DL210

  • Page 1: Table Of Contents

    4.4 Mounting the Plat to Fix Outside Section onto Door ………………...13 4.5 Install Inside Section of Lock ………………………………………...14 4.6 Check and Adjust after Installation …………………………………..15 5 Problems or Feedback …………………………………………………….16 Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 2: Product And Accessories

    Inside unit Outside unit Pinch screws Deadbolt Deadbolt strike Deadbolt strike lining box Latch Latch strike Latch strike lining box Square axis for latch Wood screw Emergency keys Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 3: Parts Identification

    1.2 Parts Identification 1. Decoration plate 14. LED display 2. Sliding dust cover 15. Inside unlocking button 3. Green LED indicator 16. Inside locking button Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 4 21. Inside unit body 9. Outside unit body 22. Deadbolt keyhole 10. Deadbolt 23. Latch emergency keyhole 11.Latch 24. Deadbolt emergency release hole 12.Outside lever 25. Pinch screw hole 13.Function keys Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 5: Installation

    Kwikset standard for 2 lock hole doors. If your door has only one hole or no holes in the door, follow the instructions below. (Note: Most hardware stores have 2-1/8” and 1” hole cutters that fit standard hand drills.) Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 6: Drill Holes

    2.3 Adjust Latch’s Backset The left of adjustment hole Regulator pin The backset is at the 2 3/8” position, when the product is shipped from the factory. Screw-post hole Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 7: Adjust Deadbolt's Backset

    Pull The right edge of adjust hole backset been adjusted to 2 3/4” position. Screw-post hole Make sure the regulator pin is at the correct angle as shown. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 8 2 3/4” screw hole coincides with driving board hole. Pull Figure shows the backset is in 2 3/4” (70 mm) position. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 9: Install Latch, Deadbolt And Strikes

    UP mark of the edge. deadbolt should point up). Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 10: Install Strikes And Lining Boxes

    Draw strike plate line and screw holes Cut 1/16” notches for the strike Install strikes, tighten the screws. plates. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 11: Install The Lock Units

    Door Outer Door Surface Fig 2 Fig 3 4.2 Remove Plate and Screws from Inside Section Remove the battery cover on Inside Section of lock. And remove Plate from Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 12: Mounting Of Outside Section Onto Door

    1. Put rubber gasket on the Outside Section of lock, with the smooth side away from lock. (Ignore shape of cutout holes; it doesn’t matter.) (Fig 6, 7) Fig 6 Fig 7 Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 13: Mounting The Plat To Fix Outside Section Onto Door

    (slightly shorter of the four long pinch screws supplied) for mounting through the two holes near the top of the lock. Screw in tightly making sure rubber gasket is positioned evenly around lock. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 14: Install Inside Section Of Lock

    (Fig. 12) 6. Fasten the two long C Screws on the lower portion of the unit. (Fig. 13) Note: Don’t fasten screws too tight before final checkup. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.
  • Page 15: Check And Adjust After Installation

    Congratulations! You are done with the installation! Tip: If the deadbolt does not moves smoothly, loosen pinch screws a little and adjust the lock body position until the deadbolt moves smoothly. Shepherd 210A Installation Manual V1.1 © ©Copyright 2004. Hongda USA Inc.

Table of Contents