Advertisement
1.3.5. DO regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power
connections to ensure that none are loose.
1.3.6. DO check that the voltage marked on the product is the same as the electrical power supply to be used, and check that all fused
plugs are fitted with the correct capacity fuse.
1.3.7. DO NOT pull or carry the powered appliance by its power supply lead. Products
must not be pulled or carried by their output cables.
1.3.8. DO NOT pull power plugs from sockets by the power cable.
1.3.9. DO NOT use worn or damage leads, plugs or connections. Immediately
or have repaired by qualified persons. A U.K. 3 pin plug with ASTA/BS approval
is fitted. In case of damage, cut off and fit a new plug according to the following
instructions (UK only - see diagram right).
a) Ensure the unit is correctly earthed via a three-pin plug.
b) Connect the Green/Yellow earth wire to the earth terminal ‘E’.
c) Connect the Brown live wire to live terminal ‘L’.
d) Connect the Blue neutral wire to the neutral terminal ‘N’.
1.4.
BATTERY CHARGER SAFETY INSTRUCTIONS.
F WARNING! DO NOT attempt to charge any battery other than that supplied for the drill. Other types of batteries may explode!
All mains electrical supply safety features must be followed as described in 1.3. above.
!
Disconnect the charger from the mains power supply when not in use.
!
DO NOT expose the charger to damp or wet conditions.
%
DO NOT pull or carry the charger by the power lead.
%
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take charger to an authorised agent.
%
DO NOT dismantle the charger as this may cause damage or personal injury and will invalidate your warranty.
%
DO NOT use and extension lead between the mains and the battery charger.
%
DO NOT insert foreign objects or material into the hole reserved for the battery.
%
DO NOT recharge a second battery immediately after charging a battery. Consecutive charging will overheat the charger. Allow the unit
%
to cool for 15 minutes before charging the next battery.
DO NOT attempt to connect two chargers together.
%
Store the charger in the same manner as battery in 1.2.
!
2.
SPECIFICATIONS
Model: CP9812VHK
Chuck size . . . . . . . . . . . . .10mm
Motor . . . . . . . . . . . . . . . . .12V
No load speed . . . . . . . . . .0-550RPM
Max torque hard wood . . . .120kg/cm
Full charge time . . . . . . . . .1 hour
1.
Keyless chuck
2.
Electronic variable speed switch
3.
Lock, reverse and forward switch
4.
12V Battery power pack
5.
4 step torque control & 1 hammer
6.
Battery release button (one each side)
Battery charger (not illustrated)
3. OPERATING INSTRUCTIONS
Note:
When new, the battery will have been shipped in a low charge mode. It will take longer to charge the battery initially, and several
subsequent charges may also take a little longer than when the battery reaches its optimum performance.
3.1.
CHARGING THE BATTERY PACK.
3.1.1. To remove the battery pack from the drill, depress the two side release clips (fig 1 item 6).
FWARNING! Do not touch the metal terminals.
3.1.2. Place drill carefully back into its carrying case and remove the battery charger.
3.1.3. Insert the mains power lead into the power socket in the side of the battery charger, and stand
on a safe flat surface, DO NOT connect to the mains at this point.
3.1.4. The battery and charger have the positive + and negative - terminals marked. Align the correct
terminals and insert the battery (fig 2). Note: the battery is designed so that it will only enter the
charger unit the correct way. When placed in the charger, a very slight downward pressure will
seat the battery firmly into the power terminals (if you are not able to do this you may be trying
to insert the battery the wrong way around. Remove the battery, turn it around, and try again).
3.1.5. When securely in place, plug into mains power and switch on. The red power light will glow
indicating that the charge cycle has started.
3.1.6. The red indicator (battery charger) light will remain on until the unit has been fully charged.
When complete the red light will go out and the green light will go on. Under normal conditions the battery will take
up to 1 hour to fully charge.
3.1.7. When the red light has gone out, unplug the charger from the mains power and remove the battery ready for use with the drill.
3.1.8. Place the charger and mains lead safely back into the carry case. Insert the battery into the drill ready for use.
Note: If you try to charge a battery that has been removed from a recently used drill the red charge light may not come on. In such
a case allow the battery to cool for a time and try again.
Model: CP9818VHK
Chuck size . . . . . . . . . . . . .13mm
Motor . . . . . . . . . . . . . . . . .18V
No load speed . . . . . . . . . .0-650RPM
Max torque hard wood . . . .170kg/cm
Full charge time . . . . . . . . .1 hour
1.
Keyless chuck
2.
Electronic variable speed switch
3.
Lock, reverse and forward switch
4.
18V Battery power pack
5.
4 step torque control & 1 hammer
6.
Battery release button (one each side)
Battery charger (not illustrated)
Yellow & Green
Earth wire
replace
Blue
Neutral
wire
fig 1
fig 2
Brown Live
wire
3
amp
3 pin
plug
CP9812VHK & CP9818VHK - 0064 (2) - 200899
J
J
J
Advertisement
