Summary of Contents for LG SIGNATURE OLED65G6P
- Page 1 OLED TV OLED65G6P OLED77G6P OLED65G6P (M10 x L70) (M4 x L10) OLED77G6P X 18 (M8 X L77) (M4 X L12) (M8 X L25) CR2032 www.lg.com P/No: MFL69383610 (1606-REV02)
- Page 3 OLED65G6P...
- Page 4 OLED77G6P...
- Page 8 ENGLISH OLED65G6P OLED77G6P MODELS (OLED65G6P-U) (OLED77G6P-U) 1,461 x 883 x 243 (mm) 1,734 x 1,055 x 317 (mm) Stand type 57.5 x 34.7 x 9.5 (inches) 68.2 x 41.5 x 12.4 (inches) Dimensions (W x H x D) 1,461 x 892 x 68 (mm)
- Page 9 Safety and Reference Please read this manual carefully before operating your set and retain it for future reference. OLED65G6P OLED77G6P www.lg.com *MFL69383631* P/NO : MFL69383631 (1606-REV02)
-
Page 10: Important Safety Instructions
Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Always comply with the following precautions Follow all instructions. to avoid dangerous situations and ensure peak performance of your product. • Do not use this apparatus near water. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN... - Page 11 • Use only with the cart, stand, tripod, bracket, or • CAUTION concerning the Power Cord table specified by the manufacturer, or sold with (Can differ by country): the apparatus. When a cart is used, use caution Check the specification page of this owner’s when moving the cart/apparatus combination to manual to be certain concerning current avoid injury from tip-over.
- Page 12 • Grounding • Cleaning (Except for devices which are not grounded.) When cleaning, unplug the power cord and wipe Ensure that you connect the earth ground wire gently with a soft cloth to prevent scratching. Do to prevent possible electric shock (i.e., a TV not spray water or other liquids directly on the with a three-prong grounded AC plug must TV as electric shock may occur.
-
Page 13: Viewing 3D Imaging (For 3D Models)
Viewing 3D Imaging • Do not dispose of batteries in a fire. • Do not short circuit, disassemble, or allow the (For 3D models) batteries to overheat. • Do not use high voltage electrical equipment near the TV, (e.g., a bug zapper). CAUTION This may result in product malfunction. -
Page 14: Optional Extras
Preparing CAUTION • Do not use any unapproved items to ensure the safety and product’s lifespan. NOTE • Any damages or injuries by using unapproved • When the TV is turned on for the first time after items are not covered by the warranty. being shipped from the factory, initialization of •... -
Page 15: Lifting And Moving The Tv
Lifting and Moving the TV CAUTION • Avoid touching the screen at all times, as this When moving or lifting the TV, read the following may result in damage to the screen. to prevent the TV from being scratched or •... -
Page 16: Using The Button
Using the Button Mounting on a Table You can simply operate the TV functions, pressing 1 Lift and tilt the TV into its upright position on a or moving the button. table. - Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. -
Page 17: Mounting On A Wall
LG brand wall mount. The LG wall (For OLED65G6P) mount is easy to adjust or to connect the cables. When you do not use LG’s wall mount bracket,... -
Page 18: Connections (Notifications)
Connections (Notifications) Connecting to an Antenna or Cable Connect an antenna, cable, or cable box to watch You can connect various external devices to the TV. TV. The illustrations may differ from the actual Supported external devices are: HD receivers, DVD items and an RF cable is optional. -
Page 19: Battery Installation
Slim Remote Control (Depending upon model) Returns to the previous screen. The descriptions in this manual are based on * Clears all on-screen displays and returns to the buttons on the remote control. Please read TV viewing. this manual carefully and use the TV correctly. (Home) Accesses the Home menu. -
Page 20: Magic Remote Functions
Magic Remote Functions (Depending upon model) (POWER) Turns the TV on or off. Magic remote battery is low. When the message You can turn your set-top box on or off Change the battery. is displayed, replace the by adding the set-top box to the universal remote battery. -
Page 21: Open Source Software Notice Information
How to Deregister the Magic Remote Press the (Home) buttons at the same time, for five seconds, to unpair the (Navigation buttons) Press the up, down, Magic Remote with your TV. left or right button to scroll the menu. • Pressing and holding the button will (up/down/left/right) If you press... -
Page 22: Troubleshooting
Troubleshooting Environment Condition • Operating Temperature • Cannot control the TV with the remote control. 0 °C to 40 °C (32 °F to 104 °F) - Check if anything such as tape has been placed • Operating Humidity over the receiver. Less than 80 % - Check if there is any obstacle between the •... -
Page 23: Fcc Notice
Regulatory FCC RF Radiation Exposure Statement [For having wireless function (WLAN, Bluetooth,...)] This equipment complies with FCC radiation exposure limits set forth for an uncontrolled FCC Notice environment. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter. -
Page 24: Note To Cable/Tv Installer
WARNING! WARNING (For Canada) Never place a television set in an unstable [For product having the wireless function using 5 location. A television set may fall, causing serious GHz frequency bands] personal injury or death. Many injuries, particularly to children, can be avoided by taking simple 1 The device for operation in the band 5150–5250 precautions such as: MHz is only for indoor use to reduce the... -
Page 27: Child Safety
CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations. -
Page 28: Register Your Product Online
Declaration of Conformity Trade Name Model OLED65G6P-U, OLED77G6P-U Responsible LG Electronics Inc. Party Address 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A 201 - 266 - 2534 LG Customer Information Center The model and serial numbers of the TV are located on the For inquires or comments, visit www.lg.com or call;... -
Page 29: Network Settings
webOS TV Quick Setup Guide * Image shown may differ from your TV. * Image shown on a PC or mobile phone may vary depending upon the Operating System (OS). * Depending upon the version of the software, icon position can be changed. Network Settings Press the (Home) button to access the... -
Page 30: Troubleshooting Network Problems
Troubleshooting Network Problems Depending upon the version of the software, icon position can be changed. Press the (Home) button to access the Check the AP (Router) or consult your Internet Smarthome menu. Select (Settings) and press service provider. Wheel (OK). When X appears next to Gateway: Unplug the power cord of the AP (Router) or cable modem, wait 10 seconds. -
Page 31: Updating The Tv Firmware
SmartShare PC SW Installation & Setting Install the SmartShare PC SW program on your PC. www.lg.com Go to . Then, select your region. Select SUPPORT. Select Software & Firmware. Then, search for your model. Then, select SmartShare PC SW. Download the SmartShare PC SW and install it on your PC. You can run the program when installation is complete. - Page 32 Wi-Fi Direct Setting (Home) (Settings) (All Settings) Network Wi-Fi DIRECT If a local network is not available, you can connect a portable device directly to the TV using Wi-Fi Direct. With SmartShare, you can share files or screens of devices connected to Wi-Fi Direct. WI-FI DIRECT Picture When you open Wi-Fi Direct menu, a list of available devices appears.
- Page 33 Troubleshooting Wi-Fi Network Problems Checkpoints Make sure that you have the latest version of the software. - If you are using a Wi-Fi router, check whether you have the latest firmware installed. - If there are any available updates, update the firmware according to the manufacturer's instructions. - Check the current software version and if there is an available update, install it.
- Page 34 Radio Frequency (RF) Interference and Absorbing Obstructions Interference Interference Interference Type of Barrier Type of Barrier Type of Barrier Potential Potential Potential Wood Water Medium Plaster High Synthetic material Bricks Medium Concrete High Glass Marble Medium Bulletproof glass High Metal Very High...
-
Page 35: External Control Device Setup
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com... -
Page 36: Key Codes
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button... - Page 37 EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL DEVICE SETUP • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series.
- Page 38 EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
-
Page 39: Communication Parameters
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA... -
Page 40: Transmission / Receiving Protocol
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. - Page 41 EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
- Page 42 EXTERNAL CONTROL DEVICE SETUP Data Min : 00 to Max : 64 * (Depending on model) Ack [i][ ][Set ID][ ][OK/NG][Data][x] 14. Bass (Command: k s) 09. Tint (Command: k j) ► To adjust Bass. ► To adjust the screen tint. You can also adjust in the AUDIO menu.
- Page 43 EXTERNAL CONTROL DEVICE SETUP Set ID = All = 00 5th Band 20(decimal) Data 00 & 01 = Channel Data is 10 = 00 0a Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00 * It depends on model, and can adjust when sound mode is EQ adjustable value.
- Page 44 EXTERNAL CONTROL DEVICE SETUP Number Data 05 = Digital Antenna TV = 02 - 22 : Antenna TV (DTV) – Don’t Use Physical Total = ma 00 00 00 11 00 01 02 Channel Number - 26 : Cable TV (CADTV) - Don’t Use Physical 2.
- Page 45 11 11 EXTERNAL CONTROL DEVICE SETUP 24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data X : don’t care 00 : DTV 01 : CADTV 02 : Satellite DTV 10 : ATV Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] ISDB-BS (Japan)
- Page 46 EXTERNAL CONTROL DEVICE SETUP 27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Ack [u][ ][Set ID][ ][OK/NG][Data][x]...