Advertisement
Quick Links
The SGM595 is born from the elegance and prestige that has always distinguished BEINAT S.r.l. and from the home
fitness concept.
The probe is a Catalytic gas detection unit with IP55 protection that, together with one of BEINAT's industrial type
Control Units, detects the presence of esplosive gas such as Methane, LPG, Hydrogen.
The probe is managed by a microprocessor which not only supplies an alarm signal to the control unit connected to
it, but also allows execution of a self-diagnosis and therefore an AUTOMATIC CALIBRATION, in order to always have
the maximum detection accuracy.
The self-calibration means the probe adapts in harsh and variable temperature environments, avoiding false alarms due
to anomalous events.
The probe has a 0 ÷ 20 % LEL linear output conforming to the 4 ÷ 20mA standard, for which can be connected with
one of BEINAT's industrial control units.
The important innovation of this probe is:
The possibility to substitute the sensor at the end of the operating cycle or fault by the technician without having to
send to BEINAT Srl.
Indispensabile instrument for the annual check of the probes
Instrument of testing TS1008
To facilitate the reading of the functional parameters of the probe as well as the control of annual
operating, the BEINAT S.r.l. has built a new portable tester TS1008.
The tester allows to read all the data in the memory of the probes eand by serial transmission,
it prints the ticket that confirms the testing data.
Important: Assembly / maintenance of the appliance must be carried out by qualified personnel and in
accordance with applicable laws and regulations.
The manufacturer assumes no responsibility for the use of products that have to comply with particular
environmental and / or installation standards.
Important note
Before connecting the equipment, it is recommended that you read the instruction manual carefully and
keep it for future reference. It is also recommended to perform the electrical connections correctly as
per enclosed drawings, observing the instructions and the Standards.
N.B. Refer to the documentation in all cases where the symbol is on the side
Installation and user
guide
Conventional Gas Sensor SGM595
Electric connections also available on
Belonging to
V. R1bd04
CONFORMITY
Compliant EN 60079-29-1
Installation EN 60079-29-2
Reports issued by TUV Italia
Channel: Beinat gas solutions
EN 50194
EN 50270
Advertisement
Related Manuals for BEINAT SGM595
Summary of Contents for BEINAT SGM595
- Page 1 Conventional Gas Sensor SGM595 V. R1bd04 The SGM595 is born from the elegance and prestige that has always distinguished BEINAT S.r.l. and from the home fitness concept. The probe is a Catalytic gas detection unit with IP55 protection that, together with one of BEINAT’s industrial type Control Units, detects the presence of esplosive gas such as Methane, LPG, Hydrogen.
-
Page 2: Technical Specifications
When doing the electrical connections, follow the drawing closely. Any use of the detector for purposes other than the intended one is considered improper, and as a result of which BEINAT S.r.l. therefore disclaims any responsibility for possible damages caused to people, animals or objects. -
Page 3: Maintenance
Compatible control units CONTROL UNITS MOUNTING PROBES Max. DEGREE ALARMS POSITIVE OPERATING protec. alarms safety range GS100M unit 1 zone Wall/cabinet IP44 GS300-Mc unit 1 zone Wall/cabinet IP44 BX444-MC unit 1 zone Wall/cabinet IP44 BX150 unit 1 zone Panel IP42 BX180 unit 1 zone Omega bar DIN IP20... - Page 4 FAULT 100% Led ON 100% 1 2 3 4 5 6 SELECTION OF THE OPERATING RANGE SGI595 The SGM595 Conventional Probes, NOT SUITABLE IN ATEX ZONE, LEAVE THE FACTORY WITH A DEFAULT PERATING ANGE VALUE SET AT LEL. 100% To select the operation range to...
- Page 5 2 and terminal 3. Linear Otput 4-20 mA If othe r p rob le ms arise , a sp e cialise d and /or authorise d te chnician and /or the Distrib utor of BEINAT S.r.l. should be contacted directly. Page 5...
- Page 6 L . I . E . Gas imput Test Test SGM595 The installation of the SGM595 probe, its ordinary and extraordinary maintenance, and its out of service removal at the end of the functional life guaranteed by the manufacturer, must be carried out by authorized or specialized personnel.
- Page 7 Cable Gland PG13,5 Opening of the Cover. With the help of a screwdriver to turn counterclockwise for a quarter of turn SGM595 autosetting Closeof the Cover. With the help of a screwdriver to turn counterclockwise for a quarter of turn ...
- Page 8 Stamp and signature of the dealer Purchase date: Serial Number : The Beinat S.r.l. following the targhet to improve its products, reserves the right to modify the technical features, aesthetic and functional any time without prior notice. BEINAT S.r.l. Via Fatebenefratelli 122/C 10077, S. Maurizio C/se (TO) - ITALY Tel.