Makita DUM604ZX Instruction Manual page 12

5. Never work on unstable surfaces.
6. Remove sand, stones, nails etc. found within
the working range. Foreign particles may dam-
age the cutting tool and can cause dangerous
kick-backs.
Should the cutting tool hit stones or other hard
7.
objects, immediately switch off the motor and
inspect the cutting tool.
8. Inspect the cutting tool at short regular inter-
vals for damage (detection of hairline cracks
by means of tapping-noise test).
9. Before commencing cutting, the cutting tool
must have reached full working speed.
10. The cutting tool has to be equipped with the
appropriate guard. Never run the equipment
with damaged guards or without guards in
place!
All protective installations and guards sup-
11.
plied with the equipment must be used during
operation.
12. Always remove the battery cartridge from the
equipment:
whenever leaving the equipment
—
unattended;
— before clearing a blockage;
— before checking, cleaning or working on
the equipment;
— after striking a foreign object;
— whenever the equipment starts vibrating
abnormally.
13. Always ensure that the ventilation openings
are kept clear of debris.
14. Cutting means continues to run after the motor
is switched off.
Cutting Tools
Employ only the correct cutting tool for the job
in hand.
Maintenance instructions
1. The condition of the equipment, in particular of
the cutting tool of the protective devices must
be checked before commencing work.
2. Turn off the motor and remove the battery
cartridge before carrying out maintenance,
replacing cutting tools or cleaning the equip-
ment or cutting tool.
3. When not in use, store the equipment indoors
in dry and high or locked-up place - out of the
reach of children. Clean and maintain before
storage.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Cordless Hedge Trimmer Safety
Warnings
1. Keep all parts of the body away from the cut-
ter blade. Do not remove cut material or hold
material to be cut when blades are moving.
Make sure the switch is off when clearing
jammed material. A moment of inattention while
operating the hedge trimmer may result in serious
personal injury.
2. Carry the hedge trimmer by the handle with
the cutter blade stopped. When transporting or
storing the hedge trimmer always fit the cut-
ting device cover. Proper handling of the hedge
trimmer will reduce possible personal injury from
the cutter blades.
3. Hold the power tool by insulated gripping
surfaces only, because the cutter blade may
contact hidden wiring. Cutter blades contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
4. Do not use the hedge trimmer in the rain or in
wet or very damp conditions. The electric motor
is not waterproof.
5. First-time users should have an experienced
hedge trimmer user show them how to use the
trimmer.
The hedge trimmer must not be used by
6.
children or young persons under 18 years of
age. Young persons over 16 years of age may be
exempted from this restriction if they are undergo-
ing training under the supervision of an expert.
7. Use the hedge trimmer only if you are in good
physical condition. If you are tired, your attention
will be reduced. Be especially careful at the end of
a working day. Perform all work calmly and care-
fully. The user is responsible for all damages to
third parties.
8. Never use the trimmer when under the influ-
ence of alcohol, drugs or medication.
Work gloves of stout leather are part of the
9.
basic equipment of the hedge trimmer and
must always be worn when working with it.
Also wear sturdy shoes with anti-skid soles.
10. Before starting work check to make sure
that the trimmer is in good and safe working
order. Ensure guards are fitted properly. The
hedge trimmer must not be used unless fully
assembled.
Make sure you have a secure footing before
11.
starting operation.
12. Hold the tool firmly when using the tool.
13. Do not operate the tool at no-load
unnecessarily.
14. Immediately switch off the motor and remove
the battery cartridge if the cutter should come
into contact with a fence or other hard object.
Check the cutter for damage, and if damaged
repair immediately.
15. Before checking the cutter, taking care of
faults, or removing material caught in the cut-
ter, always switch off the trimmer and remove
the battery cartridge.
12 ENGLISH