Tranzeo Wireless Technologies TR-49 Quick Start Manual
  1. Manuals
  2. Brands
  3. Tranzeo Wireless Technologies Manuals
  4. Radio
  5. TR-49
  6. Quick start manual

Tranzeo Wireless Technologies TR-49 Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
QUICK START GUIDE FOR THE
TRANZEO WIRELESS TR-49
R
2.0a
EVISION
J
2
, 2006
ANUARY
ND

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TR-49 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Tranzeo Wireless Technologies TR-49

Summary of Contents for Tranzeo Wireless Technologies TR-49

  • Page 1 QUICK START GUIDE FOR THE TRANZEO WIRELESS TR-49 2.0a EVISION , 2006 ANUARY...

  • Page 2: Safety Notices

    FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a Residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication.
  • Page 3 This next-generation wireless LAN device – the TRANZEO TR-49, brings Ethernet-like performance to the wireless realm. The TRANZEO TR-49 also provides powerful features such as the Internet- based configuration utility as well as WEP and WPA security. Maximize network efficiency while minimizing your network investment and maintenance costs.
  • Page 4 Flashing : WPA/TKIP Enabled Off: WPA Off Amber No Function in 4.9 On: ACL Enabled Green Off: ACL Off On: WDS Enabled Green Off: WDS Off Power Supply ONLY use the power adapter supplied with the TR-49. Otherwise, the product may be damaged.
  • Page 5 Before installing, you must determine if the unit will be in the horizontal or vertical orientation. The TR-49 model can be mounted in either orientation. The Ethernet boot should always be placed so that the cable runs toward the ground for maximum environmental protection.
  • Page 6 Connecting the Ethernet Cable Step 1 Place the Ethernet Boot Cover over the end of your Cat 5 cable. Step 2 Attach Ethernet Cable Lock on side of the Ethernet Boot. This is easiest to do before you attach the RJ-45 Jack. Step 3 Tighten using a ¾”...
  • Page 7 Step 4 Repeat steps 2 & 3 to attach the second Ethernet Cable Lock if you purchased the optional dual port boot. Step 5 Place Sealing Gasket over screws. Step 6 Remove gasket backing and place boot cover on radio. This will ensure that you attach the sticky side of the gasket to the underside of the Ethernet Boot.
  • Page 8 Step 8 Place the Ethernet boot over the 4 Screw Posts. Apply 4 Kept nuts to the screw posts and tighten until the gasket makes full contact with the Ethernet boot. The gasket should be at least 50% compressed. Optional dual port boot specific note. If you are not going to be using the second port make sure that it is tightened down to ensure a weather-tight seal.
  • Page 9 Dual Ethernet Ports The TR-49 has two Ethernet port available. Port A is used to connect to the radio in the radio in the case. Port B is used to power and provide Ethernet connectivity to additional devices. This allows...

  • Page 10: Html Interface

    HTML Interface NOTE: The default IP address is 192.168.1.100 The default User Name is admin The default Password is default Passwords When you first enter the Web Interface, you will be required to enter a new recovery password. This password is intended to allow the ISP to change the password of the device if they forget it.

  • Page 11: Wireless Settings

    Wireless Settings SSID The SSID is a unique ID given to an Access Point. Wireless clients associating to the Access Point must have the same SSID. The SSID can have up to 32 characters. Visibility Status Makes the AP visible or invisible to clients. Channel Sets the channel that the AP and clients will use TX Rate...

  • Page 12: Administrative Settings

    The access user name. Password/Confirm Password Enter the password for accessing the device Ext. Info Enabled Enable extended information. Extended information is only displayed with Tranzeo Wireless Technologies Access Points. Signal / Status LEDs Un-select to turn off the LEDs on the unit.
  • Page 13 WDS (Wireless Distribution System) is a modification to the 802.11 spec that allows AP to communicate directly with each other. WDS allows users to spread out coverage to a larger area without the need for a backhaul link. The tradeoff is that overall throughput is greatly affected for all users of the AP’s linked. WDS is not recommended for use with large numbers of clients, or in cases where throughput needs to be maximized.
  • Page 14 ecurity Settings—Basic Enabled Turn On WEP Authentication Select Open or Shared Key Authentication Key Length Level of Encryption. NOTE: 64 bit is referred to as 40 bit on some systems Default Key Choose the default WEP key Activate Keys Enter your WEP keys. NOTE: Keys must be entered in HEX only.

  • Page 15: Access Control

    Access Control Enable Access Control Select this box to enable access control. Associated Wireless Devices Click any devices to disassociate them Wireless Devices Available Click any wireless device that should be associated with the AP Associate With This Station Manually Enter the MAC address of a client and then click “add”...
  • Page 16 Stations List (AP Mode Only) This page displays a list of the stations associated with the AP and their connection statistics. The first column is simply the order in which the stations are stored in the Station Table. The second column is the name field. If the device is a Tranzeo 49, and it has the Extended Info option turned on in the Administrative Settings Window, then the device name will appear here.

  • Page 17: Arp Table

    ARP Table This feature was added as a troubleshooting screen. It shows the devices which have sent either a broadcast or directly tried to communicate with the device. Under normal circumstances, there should be a limited number of entries in this table, especially if you have interstation blocking turned on at the AP.
  • Page 18 Network Configuration – Bridge Mode This page allows you to control the network configuration of the device. You can choose Static or DHCP Client IP configuration for the device. Note: If you select DHCP, and a DHCP server is not pre- sent, the device will try to get an IP for up to 5 minutes.

  • Page 19: Dhcp Server Configuration

    DHCP Server Configuration Subnet Mask Subnet mask for the DHCP pool. Address Range Starting Address The starting address of the DHCP pool. The addresses are sequential starting with the Starting Address. Number of Addresses The number of addresses you want to have in the DHCP pool Select This Unit to use the gate- Gateway way set on the WAN interface of...
  • Page 20 Static Routing Setup Screen Routing is an incredibility complex topic that is way beyond the scope of a QuickStart or Manual. This screen is intended for those users who have a strong understanding of IP Routing. Misconfiguration on this screen could result in serious network problems or even the loss of functionality.
  • Page 21 Menu Options Uplink Speed ( Mbps) Sets the maximum total pipe size for this client. The order and traffic size is determined based on this value. Dynamic Fragmentation Reduce delay for high-priority traffic and adaptive fragmentation where the fragmentation is determined by the uplink speed.

  • Page 22: Port Management

    Cloning MAC This is a new feature. It allows the CPE the clone the MAC of the device behind it. This feature can be useful when dealing wth some PPPoE and Radius Implimentations. When the device is in Cloning MAC mode, it can only be managed from the LAN side of the device.

  • Page 23: Port Filtering

    Port Filtering This is a new feature. It allows the radio to block requests for certain IP’s or ports to and from devices behind the router. For example, if a customer wishes to block access to FTP from this network to the outside world, you would 1.
  • Page 24 Associated Access Point Information about the access point is displayed here. Some items will only be displayed if the Access Point is a Tranzeo TR-49 series AP with the Extended Info turned on in the Administrative Settings Window. Receiving This box displays the current signal and the Lowest and Highest values. For the most accurate readings, data must be transmitted through the unit.
  • Page 25 Statistics The Statistics Screen is divided into 3 main areas, UMAC , LMAC and Ethernet. For Radio Troubleshooting, the UMAC statistics are likely the most useful. The UMAC breaks down the statistics into Good and Bad Packets, whereas LMAC defines why the packets are bad.
  • Page 26 The failed packets should be 1% or less in a normal operating environment. In the TX statistics, there should little to no Retransmits at Series 2, 3 or 4. Life Statistics are reset on each reboot. In the Ethernet Statistics screen, excessive collisions are usually a sign that the radio and the device it is linked to are not on the same Duplex options.
  • Page 27 APPENDIX A: Lightning Information What is a proper Ground? This antenna must be grounded to a proper Earth Ground. According to the National Electrical Code Sections 810-15s and 810-21, the grounding conductor shall be connected to the NEAREST accessible locations of the following: a) The building / structure grounding electrode b) The grounded interior metal water piping system c) The power service accessible means external to enclosure...
  • Page 28 Ungrounded Radio An ungrounded radio causes the surge to pass through the radio. In this case the radio most likely will be damaged. Antenna Radio Ground Grounded Radio A grounded radio causes the surge to pass directly to ground, bypassing the radio. Antenna Radio Ground...
  • Page 29 Mounting Pole In this case, the surge will be picked up by the Cat 5 cable, and since the POE is not grounded, the route for the surge is through the radio to the antenna, and out through the building. Cat 5 Cable Mounting Pole In this case, the surge will be...

  • Page 30: Cat 5 Cable

    Best Practices 1) Always try to run the Cat5 and LMR inside of the mounting pole wherever possible. This helps to insulate the cable from any air surges. Building Cat 5 Cable 2) Keep all runs as straight as possible. Never put a loop into the cables. 3) Test all grounds to ensure that you are using a proper Ground.
  • Page 31 APPENDIX B: QoS Tranzeo Wireless Technologies’ software takes full advantage of technology to ensure a consistently high quality on-line experience through the use of powerful Quality of Service (QoS) mechanisms. The key to making this applicable in a WISP environment is the Intelligent Stream Handling, a patent-pending algorithm which autonomously manages the flow of traffic going to the Internet, without the need for user configuration.
  • Page 32 Non-latency- sensitive traffic Low – Priority or excess Traffic...
  • Page 34 Decimal Keyword Protocol Decimal Keyword Protocol ======= ======= ============== ======= ======= ======== HOPOPT IPv6 Hop-by-Hop Option TLSP Transport Layer Security ICMP Internet Control Message using Kryptonet key IGMP Internet Group Management management Gateway-to-Gateway SKIP SKIP IP in IP (encapsulation) IPv6-ICMP ICMP for IPv6 Stream IPv6-NoNxt...

  • Page 35: Appendix D: Common Tcp Ports

    IPComp IP Payload Compression Sitara Networks Protocol 110 Compaq-Peer Compaq Peer Protocol VRRP Virtual Router Redundancy PGM Reliable Transport any 0-hop protocol L2TP Layer Two Tunneling Protocol D-II Data Exchange (DDX) IATP Interactive Agent Transfer Schedule Transfer Protocol SpectraLink Radio Protocol Simple Message Protocol Performance Transparency ISSIS...

Table of Contents