Table of Contents
Advertisement
7
OUTLINES AND DIMENSIONS
PLA-RP35BA
PLA-RP100BA
PLA-RP35BA
1
PLA-RP35BAR1
20~45
Fresh air
intake hole
160
Remote controller
terminal block
Branch duct hole
187.5
Suspension bolt
M10 or W3/8
1
60
2
Suspension bolt
lower edge
Control wire entry
M
Air intake grille
M
Corner pocket
Indoor unit
Ceiling
3000mm or more
Grille
Obstacle
1500mm
or more
Floor
OCH416D
PLA-RP50BA
PLA-RP125BA
PLA-RP50BA
1
PLA-RP50BAR1
Ceiling hole
20~45
860~910
810
Suspension bolt pitch
Indoor unit/Outdoor unit
connecting terminal block
Indoor power supply
terminal block(Option part)
160
840
284
377
Power supply wire,
Indoor unit/Outdoor unit
connecting wire entry
Grille
597
Air intake hole
M
M
500
83
Air outlet hole
950
Indoor unit
2500mm or more
from floor
For high
attachment
PLA-RP60BA
PLA-RP140BA
PLA-RP60BA
1
PLA-RP60BAR1
Detail connecting of branch duct(Both aspects)
Branch duct hole
(
Connect the attached
Drain pipe
connected to VP-25
drain socket.
Keep approximately
10 to 15mm space
between unit ceiling
and ceiling slab.
In case of standard grille : PLP-6BA / PLP-6BAMD
Ceiling
Drain hole
In case of auto-grille : PLP-6BAJ
Drain pump clean hole
and Drain emergency
In case of wireless remote controller : PLP-6BALM Auto grille
drainage hole
Emergency operation
Auto vane
switch<Cooling>and
(Air outlet)
Emergency Up/Down switch<Up>
Emergency operation
switch<Heating>and
Emergency Up/Down switch<Down>
DEFROST/STAND BY lamp
Receiver
Operation lamp
Vane motor
Note 1. Please choose the grille between a standard grille and an auto-grille.
2. As for drain pipe, please use VP-25(O.D. 32 PVC TUBE).
36
Drain pump is included.
Max. lifting height is 850mm from the ceiling.
3. As for suspension bolt, please use M10 or W3/8.
(Procured at local site)
4. Electrical box may be removed for the service purpose.
Make sure to slack the electrical wire a bit for control/ power wires connection.
5. The height of the indoor unit is able to be adjusted with the grille attached.
6. For the installation of the optional high efficiency filter or optional multi-functional casement.
1) Requires E or more space between transom and ceiling for the installation.
2) Add 135 mm to the dimensions marked on the figure.
3) The optional high efficiency filter must be used jointly with the optional multi-functional casement.
7. When installing the branch ducts, be sure to insulate adequately.
Otherwise condensation and dripping may occur.
(It becomes the cause of dew drops/water dew.)
8. As for necessary installation/service space, please refer to the left figure.
Models
PLA-RP35/50BA
Refrigerant pipe
··· 6.35
Flared connection
···1/4 F
PLA-RP60BA
Refrigerant pipe
6.35 /
Flared connection
1/4F / 3/8F
(compatible)
PLA-RP71BA
Refrigerant pipe
··· 9.52
Flared connection
PLA-RP100,125,140BA
···3/8 F
17
PLA-RP71BA
PLA-RP71BA
1
PLA-RP71BAR1
90
100
100
90
350
175
Burring hole pitch
Cut out hole
Detail drawing of fresh air intake hole
Burring hole
Burring hole pitch
3- 2.8
125
)
Cut out hole
100
Ceiling
Air intake grille up/down discharge
L.L Filter
Air intake grille
1
2
A
B
Refrigerant pipe
··· 12.7
Flared connection
···1/2 F
9.52
241 258
Refrigerant pipe
··· 15.88
Flared connection
···5/8 F
281
298
Unit : mm
Cut out hole
14- 2.8
Burring hole
150
Ceiling
Unit : mm
C
D
E
80
74
87
400
85
77
440
Advertisement
Table of Contents
