Dsp Functions; Sound Programs - Behringer DR112DSP Quick Start Manual

8
DR115DSP/DR112DSP/DR110DSP
DR115DSP/DR112DSP/DR110DSP Controls
DR110DSP DR112DSP
(1)
(7)
(2) (2)
(8)
(3) (3)
(9) (4)
(4)
(10)
(5)
(5)
(11)
(6)
(6)
(12)
(17)
(14)
(12)
(15)
(16)
(1) DSP display - Backlit display for (8) CH1 VOLUME - Rotate to adjust the gain

DSP functions.

for INPUT 1 and AUX IN. The knob should
generally be set above the midway point for
(2) AUX IN - Connect a media player via 1/8" TRS
microphone signals or turned down for line-
cable. Stereo signals are summed to mono.
level signals.
Control the input gain with the CH1 VOLUME
knob. (9) CH2 VOLUME - Rotate to adjust the gain
for INPUT 2. The knob should generally be
(3) BLUETOOTH LED - The blue LED will flash
set above the midway point for microphone
when Bluetooth is on and searching for
signals or turned down for line-level signals.
connection. When successful connection is
established, the LED will light solid. CH1 INPUT - Connect audio sources using
(10)
balanced XLR or ¼" cables.
(4) BLUETOOTH BUTTON - Press to turn the
CH2 INPUT - Connect audio sources using
Bluetooth function on and off. Use the
(11)
MASTER control to adjust the volume. balanced XLR or ¼" cables.
(5) OUTPUT - Sends the combined signals from POWER INPUT - Connect a standard IEC
(12)
CH1 and CH2 INPUTS out to another device via power cable. To replace a blown fuse,
XLR male connector. carefully remove the fuse holder with a small
screwdriver, then replace the defective fuse
(6) VENTS
with a new one of the same type. Push the
(7) MASTER - Rotate to control the overall
fuse holder back into the slot until it snaps.
volume level. Push the knob to access
DSP functions, which are explained in the
following chapter.
DR115DSP
(1) (6) (1) (6)
(7)
(2)
(8)
(3)
(9)
(4)
(10)
(5)
(11)
(6)
(14)
(12)
(15)
(16)
POWER SWITCH - After all audio connections
(13)
have been made, flip the switch to the ON
position to turn the speaker on. (DR115DSP
only)
AUTO STAND-BY BUTTON - Press to activate
(14)
the automatic standby function. When
activated, the speaker will automatically turn
off after 60 minutes without an input signal
present. When the unit receives a signal
again, the power will return automatically.
(DR112DSP/DR110DSP only)
AUTO STAND-BY LED - The red LED will light
(15)
when the automatic standby function is
activated.
POWER BUTTON - After all audio connections
(16)
have been made, press the button in to turn
the speaker on.
(DR112DSP/DR110DSP only)
FAN VENT
(17)
DSP Functions

Sound Programs

Press the MASTER knob twice to enter the speaker's Sound Programs menu. 'MUSIC' will appear in the display. Press the MASTER knob again to select this program,
or turn the MASTER knob to scroll through the other options - 'DJ' , 'LIVE' , 'SPEECH'. Press the MASTER knob to confirm your selection.
(7) 3-band EQ
Press the MASTER knob once and turn the MASTER knob to scroll through the 3-Band EQ menu: 'HIGH EQ' (treble), 'MID EQ' (mid range), 'LOW EQ' (bass). Press the
(8)
MASTER knob again to enter this frequency menu and turn the MASTER knob clockwise to boost the frequency up to 12 dB, or turn counterclockwise to reduce by
(9)
up to 12 dB. Press the MASTER knob to confirm your settings.
(10)
(11)
High Pass Filter
Press the MASTER knob once and turn the MASTER knob until 'SUB' appears in the display. Press the MASTER knob again to enter the speaker's High Pass Filter
(low cut) menu. Turn the MASTER knob to select between OFF 80, 100, 120 or 150 Hz, and press the MASTER knob again to confirm the selection. Audio below the
selected frequency will be attenuated.
(13)
Delay
Press the MASTER knob once and turn the MASTER knob until DELAY appears, then press the MASTER knob again to edit this function. This function causes the
signal to be delayed a small amount of time to allow the music to be played in time with speakers located further away (e.g. main speakers on stage plus additional
speakers in a balcony).
LED Mode
Press the MASTER knob once and turn the MASTER knob until LED MODE appears, then press the MASTER knob to edit this function. Select 'ON' to always show a lit
LED on the front panel while the speaker is powered on, or 'OFF' to turn the LED off. Select 'LIMIT' to allow the LED to indicate when either the HF or LF limiter has
engaged.
9
Quick Start Guide